Having problems with your Dishwashers ?

My Bosch dishwasher does not start. Instead it just ticks. I am not aware of any timer that it has. We have let it tick all night. One time in the last 20 attempts to start it (by closing the door) it did start but not since. Model number SHX46B. It is about 5 years old.


Answers :

Hi.

It is possible that the timer board is responsible, timer board however is an expensive part and fails rarely.

Before replacing control, if there is no water coming in check:

Door lock
Inlet hose at the back
Inlet valve
water level sensor (float or pressure)

If there is water getting in but cycle does not advance check:

Hot inlet in valve (if valve is dual)
Heating sysem (if valve is not dual0
Thermostat
water level.

If all the above is Ok go for the timer board, that is likely the problem
Hi
\015\012
\015\012Please check your control board checked.If the dishwasher does not start, first make sure that the door is properly latched by shutting it completely. Check whether the dishwasher is turned on. The "On/Off" button is located on the left side of the control panel. Press the button one time to turn the dishwasher on. For models featuring a concealed control panel, meaning that the control panel is located on the inside edge of the door rather than on the door's face, the unit will not start unless a wash cycle has first been chosen. Finally, the "delay start" option may need to be canceled. This option allows the user to delay when the dishwasher's cycle begins by up to 24 hours. To cancel this option, press the "+" or "-" buttons on the control panel until "00" is indicated on the digital display panel.
\015\012
\015\012Let us know if you have something more to ask else please accept the suggestion.
Thanks for contacting fixya.com
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher does not start. Instead it just ticks. I am not aware of any timer that it has. We have let it tick all night. One time in the last 20 attempts to start it (by closing the door) it did start but not since. Model number SHX46B. It is about 5 years old.


Hi.It is possible that the timer board is responsible, timer board however is an expensive part and fails rarely.Before replacing control, if there is no water coming in check:Door lockInlet hose at the back ... Dishwashers

For my Kudi01dl model dishwasher, the rinse light is on, but the unit will not respond to any buttons being pressed and won't turn on. When I press any buttons, two horizontal lines show in the front, but go off as soon as I let go of the button. Is there a ways to reset the unit? Everything was functioning fine the last time I used it. I use it about once a day. The problem started when I heard sounds coming from the unit, very loud motor sounds. The door was closed but I had not turned


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Our Kitchenaid dishwasher model # KUDP021R will not start. We close door, select wash and press start. The control lock light at the top which is lit flashes a few times and then stays lit. Dishwasher remains silent. An aside which may be helpful is that the door has always seemed to be not quite straight...as though it had to warp a tiny bit to close and lock.


The problem you have already identified could be the door switch is not closing when you shut the door. Please confirm your dishwasher is KUDP02I (i and not 1).\015\012\015\012One way to check is find out the door switch on the door panel ... KitchenAid Dishwashers

I have a fisher and paykel single door dishwasher model dw918 td. The other day its door spring collapsed and the door had a free fall. The dishwasher operated fine. But we have accidentally opened the door and let it free fall under its weight a few times. Last night the dishwasher began its cycle and stopped after 10 minutes - no beep, no alarm, display was fine. it just stopped. I opned and closed door a few times. Pressing the start/stop button only resulted in a beep but no action. I let


... Fisher and Paykel Dishwashers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

Cannot start After loading, I press Normal Wash, press Sanitize, press Start and door will not close/lock!!!!!!!!!!!!!! I have used it 5 times and now it will not close and start. Very frustrating Model GLD2445RFQ2 Serial TH91576214 delivered 9/3/09


The problem you maybe having is your choosing the cyc first which is ok but I have not seen even with the newer models that have a self closing door push the door closed and latch catches then push start on some newer models you have to push and hold ... Frigidaire Dishwashers

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

I have a dish washing machine bauknecht model gsx 7988, when closing the frontdoor, the pump starts to run and a beeping sound is noticed, this beeping sound and automatic running of the waterpump happens on any selected program, when opening the door, the grren startligt is flashing two times fast,then a halve a second out and then flashing again two times fast etc.etc filter is clean, waterpressure is ok, eno other program can be started.pls help.


