Having problems with your Dishwashers ?

I have an LG dishwasher LD2120WH and the waste water pipe has split right where ti endered the machine. Can I remove that little white 'plug' and re-connect the pipe or do I have to buy a completely new one? Can you assist me. Also the wheels on the trays dont last and I would need some of those too.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an LG dishwasher LD2120WH and the waste water pipe has split right where ti endered the machine. Can I remove that little white 'plug' and re-connect the pipe or do I have to buy a completely new one? Can you assist me. Also the wheels on the trays dont last and I would need some of those too.


... Dishwashers

I have a brand new Blanco dishwasher but im unsure if it is a DWF6XP, DWF4X or DWIN7 model. It does not have a salt dispenser if that helps. Last night when running for the first time i had a plumbing issue where the drain pipe was not set high enough as it states it has to be 500 to 100cm of ground height. Also had a leaking sink drain pipe. Fixed all that and turned machine back on and it pumped all the water that was inside to drain. I have cancelled the program and restarted but now it is ru


Unplug it and wait 5 minutes. Plug it back in. This will reset the machine. Put it on full cycle and allow it to do a full cycle. It should work just fine. ... Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

11 hp honda pressure washer engine won't start. No spark at the pkug, bought a new coil and still no spark. This sysem only has a coil off the fly wheel and the spark plug. I even changed spark plug. Use the unit the other day, shut it down and on restart it won't start. Also, I disconnected the kill switch and the il lvel sensor so nothing was going to ground.


If you replaced the coil,check the wire and boot,check with meter for continuity.could be loose connection to spark plug ... Honda Pressure Washer PSI 3000

Good morning, I have a F&P dishdrawer ds605i (i think!) single drawer intergrated front. I dont know whats happened to it. The last cycle it decided not to empty the water out, so i manually emptied it. Now it seems stuck. All it does is run the fan. i can't start a new cycle. The start/pause button allows me to open and close the door as normal and i can hear the lid opening and closing.......... I have tried turning it off for a day at the wall switch. I have also noticed i can


Hi \015\012I guess the model no. you have sent is not correct,however given bellow are links from where you can troubleshoot your problem to your dishwasher which is related to your issue:-\015\012 ... Dishwashers

Probe and swich is not working properly.There is four cable, 2 black..its working.other 2 cables Red not connecting.When i short the cable system is working. My hobart dish washer is old I dont know the correct model no.But the part no. is 00-271621 pls replay me as soon as possible I bought a new probe and switch that also same condition.


... Hobart AM15-6 Dishwasher

I have an Ariston LI45. The stupid thin one. It's not seen much work & is just out of Guarantee. It's stopped working & is showing 2 flashing lights. Stops partway in to a cycle with water in the base, but not enough to cover the element. Tried re-setting, no difference. I have also noticed that it's melted a plastic wheel off the bottom tray at the back. After reading problems with other washers, i'm guessing the water level switch & maybe element too. If this is the case, i'm ok finding the


... Dishwashers

Hi, I have a 10yr old Neff s5543 built-in dishwasher, it is has been working fine but recently has stopped fully draining. I have removed it from the housing and checked all pipe work is unblocked and not kinked, have also blown back down drain tube to free any blockages from drain pipe, have also removed pump cover and checked around impellor for any foreign bodies etc. Everything seems clean and free. I ran a complete heavy cycle (empty dishwasher) and allowed drain pipe to drain into a


Hello there and thank you for choosing fixyaOk there are acouple of things that can be checked on this along with what you have already checkedDrain solenoid\015\012 \015\012 \015\012 \015\ ... Neff 24 in. S5543X2 Built-in Dishwasher

On our Hobart Dishwaher, Model AM15T, S/N-23-1000-664 won't start with message wrench & P2. The Thermistor is not open or shorted with resistance reading of 64 Kilo-ohms. I suspect that the Relay Board P/N- 892934-2F is not good. I installed the New spare board P/N 892934-1 Rev.F, but no display at all. Is this the correct PCB? Also the Thermistor is on one assembly with float switc. The new spare we had is only a Thermistor P/N F370609. I also checked the 3- Thermostat on the Tank and they are


... Hobart Dishwashers

The flimsy plastic guide wheels on the rack for my (ca. 2000) GE monogram dishwasher have been breaking. Six so far. GE wants $25 - $30 per wheel to replace and $235 for a whole new rack!! I will not reward this rapacious corporate behavior. Is there an appliance graveyard (like an auto wreck yard) where one can get a used rack? Are there wheel manufacturers/suppliers that will sell reasonably wheels of similar dimensions to the breaking wheels? Preferably in nylon or stainless steel, not the cr


