Having problems with your Dishwashers ?

My dishwasher is leaking water near the bottom of the loading door when running. Can someone tell me the most likely cause And possible repair ideas. It is a 1999 kitchenaid.


Answers :

If the water is comming from the door corners its from oversudsing or was something caught in the door within the door seal
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher is leaking water near the bottom of the loading door when running. Can someone tell me the most likely cause And possible repair ideas. It is a 1999 kitchenaid.


If the water is comming from the door corners its from oversudsing or was something caught in the door within the door seal ... Dishwashers

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a MODEL 577-0 kudk01ILb55 KITCHENAIDE dishwasher. I am trying to remove the inner pplastic bar that goes vertically through the system from top top bottomj so that I can clean out the filter. But I do not see how to remove that bar. I have looked online for a repair manual of some type but have been unsuccessful. Can someone tell me how to remkove the bar so I can get to the filter on the bottom? I have already removed the star shaped rinse sprayer.


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Own a KitchenAid dishwasher, model KDC-21AD. Unit stopped shortly after startup cycle began. When cycling thru the various wash cycles, I hear a slight hum when selector switch is at the "pots/pan" selection. About 2" of water is standing in base of dishwasher and it will not start. Checked the KitchenAid site and they do not list my dishwatcher. Would like to be able to repair myself or have it done at reasonable price.


... KitchenAid Dishwashers

1987 In-Sink-Erator Classic Supreme (Just like KitchenAid from that era) - leaked Jet Dry after it was filled. Haven't taken door apart yet to figure out what is wrong. Also, after washing/rinse/dry is complete, dishes have light coating of white powder-like film that wipes off. What could be the cause(s) of these issues?


You have to replace the rinse aid compartment if not the whole inside door shell ,the reason for the coating is because your not using rinse aid.If you are using the same soap than you need to replace the leaking dispensor. ... KitchenAid Dishwashers

The power washer leaks fro the base when pressure is applied. I removed the bottom housing and the round gasket that houses the bearing is badly damaged. I would like to obtain a repair manual and possibly order some parts. email [email protected]


... Pressure Washers

I have a Kenmore Quietguard Standard that I purchased around 2005. It will begin the cycle, but 'sticks' and makes a loud screeching sound... like it sticks when it's to begin washing. Help! I'm lost without my dishwasher and know nothing about repair but I think I might be able to if I knew what was causing this and what to do.y


... Kenmore 24 in. 15142 Built-in Dishwasher

I have gcv 160 5.5 hp power washer my problem is that the high pressure pump is not working properly when the engine is running the output pressure is very low so i would like to know could be the possible cause of that problem


look for a black plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the top plate then pull out the piston inside - if unable to lift out, start unit and watch it pop ... Karcher 2500 PSI Pressure Washer

I have a PW1686 power washer but it runs for a few minutes then cuts off. After a few minutes it starts again then goes through the cycle of on and off. Kindly tell me what are the possible causes.


The problem sounds internal (perhaps the temperature cut-off switch or the auto-start-stop switch). For safety and possibly warranty reasons, you should not open the case to investigate or repair; take the unit to your local service center. ... Campbell Hausfeld PW1750 Electric Pressure Washer

Hi I have a Whirlpool dishwasher Model #DU912PFG01 Or DU912PF001 or DU912PFGG1 cannot tell the last 3. Serial # FK194309. My son noticed the dishes didn't look clean, he added DISHSOAP which then produce a huge amount of suds. Anyway hav run the cycle thru with vinegar and it doesn't seem like water is moving throughout the diswasher, just on the bottom. DO you have any ideas, it runs thru all the cycles.


Slog builds up in the drain pipe right before the garbage disposer. I had to replace mine when I replaced my old dishwasher. If you put vinegar in the dishwasher to unplug the pipe, the vinegar could have loosen all the slog and clog the drain ... Zanussi 24 in. DE6965 Built-in Dishwasher

What does Frigidaire dishwasher timer code "Hd"stand for? It's not listed in the manual and I couldn't find it listed online. If it's just a "Hold" code (which is what I suspect) for extra washing time, what would be causing that? I'd like the shortest wash time possible to save $$$ and resources. Model number is BGBD2432KFO. Thank you.


