Having problems with your Dishwashers ?

I have an Electrolux Dishlex DX303 Dishwasher. Recently it has been stopping early in the cycle and the display shows -10. The selected program is flashing. The cycle will restart by pressing the program button again but it no longers wash's right through the wash pe=rogram as it is meant to. I do not have the manual to trouble shoot and find out what this means. Your help would be appreciated. Regards Peter H


Answers :

Hi peter,\012according to manual book -10 is not filling water fast enough.\012check inlet hose and valve, check pressure switch and pressure SW hose and clean sump filter which located bottom of tub that plastic strainer and stainless mesh clean them spotless. sometimes caused by this filter block the water passage and change pressure sw's leadings. and clean sump as well.\012b4 suspect PCB this filter cause many problem like not heating water, doesn't keep water. if dirty filter is the one you will save at least $300- for service man to come out and change the PCB for nothing. I think clean the filter doesn't hurt anyone.\012
\012Service Man K
I have an dishwasher dx303 recently it has been stopping early in the cycle and display shows -21 could you please help me what's problem? Thanks. Maryam
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an Electrolux Dishlex DX303 Dishwasher. Recently it has been stopping early in the cycle and the display shows -10. The selected program is flashing. The cycle will restart by pressing the program button again but it no longers wash's right through the wash pe=rogram as it is meant to. I do not have the manual to trouble shoot and find out what this means. Your help would be appreciated. Regards Peter H


Hi peter,\012according to manual book -10 is not filling water fast enough.\012check inlet hose and valve, check pressure switch and pressure SW hose and clean sump filter which located bottom of tub that plastic strainer and stainless mesh clean the ... Dishwashers

Hi, I have a Siemens SE24A230GB/17 dishwasher and it is not completing the wash cycle (any selected). It appears to be stuck on the 'wash' part of the program. I have done the reset actions as advised in the User Manual and tried another program, without success. I have found that the possible causes could be the timer or thermostat. The estimated time remaining display counts down, but the program does not complete the wash and move onto rinse and dry. Any help or advice you can provide would


... Siemens Dishwashers

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

Hi! We just installed our LG LDF8812WW built in dishwasher. We ran our first cycle and after the wash cycle the dishwasher displayed error code OE. I read that it meant there is a problem with the drainage, and to check the hose if it is kinked. Well, the hose is not kinked and we have no idea why it would have a problem with the draining. We have the hose set up per the installation instructions. How can we check to for something clogged? Any suggestions?


I actually own an LG LDF8812 myself, except mine is stainless steel, not white. So be it. :-)\015\012\015\012Anyway, it sounds like you have just unboxed the unit and it is brand new, not just new to you. I am also ... LG LDF8812 Stainless Steel Built-in Dishwasher

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat


... Asko Dishwashers

Smeg df612sdx Until last week I enjoyed several years faultless service from my SMEG Stainless Steel dishwasher, with the exception of needing to replace 2 x spray arms. The unit has now stopped working altogether. Despite powering up several times, I continue to get both the start/pause and selection programs buttons constantly flash (green lights) when the unit is switched on; previously this only occurred once the wash cycle was complete. Any thoughts would be most appreciated. Thank you


... Dishwashers

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

Initially It started washing, completed the entire cycle, then while drying began re-washing the load. Then it would start washing nothing, without any buttons pressed. Then it woldn't allow any buttons to be pressed for any cycle.Then the lights would flash, but nothing would progress through the cycle.


For replacement parts - head on over to PartSelect.com or \015\012RepairClinic.com and enter in your full model number for a full parts \015\012listing.\015\012I recommend both sites because ...\015\012\015\012\015\012FixYa ha ... Whirlpool GU2300XTVQ Builtin Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

My Defy Dishmaid Silent makes a loud knocking noise when i start the wash cycle, it fills with water but dose not wash.When i start the wash cycle it sounds like it is washing with the added knocking noise but at the end of the cycle the salt has been released but nothing has been washed.A few weeks ago it would run the rinse cycle but now it will not wash on any of the cycles.Please advise.


... Dishwashers

Electronic control pad is pushed for quick wash and the LED display would show 52 minutes. Now when it pushed the display shows 17 minutes and performs all the functions that would occur at the end of a normal cycle. Can set for the longer wash cycle 94 minutes and performs all functions start to finish. Think the control board is bad any advise.