We have just solved the problem with our wheels falling off! For .75 cents a wheel we purchased new wheel "clips". The connect straight into the wheel instead of "rotating" on. Big differnence and so easy to change out! 5 minutes and the problem is g ... Dishwashers

Hello I have a built in DCS dishwasher - width 24" heigh 35". It started smoking out the front and the repair man said it needs a new control board. Is that possible or should I buy a new one. IT is not a dishdrawer its a full dishwasher. the top rack is also broken. If I need to buy a new one - where from - new jersey area


Http://www.thefind.com/appliances/browse-dcs-single-dishwasheryou can purchase online from here... ... Dishwashers

Hotpoint dishwasher I need to change waste pipe on my hotpoint dishwasher. I was given this dishwasher by a friend and it works well but I cant connect the waste pipe to the bit under the sink as the rubber connection on the end is missing. I bought a new waste pipe but not sure how to connect


Did you have a dishwasher before? If so, you must have had a sink tail piece with a dishwasher drain coming off the side. For the connection, you may have to get an adapter to fit the end of the dishwasher drain hose to the sink tail piece. Take a ... Dishwashers

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

Good Morning, I don't need any help except to get rid of my lg dishwasher because it is the worst dishwasher I have ever had!!! I have had it fixed once(new motor ,new soap tray,new board) and it still does not work good and still smell like it is burning up. I have not been as unhappy with anything in my life. WISH I HAD NOT HEARD OF LG AND WASTED A LOT OF MONEY!!!!!!!!!


Hi,You might be interested in this.....http://www.contacthelp.com/directory/Shopping/Electronics/LG?ListingID=386heatman101 ... LG Dishwashers

Siemens dishwasher help i have a siemens dishwasher with no manuals and on my fresh water pipe there is a box which has a electric sign on it this also has another arrow on it is this a flow arrow? my copper pipe has my outlet on the top should my outlet be underneath to suit this arrow and the water is flowing down and not up the pipe thanks ****.


My siemense dishwasher (2 month old) stopped working\015\012No matter which program I choose, after 1 min the program stops and I get "tap" symbol on the led display. \015\012Instructions says it might be a problem with the water source b ... Siemens 24 in. SE25T250 Free-Standing Dishwasher

Im having a problem desiding how to hook my drainage pipe up from the dishwasher i cant put it next to the sink cause theres no room so i have to put it on the other side of the kitchen could i connect new pvc pipe to the drainage pipe underneath the floor or do i have to put it above the trap


You can put a new verticle pipe up from under the floor and put the drain hose in that. make sure the vertical pipe comes up to about worktop level and make sure there is a water barrier in it or you will get a nasty smell ... Dishwashers

I am trying to fit a new outlet pipe to the dishwasher Hotpoint DWM 37 but the old pipe won't come out, what do I need to do? ( I have got the white clip off the back but the pipe seems to be fitted into the dishwasher itself)


... Hotpoint 24 in. DWM37 Built-in Dishwasher

How to install new wheel on Simoniz S1600 pressure washer


... Pressure Washers

Zug adora 12 s dishwasher and I need a new center plastic tray


... Dishwashers

Hi, how do i install my dishwasher....i dont know where to connect the water supply pipe to as i dont seem to have a tap under the sink for it to be connected to, can anyone help please.


You'll have to tap into the hot water supply for the sink to get a connection for the dishwasher. This is a moderatley difficult plumbing task. If you don't have plumbing experience, it's probably best to call a plumber.\015\012\015\012 ... Dishwashers

Dishwasher I am getting a run around with getting my LG dishwasher fixed properly. We had a tech more than once come in and look at our dishwasher. It has not been fixed and never dried the dishes properly. It is now leaking and going to a "del" level when we attempt to wash the dishes. It is also leaking on our fairly new tiled floor and under our new kitchen cabinet. Your tech stated the dishwasher was not installed properly. The installation dept , Francine stated it is not their problem


Not sure what you mean by a "del" level, but as far a drying issues:\015\012\015\012LG chose to use a very energy efficient drying method which relies on the residual heat of the dishes to help dry them rather than many manufacturer ... LG LDF6810 Built-in Dishwasher

Water Connections I have a new house with an Asko 1805. I think it is only connected to the cold water pipe. Can i connect it to hot as well, to reduce its cycle time?? If so, how can I access the connections? The front foot panel doesnt reveal any pipes.


In the US dishwashers are usually connected to the hot water supply. Although the ASKO 1850 I believe has an in line heater. Using hot water supply will reduce electrical useage.\015\012\015\012Interestingly we use to have ASKO washer and ... Asko 24 in. 1805 Built-in Dishwasher

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1001 seconds