... Dishwashers

I have a fridgidair dishwasher model FDB4315LFBO and none of the buttons are working this is the second time this happened and last time i removed the cap for the rinse aid and heard a rush of air then everything started working. I already turned off the power to reset things and the PF light flashed until i opened the door then it went back to everything being dead.


Sounds like something has burnt in the main powerboard. ... Dishwashers

Serial #88445-B Rym 717881 model # fpdd 603 We are getting a fill fault code when we start the dishwasher. When the alarm goes off we have to pause the wash cycle open the door and then close the door if we do this about 2 or 3 times it will wash. It seems it fill with water but it seems to be low on water Dave Heller


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool Quiet Partner II model DU1145XTPS7 normal light repeating continuously. Then Cancel light started blinking too, at the same time after I tried sequences suggested in earlier posts. Do I try sequences with door open or closed? How many times do you press buttons? Please help! Thank you.


... Dishwashers

Free standing hobart model KDD 60A Serial # 222601715 Washer does not start when door is closed and locked. Electrical power to wall socked operating. Machine plugged in. Water supply connected. Start attempted in rinse cycle and wash cycle.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or door\015\012lock switch which is not engaging its ... Hobart Dishwashers

Door Catch Model: S51M53X0GB/28 Hi there, Door is not closing properly since last washing cycle and is preventing the machine from starting. Just over 2 years old so just out of warranty. Any ideas?


... Neff Dishwashers

Kitchen aid dishwasher model#KUDSO1FLSSO CLEAN LIGHT BLINKS7 TIMES- I DID THE RESET SANIRINSE-ENERGY SAVER-DRY ETC... CLOSED DOOR NOTHING. WE DID HAVE TO REPLACE THE ELECTRONIC CONTROL ASSEMBLY (PART# 8564542 ) BY THE " CONZ"AREA IT WAS BURNED AT THE TOP BY THE "T" AREA. NOT SURE IF THAT HELPS MY HUSBAND IS OUT WITH FRIENDS TONIGHT HE GAVE UP WE HAVE UNPLUNGED THE UNIT AND MY HUSBAND SAID HE EVEN DID OUR BREAKER- HE CAN FIX ANYTHING BUT THIS IS REALLY STARTING TO p... HIM OFF AND WANTS


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Kenmore Model #665.15891791. When door is closed, time display shows 18 and quick rinse LED is on. Dishwasher will not start.


... Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

Myy kitchenaid dishwasher model kudi01flss doesn't start even though the lights on the panel light up so I opened up the door to look at the latch and found a broken plastic piece that appears to be part of the latch. Could this be why the machine doesn't start. The funny this is the door still seems to snap closed even with this broken piece but what I'm thinking is that this piece activates some sort of electrical connection that turns the machine on when the door is closed. Any thoughts on th


... KitchenAid KUDC25CH Dishwasher

I have a bosch SHU8815UC dishwasher. It was already installed when i moved into my apartment - so I'm unsure of the age. The dishwasher isn't functioning. When I open the door, the "Clean" light and the PowerScrub button are red. When i close the door, the light go off but nothing happens. One time I closed the door, it started to rev up but would shut off and beep three times after about 1 min. No water comes out. Any ideas? Thanks! June


... Dishwashers

My dishwasher is a Smeg model STA 6143, and the door won't close. It seems fine until the last few centimeters, then it jams and won't close easily. If you press hard, it'll shut but not latch. Nothing appears to be stuck anywhere. We've tried jiggling the door but it seems somehow to be misaligned, although there's no reason why it should all of a sudden appear to be so. The electronics work fine, the racks fit fine (we also removed them, and the door still won't close), and nothing appear


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1712 seconds