... Maytag 24 in. DWU9902 Built-in Dishwasher

DISHWASHER QUIT WORKING IN ALL WASH CYCLES EXCEPT SHORT WASH CYCLE. YES I HAVE TRIED TO FIX IT. I HAVE REPLACED THE CONTROL MODULE WITH A NEW ONE. ALL WIRING LOOKS CLEAN AND IN GOOD ORDER. NO EVIDENCE OF CORROSION. NOW UNIT WILL NOT WORK AT ALL, BUT "CLEAN LITE INDICATOR' IS FLASHING IN SEQUENCES OF 7. I HAVE FOUND THE SCHEMATIC SHEET BEHIND THE KICK PLATE. AND USING IT I HAVE TRYED TO USE THE DIAGNOSTIC PROGRAM BUT CANNOT FIND ANY PROBLEMS. AFTER DIAGNOSTIC PROGRAM IS COMPLETE THE DI


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012With the symptom you`ve described ( specifically the clean lite ) this is an error of poor water circulation or a heating fault...many times manifesting in th ... Whirlpool Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

BEKO DWD 8650W DISHWASHER, AFTER HAVING GUESTS HOSE SIT FOR US WHEN ON A WASH PROGRAM (ANYONE) PARTWAY THROUGH THE CYCLE THE PROGRAM SWITCH EMITS A BUZZING NOISE FOR A PERIOD OF TIME THEN STOPS, AND CARRIES ON WASHING AS NORMAL. LAST NIGHT IT STARTED A WASH BUT STOPPED PART WAY THROUGH THE WASH AND THEN POWERED DOWN THEN BACK UP AGAIN BUT ALWAYS STUCK AT THE SAME TIME IN THE PROGRAMME, i TURNED IT OFF AND CHANGED PROGRAMMES WHERE IT EVENTUALLY MADE IT THROUGH A 30MIN WASH PROGRAMME, WITH THE BUZ


Dosent heat up or dry ... Beko Dishwashers

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Our Smeg Diswasher, model STA 9452 18" built in is not advancing past the wash cycle. Water does not pump out for rince cycle. I can stop the cycle by opening the door, cancelling the program and restarting on the rince only program. Do we need a new timer?


... Smeg Dishwashers

After selecting wash cycle,I push start button. washing light comes on for a second then goes off.start light keeps on blinking. washing cycle would not start.


Check flood switch float is on(the float under the bottom rack)...also the switch under that...also you ca use a 110 volt test cord to test the inlet valve ... Dishwashers

Bosch dishwasher, Model SMU 7056, UC 09, FD 7309. My older unit has operated flawlessly for years. Two days ago it started to "stall" in one cycle and not progress to the next, e.g., stayed in the wash cycle and would not move on to rinse. In addition the heat generated in the machine was way below normal. A repairman told me that if the water doesn't get hot enough, the unit will not move on to the next cycle. I always use the "Regular Wash" option, but tried other options such as 'Economy


... Bosch Dishwashers

Wash motor My dishwasher was working fine but the timer went out. It has sat there for about 1 year and I have now replaced it. It now cycles through but no water ever comes out to wash. I had an different dishwasher that we use to have at a lake house that would sit there over the winter and all I had to do was reach underneath and spin the little finned wheel and it would work....is there something like this on a DRU141 model? I just have a hard time believing that it is that when everything w


When a dishwasher doesn't get used, the gunk under the float switch dries up. Get that thing moving again, and you'll be back in business! ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

I have a Smeg DWD1SSE dishwasher, that has decided to start and stop on it's own during the wash cycle. We have to restart it at least three times during the 30 min short wash, and it very rarely gets to finish a whole cycle. I have stripped it down to make sure that there is no moisture on the main PCB behind the buttons, which there isn't. I think it looks as though the control board is faulty. If anyone can help or back my thoughts up, I would be very great full. Thanks.


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Our dishwasher (a Maytag - MDBH970AW) will not proceed past the intital intake of water. It has done this occasionally in the past, but with repeated attempts to start a wash cycle, it would eventually work and continue to work for some time afterward. However, in the past week, it will not go through a wash cycle. I have ran the water, prior to starting, to ensure that it is intaking very hot water. When it quits, I can push the start button again and it will go through the 2 minute drain c


... Maytag 24 in. MDBH970AW Built-in Dishwasher

I have a Baumatic BDW 45.1 slimline dishwasher, the unit will power on but I cannot select a program. I was able to place the unit in to reset mode once by holding down 'P' and power cycling the unit. This then allowed me to choose a program and complete a full wash cycle. Now I cannot repeat this steps and the unit remains with just power light on. There are no Error codes displayed at all. Could this be a problem with the front panel?


... Baumatic 18 in. BDW45.1 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1637 seconds