Having problems with your Dishwashers ?
My dishwasher stops at the brush part of the cycle- as though it is just stuck. Rest of it works ok.
Probably a heating fault, heater or stat. You have not included a make or model so I am limited to the amount of assistance I can offer.
Repair Help & Product Troubleshooting for Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My dishwasher stops at the brush part of the cycle- as though it is just stuck. Rest of it works ok.
Probably a heating fault, heater or stat. You have not included a make or model so I am limited to the amount of assistance I can offer. ... Dishwashers
I have a SHU3032UC BOSH Dishwasher for a couple of years now. Always worked as expected. Latetly, the dishwasher never stops. It looks stuck on an "unknown cycle"... The cycle dial stays at the "bottom" cycle (there's nothing written). If I turn it 1-2 "clicks", the dishwasher continues its work and ultimatly finishes with very good cleaning results. Once, I open the dishwasher when it was stuck in the "bottom" position, and there was hot watter at the bottom. Here's what I've tried so
Hello, welcome to FixYa.\015\012\015\012Based on you description of the timer not advancing I suspect the thermostat isn't satisfied when heating the water.\015\012\015\012The SHU 30** unit`s with a mechanical timer have very few if any, issues with ... Dishwashers
I have a KitchenAid KDS-17E dishwasher, which has worked well since I acquired it second-hand in 1984. Last night it ran continuously, stuck in the prewash part of fullcycle, with water being pumped through the system, and was fairly warm in the morning. It drained normally when I pressed the Cancel/drain button. I tried the machine again in full cycle. After 20 minutes it was still stuck in prewash, with the water temperature about 42 C, so I stopped it. Machine is connected to cold wate
Your problem is a bad timer.and you really got your moneys worth on this dishwasher.The timers useally go much soon than this one 7-8 years is the norm.The timer gets stuck in one position is a good sign its loseing its ability to fuction normally, ... Dishwashers
BF41 Dishwasher with a leak stuck in mid cycle Hi, I have a 'general domestic Appliance Ltd' BF41 (95+G709394) dishwasher which recently started leaking at the door. After replacing the seal the problem seemed to ease, then recently the problem started all over again and the leaking got worse. A couple of day ago I couldn't stop it leaking and now it's stuck in mid cycle and even though the water is washing inside the machine it never gets hot inside or finishes the cycle. Ive tried stopping and
I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support
... Bosch Dishwashers
Dishwasher Repair Dishwasher is a Stoves/Newhome DW616 Rotating spray arms do not always operate. This is an intermittent problem - will sometimes work normally for a few days then arms will not move at all with no water coming from them. Machine appears to go through its normal cycle. Some times cycle starts normaly and spray arms stop working part way through.
It could be a motor or a pump issue. The dishwasher has a motor that attached to a pump which forces the water up into the sprayer arms and during the drain cycle, it pushes the water out of the dishwasher. \015\012The motor (and pump) located beneat ... Dishwashers
I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.
... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher
I have a kitchenaid dishwasher model KUDS01FKSS0 which is not running. For the past 2-3 months it occasionally stopped mid cycle with water still at the bottom of dishwasher but eventually resumed working. Now it just doesn't run any more and there is water presently in the dishwasher tub). The user interface part (keypad) seems to be working. I can press the keys and the corresponding LED would light up. However after I close the door, nothing happens. There is also no noise what so ever. Any i
THE MOTOR SHOULD MAKE NOISE IF ON, CHECK THE MOTOR OR TIMER. ... KitchenAid KUDS01FKSS Dishwasher
I have a kitchenaid dishwasher model KUDS01FKSS0 which is not running. For the past 2-3 months it occasionally stopped mid cycle with water still at the bottom of dishwasher but eventually resumed working. Now it just doesn't run any more(and there is no water presently in the dishwasher tub). The user interface part (keypad) seems to be working. I can press the keys and the corresponding LED would light up. However after I close the door, nothing happens. There is also no noise what so ever. A
... KitchenAid KUDS01FKSS Dishwasher
GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad
This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers
I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr
Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers
It won't complete a full wash cycle keeps stopping part way through and low rinse aid, low salt lights flashing even though both are full ??? Pamphlet says this might also mean there is a kink in the inlet hose but that seems fine as well. Have had the dishwasher 3 weeks and it has completed about 4 cycles without stopping ???
