Having problems with your Dishwashers ?

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

Asko D1996 Dishwasher - Tank fills with water but it "washing" cycle never starts. However, the heating element begins the work and with no water running over the heating element it smells like something is burning. I have tried changing the programs from Pots and Pans to regular wash but the same results. Nothing happens


... Asko D1776 Stainless Steel Built-in Dishwasher

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Asko D1996 Dishwasher - Tank fills with water but the "washing" cycle never starts. However, the heating element begins the work and with no water running over the heating element it smells like something is burning.


... Asko D1776 Stainless Steel Built-in Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

We have a hotpoint DWF30P/17 Dishwasher which no longer heats or washes with hot water. The cycle completes the wash but no hot water. Can you advise? thermostat element controller


Before I went with the controller, I would probably try the heating element itself, they are usually not that hard to replace and may be cheaper. I know its not that much advice, but just trying to help. ... Dishwashers

I have a haier dishwasher model WQP12 AFM, I've replaced the wash pump motor and drain pump (they had been damaged with water after last repair person didn't put widget around drain hose which split and water accumulated on bottom). It well for about two weeks, then it would not go through it's cycle and I noted water not heating up. Have checked element with meter, thats fine, I replaced timersince it wasn't going through its cycle and that has not changed anything. Any suggustions?? Cheers


... Haier Dishwashers

I have a kenmore ultra wash quietguard deluxe & notice it has been connected to the hot water supply. As I am making some changes I would prefer to connect the cold water supply will this make any difference to the operation of the dishwasher. The unit is less than 2 years old. Thank you


Depends... some units heat the water for you in which case it would not matter and would infact save you money over time. If your unit does not heat the water your going to want to leave it alone for better cleaning performance. Check your owners man ... Kenmore Dishwashers

Dishwasher We have a Trieste dl06-07 s/s dishwasher , the diale or timer seems to get stuck during the wash , I've checked the water and it's cold , is this the thermostat problem , cheers


... Dishwashers

I have a frigidaire dishwasher (FDB1050REM2). When I start it, i heard water going in but when it is time to start washing it stops. I have found a burnt connection on the high limit thermostat. I have change the connector, but still doesn't work. Is the thermostat gone?


Thermostat should not stop motor. ... Dishwashers

Beko dishwasher DE3431FW washes and goes through cycle but does not heat water,ive changed heater element and changed pcb. new pcb does not turn on machine? old on does.changed thermostat.what could it be?


... Beko 24 in. D3731F Free-standing Dishwasher

The water in the dishwasher is always cold with no heat so a poor wash. Does the dishwasher have a built in heater element?


... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

Beko dishwasher its only washing in cold water is it the element


Hi there.....there is no element as such...it is whats known as a through heater....can be difficult to test in situ....however if testing ok then you require a replacement rogramer\015\012\015\012regards Sir Galahad ... Beko 24 in. D3731F Free-standing Dishwasher

Smeg dwf612ss dishwasher only washing in cold water and not drying the dishes


... Smeg 24 in. DWF612SS Free-standing Dishwasher

Hot point dishwasher washing in cold, have replaced heating element no change . can you help


Check the thermostat and eventually replaced, if it is not the thermostat , then it is a defective cycler/timer control assembly.If your dishwasher has also hot water power supply, try also increasing incoming hot water temperature. ... Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

Hi Machine is Hoover Dishwasher HND6515 Is washing cold. would this be the thermostat or element? Thanks Rachael


Try doing a continuity test on the element with a multimeter this should tellyou if it is the element\012Thanks \012Rick ... Hoover Dishwashers

Hi, My westinghouse dishwasher SB907 goes through the washing cycle but doesn't seem to heat up and use the hot water. I have changed the little switch thing, that costs around $20, so what else cold be the problem?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Dishwashers

Diswasher TYP NBKH, SERVICE 8546 892 10010 Problem: For all programs except rinse and charge 1/2 for all programs. Pre-rinse and rinse for 50 Bio, 60 and 70 OK. Downloading water to wash causes multiple knocking (on the left side dishwashers) and simultaneous blinking light (relais?). Opening doors and adding water (different amounts - from 0.5 to 2 l) brings the normal work of dishwasher back. Rinse with cold water after washing OK. Final cleaning with hot water causes knocking again. After r


... Dishwashers

Do these 'portable' dishwashers 'heat' water prior to washing? i have customer complaining bout the dishes not coming clean..yet the water entering the dishwasher is cold, does not appear to heat water prior to washing.


Most dishwashers require a minimum 120 degree inlet water temp. The heating element will boost this up during the main wash cycle to aprox 140. Do not hook a dishwasher up to inlet water temps above 150. ... GE Hotpoint HDA3500N Dishwasher

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

The dishwasher fills with water to the level of the heating coil, when the wash clyce starts it pumps water but not enough to turn either spray bars. I have changed the chopper and wash impeller, cleaned the filters and float assy. Changed all the seals but it will not turn the sprayers. Help??


It sounds like a serious loss of pressure. I have a couple of question for you that will help me assist you.Can you get me the complete model number from the tag just inside the door?Does any water leak on the floo ... Kenmore 16632 Built-in Dishwasher

Smeg dishwasher my smeg dwf409 dishwasher pump keeps on running will not stop after washing cycle and there is water leaking from the bottom of it i can not see any leaks around the pump does the tray on the bottom always have water in it


My hotpoint dish washer aquarius is 4 years old leaves a sandy grit all over dishes water not spraying the top,done all the usual stuff run out of ideas ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2838 seconds