Having problems with your Dishwashers ?

After the last wash I noticed the bottom of my dishwasher (Whirlpool quiet partner 2) was filled with water. After unloading the dishes I closed the dishwasher and pushed the Cancel/Drain button but the button didn't work. None of the buttons work. It's as if the dishwasher became unplugged. I looked at the nearest outlet beneath the sink, but did not find anything unplugged. I wasn't able to drag the dishwasher out of its area beneath the counter by myself and figured I better ask first be


Answers :

1.Check the drain filter for clogging.
2. Check the drain hose. Remove carefully to avoid water spill.
3. Check whether flows freely from the hose.
4. Check the drain valve if possible for you.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After the last wash I noticed the bottom of my dishwasher (Whirlpool quiet partner 2) was filled with water. After unloading the dishes I closed the dishwasher and pushed the Cancel/Drain button but the button didn't work. None of the buttons work. It's as if the dishwasher became unplugged. I looked at the nearest outlet beneath the sink, but did not find anything unplugged. I wasn't able to drag the dishwasher out of its area beneath the counter by myself and figured I better ask first be


1.Check the drain filter for clogging. 2. Check the drain hose. Remove carefully to avoid water spill.3. Check whether flows freely from the hose.4. Check the drain valve if possible for you. ... Dishwashers

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

I have a Rebadged Siemens dishwasher model no. SE6TIE1GB / 13 TKD 795 / 2. When turning on, the dishwasher makes the "normal" noise of washing but after less than a minute it stops and refuses to wash anything. Ive tried pressing the reset button but no help. Worth mentioning, the night prior to that, I switched on the dishwasher before sleeping and when waking up at 5am, it was still washing so I manually turned it off and opened the door to find some water at the bottom of the tray.


... Siemens Dishwashers

I have a Dishlex Global 300 dishwasher that stopped working mid-cycle. I had to sponge out all the water. Now none of the buttons do anything and none of the lights come on. When I turn it on at the power outlet it gives a single beep, but I cant get it to do anything else. I've opened it up and there is no water or dampness anywhere inside. Any ideas?


It is your control board inside your dishwasher. ... Dishwashers

Quit mid cycle - no apparent power issue - house breaker OK - Outlet OK - Will not do anything - Checked the one fuse I could find in the control panel area - it tested OK. Is there another fuse/breaker in the dishwasher that may be the issue?


There may be a thermal fuse in the rear of the machine. If the door switch is faulty (which is common) then the machine won't do anything either. You can test the power from the power inverter to the control board with an ohmmeter to see if there is ... Whirlpool Gold GU2475XTV Builtin Dishwasher

My Whirlpool dishwasher will wash fine, but when it drains, it's a slow trickle. I've snaked the line from the sink to the washer, but I can't find a clog. If I try to blow into the drain pipe all I accomplish is almost passing out. I can't blow all the way through it. When I hit the drain button, I hear the solenoid kick on with a rattle, then just a hum. Like I said, I just get a trickle, and the basin never drains completely. It's driving me crazy! Help? Thanks.


Ok, don't fret too bad, help maybe just reading.Disconnect the drain hose from the sink/garbage disposal, get a big bucket, stick hose in bucket, making sure that end of drain hose does not get lower then the bottom of dishwasher. Turn di ... Whirlpool 24 in. DU1055XTPS Stainless Steel Built-in Dishwasher

The auto clean button is lite on my maytag dishwasher and I can't figure out how to shut it off. Nothing will work. I have looked in the book and can't find anything to solve this issue.


I had the same problem, but the delay, sanitize, and high temp lights were on as well. I had just installed a new furnace, and I realized that the electricity may have been interrupted, and that the unit may be caught in a loop. so, I flipped the pow ... Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

My Whirlpool dishwasher will wash fine, but when it drains, it's a slow trickle. I've snaked the line from the sink to the washer, but I can't find a clog. If I try to blow into the drain pipe all I accomplish is almost passing out. I can't blow all the way through it. When I hit the drain button, I hear the solenoid kick on with a rattle, then just a hum. Like I said, I just get a trickle, and the basin never drains completely. It's driving me crazy! Help? Thanks.


In the bottom of the dishwasher, there is a screen. Remove it and clean it and the drain underneath it. Make sure the POWER IS OFF before you start. ... Dishwashers

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

I have just had a Whirlpool dishwasher Mod GU2275XTVY1 installed. It ran thru the initial cycle perfectly. Today it will not start. The start-resume button is flashing and nothing happens. I cannot find anything in the instructions about this. What is wrong?


... Whirlpool Dishwashers

Hi, Where is the reset button on the Whirlpool Gold Quiet Partner 111 Dishwasher /Model GU1200XTLT3, Type 575-0. When I had my sink faucet replaced, the Control Lock light came on and I couldn't run anything on my Sensory Wash Cycle panel. I tried unplugging it for a while, no luck. All the circuit breakers are fine. THANKS FOR YOUR HELP! Kathy Bonner


Hi kalybon,\015\012\015\012  There is no "RESET" button on Whirlpool Gold Partner 111 dishwasher. :(\015\012\015\012Regarding your issue, it seems to be a case of Control Card.Sorry to be bearer of bad news, you need to replace ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

I have a Kitchenaid dishwasher, KUDP01FLSS5. Just now I used the normal wash and sani rinse cycle. The tub did not fully drain, and the lights on the buttons are unresponsive. I have power at the outlet, but nothing is happening at the controls. What can I do? I am an electrician, so if anything needs to be replaced let me know.


Hello. turn it off at the panel for two full minutes. that will reset it. Then push the drain button and hopesully it will respond.\015\012\015\012If not get back. Joe ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Westoint Dishwasher I have looked in the manual under troubleshooting tips, but didn't find anything on the problem. The dishwasher goes into cycle,but during the wash cycle it stops,makes alarm and the wash and rinse ligts come on. And now I can't even find the product on this site.Westpoint Dishwasher WQP12-9240. Thankyou My dishwasher is stopping at stage 2 of the programme after beeping once. Quite often the detergent flap doesn't open. Am at my wits end and threatening to leave home!!!! Th


Hi again,\015\012\015\012That should be OK. Just get in touch with your sales rep or his boss. Somebody there will be able to look up the record of the purchase. If they ask for model & serial numbers, you have them. You will find ... Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

Have the same problem as other with the maytag quiet series 300 model MDBS561AWB dishwasher. Two of the buttons on the front light up, but dishwasher will not start. Don't know if CBoard or the buttons or the ribbon cable is the problem. Took the door apart and couldn't find any condensation....Looks like maytag has done it again......could use some help with the cost of replacing all those parts. Will help me decide if better to buy new dishwasher.....preferrably not a maytag or whirlpool, or a


... Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

My dishwasher worked just fine yesterday afternoon. I loaded the dishwasher again after dinner and tried to start it, but I got no response from the buttons on the left side of the panel. The buttons on the right side (hi temp scrub, sani rinse, and air dry) light but don't do anything. I also get no response from the delay hours, start, or cancel buttons. Help?


... Kenmore 24 in. 16939 Built-in Dishwasher

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I have a Maytag Quiet Series 100 dishwasher. There is an icon with a "3" in it just to the left of "heat dry." I just noticed this "3" light is on and the dishwasher won't start when I push the "start/cancel" button. All that happens is the "3" light flashes when you push any of the other buttons, but it won't do anything else. Any help you can give me would be greatly appreciated. Thank you.


The "3" means hold for 3 seconds to child proof it. When it's on, none of the functions work. When you hold it again for 3 seconds, it turns off and your buttons will work again.\015\012Good luck! ... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a Frigidaire Gallery Series dishwasher (model. GLD3450RDB0) that always displays the "lock" icon under the no heat dry button. I am able to get rid of it by holding the button for 3 seconds, but I am still unable to select anything or get the dishwasher to start afterwards. As soon as I close the door, the unit locks again! What can I do?


Have you tried unplugging the dishwasher for a while then .. Trying it again.. If the problem still persists have a cleaning done to the control board and touch pad inside and if still the problem persists then i doubt whether the problem is that the ... Dishwashers

Hi there, we have had our dishlex 300 dishwasher switched off for a while and today I turned it on. I started a cycle and it stopped after a few minutes and then the Eco button started flashing. I opened the dishwasher to find it full of water and leaking out of the button. Please help! Regards, Pania


Hi just read your posting.Now the reason these dishwashers flash ECO is because there is either water in the bottom tray or your drain pump is open circuit.Is the machine making a pumping noise when it is flashing the ECO light,or is it completely si ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2374 seconds