“HO” or “Hd” means the \015\012dishwasher’s cycle time is being extended while it is heating water. At \015\012certain points in the wash cycle, the dishwasher uses hotter water to \015\012ensure a clean load of dishes. ... Frigidaire PLD2855RFC Dishwasher

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a


If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

I have a stainless steel Kitchenaid dishwasher and the door drops hard when I open it instead of requiring you to push it down if you want to open it fully. Seems like a spring is broken. Any ideas?


There a good chance the springs popped\015\012or the ropes came off the pullys take off the toe kick and peek in on the edges you should see exactly whats going on ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

INSULLATION BLANKET Today I had two KitchenAid dishwashers installed. The installer took the insullation blanket off and told me that it was not necessary. He did this because the dishwashers did not fit under the counter with it on. I bought these dishwasher because if had a 51 Db rating for sound. They are noisy. Is it possible that this wrap around polyester foam like blanket actually helps decrease the sound?


Get his **** back out there. ... Dishwashers

Kenmore 16359 this ca12. i saw your solution and thanks but i have a question before i change the console. the machine was working fine and we went on vacation and when we came back that is when the light was blinking. could that have caused it or does the consoles just go out? i would like to know so when i repair it i don't break it again. i looked at the possibile fixes prior found the console but not clear if the circuit board comes with because the circuit board in no longer availible. is i


'Membrane buttons' as they are so called, just go bad. The circuit board is not part of the switches. circuit board not available? Chances are this part has a substitution that is available. Many models of this type have consolidated to 1 or 2 standa ... Kenmore 24 in. 16539 Built-in Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

My Kitchenaid KUDS01FLSS3 dishwasher is making an unusually loud whirring noise when it is in the wash mode. I am fairly mechanically adept, I like to get some ideas on what to look at so I can fix it and quiet it down.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

HE error My LG LD-14aw1 is showing HE error code - Heater Circuit is troubled???. (Not as much as owner!!!). I have repaired several dry solder joints in the control module, which have been causing various operating failures, but the HE problem has got me stumped. Can anyone provide me with a wiring diagram of the machine and or the control module? I'd like to trace the heater circuit to see if I can find the fault. Many thanks


From the manual: Errors: HE: Heater circuit failure.Please call your Authorized Service Center or LGECustomer Service at 1-800-243-0000(US), 1-888-542-2623(Canada). ... LG 24 in. LD-12BW5 Free-standing Dishwasher

DD603HSS Hi from France. i'm the owner of F&P dishdrawer DD603HSS for 5 years and half. (New Zealand made) yesterday, the top drawer looks with no power, no lcd , nothing. like no power alimentation. as you know, for a 5&1/2 years appliance, there is no more warranty... have you any idea for the cause of this trouble. is there a fuse and the location of this one ? i know each drawer is autonomous, then i suppose each drawer is protected by a fuse. - i precise "The bottom drawer works fine".


There is only one power supply or input so you need to find out where the power stops from the bottom to the top drawer ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

The inside of my stainless steel dishwasher looks as if it has a white film on it. My glasses are also looking like they are etched. I haven't changed the dishwasher soap...any ideas what is causing this? The dishwasher is about 4 years old, and we've only noticed this in the past few weeks.


Are you using a rinse agent such as jet dry( you should be) and if your using tabs with rinse aid built in dont add extra rinse aid to dispensor, . water temp might be an issueperhaps some detergent has gotten into the rinse aid compartment mistakenl ... Dishwashers

The door on my built in Frigidaire dishwasher is falling open. it seems like a spsring or something has broken. I am looking for a repair manual, possibly an exploded diagram so that I can see what parts i might need. Thank you, Brenda


Here is the way the springs hook up.\015\012\015\012\015\012Here is the break down.\015\012 ... Frigidaire Dishwashers

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Our Asko D1716 dishwasher functions to fill and empty but the pump which causes the sprayers to rotate and distribute the water does not function. The local appliance repairman diagnosed the problem as a bad pump (he called it a motor). Since the pump is a $400 part plus labor, is it possible that the problem is something else like a bad motor capacitor or relay? When the cycle calls for the pump to come on, there is no sound except for a very soft hum.


Hi ! \015\012\015\012Got a D1706 ( in 2002 ) paid $1000 and as os April 2010...same problem as yours, I will trow it away ( dishwasher ) and will never buy at such cost. I'll get a GE or LG. \015\012\015\012Stupid Sweden dish ... Asko D1716 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1275 seconds