Check water valve to see if it has something blocking water supply ... Dishwashers
My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914
Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers
The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?
The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher
Delonghi trend dishwasher you select programme and it starts and you hear the pump start and expell water and then u hear water going into machine for 10 seconds or so then it stops then programme selected light starts flashing and the dishwasher starts to heat as though it is in the drying part of the cycle
Please provide the full model number of the dishwasher.\015\012\015\012have you tried to turn the power to dishwasher off and back on.\015\012\015\012What program do you start with? Have you tried the rinse only cycle? does it ... Dishwashers
My Kenmore Elite dishwasher doesn't proceed past the first few minutes of any cycle. It gets stuck at the "add a dish" part of the cycle and then stops and starts. It won't go further into t
... Kenmore Dishwashers
I have GE GSD2300r00bb, it was working just fine the other day no unusual noise, today we tried to run it, just a little bit into the cycle, i heard a strange stalling noise that sound like the motor is stuck or something, i put a camera(in a ziplock bag) in the dishwasher to see if the blade is spinning, no spin, the water did squirt for about 1 sec then stop but still leaking out somewater. Is it the motor or the water pump. I just got this dishwasher about 1.5 yrs. Is this something i can fix
... GE GSD2300RBB Builtin Dishwasher
I have a Bosch integrated dishwater that is just over 2 years old. It has suddenly stopped working and the tray at the bottom is not emptying, although you can still hear a buzzing sound. The cycle does not go beyond this point. I have emptied the tray of water and the dishwasher will start again, and pump water in, but it then stops, as though it is not able to pump water out. Does anyone know what this is? Could it be the pump? A blockage?
... Bosch 24 in. SHU43 Built-in Dishwasher
The wash ('arms' twirling and washing) part of my hotpoint 71340 dishwasher cycle is not working properly - little water soming through - The motor sounds as though it is working although at a higher pitch Draining OK
It sounds like you either need to clean the debris out of the filters and wash arms or the machine isn't filling with enough water. ... Dishwashers
I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?
Our Hoover HD98E Dishwasher stopped working properly today. After a while the machine stops during the power spray cycle and just buzzes as though the pump is powered but not spraying. Is this the pressure pump? It empties Ok cos you can hear the machine emptying...
Its possible that your timer has a bad contack at this spot the machine stops but the drain valves open try advancing the timer one notch to see if it will work if yes relace the timer thanks from gilles ... Hoover 24 in. DT999 Free-Standing Dishwasher
My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402
First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers
BEKO DWD 8650W DISHWASHER, AFTER HAVING GUESTS HOSE SIT FOR US WHEN ON A WASH PROGRAM (ANYONE) PARTWAY THROUGH THE CYCLE THE PROGRAM SWITCH EMITS A BUZZING NOISE FOR A PERIOD OF TIME THEN STOPS, AND CARRIES ON WASHING AS NORMAL. LAST NIGHT IT STARTED A WASH BUT STOPPED PART WAY THROUGH THE WASH AND THEN POWERED DOWN THEN BACK UP AGAIN BUT ALWAYS STUCK AT THE SAME TIME IN THE PROGRAMME, i TURNED IT OFF AND CHANGED PROGRAMMES WHERE IT EVENTUALLY MADE IT THROUGH A 30MIN WASH PROGRAMME, WITH THE BUZ
Dosent heat up or dry ... Beko Dishwashers
Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.
... Bosch Dishwashers
Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.
Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers