Having problems with your Dishwashers ?

When I start the wash cycle it does not get any water, but will continue through the entire cycle. I have checked and replaced the water valve, check teh float and float switch. The handle is working correctly. The selector panel is all elcetronic and I do not know what else to do to trouble shoot. Any help??/


Answers :

I would first check the water valve is it turne on? then are you getting power to the water valve ? if not problem might be in electronic panel.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I start the wash cycle it does not get any water, but will continue through the entire cycle. I have checked and replaced the water valve, check teh float and float switch. The handle is working correctly. The selector panel is all elcetronic and I do not know what else to do to trouble shoot. Any help??/


I would first check the water valve is it turne on? then are you getting power to the water valve ? if not problem might be in electronic panel. ... Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

My dishwasher won't fill with water. I've checked the float assembly inside the washer and it seems to work fine. I've been looking for the float switch and water inlet valve inside the bottom panel in order to 'test' them, but can't seem to easily find them.


If hot or both cold and hot fill try to switch the pipes \015\012if not filling it may be a problem with program and or filter blocked \015\012check also the pump\015\012did you check the water is on as sometimes people forget to sw ... Dishwashers

Asko 1555 Dishwasher will not drain. Bottom of kick panel pan will fill with water triping the float switch?, leaving an error code. Is it safe to assume that the out pump needs replacing. I had the kick panel off and smacked the motor housing a few times and it ran for a few loads, but is now again stopped working.


It might be the pump, or it might be an obstruction elsewhere. If you have an air gap on your sink/counter top, open it and check for debris. If it is clear, unscrew the main filter basket. There is a black plug on the left side of the bottom well ... Dishwashers

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

Bosch dishwaser main motor running no water intake timer stuck outlet pump is working ,inlet water selnoid working,onoffswitch working,float switches is working.


Hi francoisj\015\012\015\012 There might be water in the bottom pan under the dish washer. first turn off the power, then take the kick plate off and you should be able to feel if there is water in there. If there is remove all of it. yo ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

Dishwasher control buttons do not work. Machine is stuck on low wash and headed dry. Pushing butttons on crontrol panel do nothing. Dishwasher seems to work, fills with water , you can here it run it's water agitation, and drains, but only works in low wash


Hello,This means the touch pad has failed, you can make this repair it's simple. Try flipping the breaker off for several minutes this may reset the glitch.Applian ... Dishwashers

I have a Whirlpool which just recently started leaking from the door occasionally and it is most unpredictable. It eventually stops, but before it does it will deposit about a pint of water. I have replaced the float and the float switch, thinking those were the cheapest parts and perhaps the switch was faulty and letting too much water in. That did not work. When this happens I checked the exhaust and hot steam is coming out. Could it be the water inlet valve? If the seal was bad I am ass


Hi\015\012\015\012The issue is with the water inlet valve that is bad and\015\012should be replaced. I believe everything else is working fine. Hope this\015\012helps...please post back for further assistance.\015\012\015\012Dani ... Dishwashers

I have a ge dishwasher GLD5960N that will not fill with water. took off float cap and worked stem up and down to make sure it wasn't stuck. still no water. any suggestions? it was working before, so water supply is good.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher

Kitchenaid dishwasher model KUDS24SEWH2 fills with water, lights on control panel work but doesnt wash or cancel


... KitchenAid Dishwashers

Dishwasher does not fill with water when started. Problem began slowly with dishes not rinsing completely. Overfill float appears to work properly. Water fills pipe leading to fill solenoid but does n


I am almost certain that your problem is the fill solenoid.If it does not work, there will be no water entering your machine.I would either remove it and test it or just replace it at this point.Tim ... Dishwashers

How do i drain the water from my diplomat adp8352 slimline dishwasher ? ive took the front black small panel off but can only see electrics. Im hoping draining the water will get it working again . Its stopped working !


... Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher

My Maytag mdb5130aww dishwasher stopped working; the only function it does is DRAIN. The panel buttons light up. WASH, RINSE etc all do not work. How do I test if the control panel is sending out power to the water pump? What else can I check?


... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Problem with AEG 24in Favorit 40630 Free-Standing Dishwasher When I'm turn on the machine the top and middle signal light are flashing and the pump working for some time and stop. I know this device detects water leaks and is a polystireene float / micro switch that puts the machine in pump out mode. But there are no water under the float! Alex


... AEG 24 in. Favorit 40630 Free-Standing Dishwasher

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

I'm not getting any water into the dishwasher, not on wash or rinse. The float float is working feely and I can hear it click when manually pushed. I don't seem to be getting any power to the valve that controls the water.


Hi pull the wires off the inlet valve under the dishwasher. Then set the dishwasher for a cycle and test the wires with a volt meter while the unit is supposed to be filling. If you are getting 120v the valve is either blocked or bad, you will have t ... GE Dishwashers

I have an electrolux dishwasher Model # EIDW6105GS1 that for the second time has stopped working and all the lights at the top control panel are flashing...what might this mean? I removed the panel down below the door and it appeared to be a drainage problem. The first time it happend was about 1.5 yr after purchase...(No more warrenty and no extended warrenty)...I drained the water in the pan below and it worked once again. After about a month I am having the same problem.


... Electrolux EIDW6105GB 24 in Builtin Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Water won't stop filling, even when the door is opened. I cleaned the float valve at the front , that worked for a few washings. Or it may be a random occurrence. This dishwasher was purchased in 1993 in Canada, and has always worked well. We do have well water, but it isn't real hard, I put vinegar in about nearly every rinse cycle.


... Maytag 24" Built-In Dishwasher - White
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1996 seconds