Having problems with your Dishwashers ?

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


Answers :

HI,

Just visit this link HERE and your problem will be solved.

Goodluck,
Please don't forget to rate the solution.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

'Dead' DU1100XTP The dishwasher will not start - no lights at all - no indication that anything's working (although I confirmed the unit has power). I've seen numerous posts regarding the control board - is there a problem with these in general? My unit is just beyond the warranty (naturally!) so I'd like to know if there's been any concession made by the manufacturer due to the number of problems. I'd gladly replace the board if Whirlpool would send me one. Thanks.


This may sound simple but... make sure its plugged in all the way. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

I have a maytag performa dishwasher. It will not turn on. The pushbutton control lights just flicker. Would this be a problem with the pushbutton control or the control circuit board?


... Maytag Dishwashers

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Our LG Model LDF6810ST Dishwasher (2 years old) does not heat water any more. Dishes do not get clean and do not get dry. I do not get an error code. I assume I need to replace the control board OR heater assembly. How do I determine how to solve the problem?


It cleans poorly ------\015\012\015\012\015\012\015\012\015\012Water-inlet valve\015\012\015\012Most cleaning problems are caused by the dishwasher not getting enough wash water, so the water-inlet valve is often to bl ... Dishwashers

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene


... Kenmore Dishwashers

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

We are on the mainland but our dishwasher is on the island of Maui. We are told that the main control board is out. The dishwasher is only about 4 years old and is used only about 4 months out of the year. Is this a commmon problem with Bosch dishwashers? Is there only one "Main" control board? If so, do you know what the part number is? thank you.


... Bosch Evolution 800 SHE58C02UC 24 in. Built-in Dishwasher

Installed a new control board in GE dishwasher: GLD6860NSS. Still having problems!


... GE GLD6860NSS Stainless Steel Dishwasher

I have been interacting with Daniel about my Dishwasher Smart Dispenser problem. The last thing he had to say to me was that I needed to replace my drain pump. Before doing this, I would like an explanation of why a new drain pump will solve my problem since my dishwasher is draining just fine...it is my Smart DIspenser that is clogged up and not working ?? See the discussion here: Dear go4t9ers, There is a new Comment for the I would like to run the Smart Dispenser Purge Solution on


Ok first this is the schematic for your entire machine http://www.s ... Dishwashers

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Model: Whirlpool ADP 4501/5 (4 years old) Problem: Dishwasher won't start wash cycle. Green light flashes 11 times. After adding a bucket of water to the dishwasher it runs normally. Checked the inlet valve and it appears to be fine. Filled the salt container and it solved the problem for a while but having the same problem again. Any suggestions would be appreciated.


... Dishwashers

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

Zanussi Dishwasher ZDT6053. Holding the On/Off button causes the indicator lights to work correctly, but as soon as you remove your finger from the spring loaded button, all the lights go off. Would guess that on/off button should electronically latch via the control board. Have removed mains power for 60 secs in the hope of a 'hard' reset, but no fix. Is there anything obvious to check or fix or must it be a replacement control board?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Hi got a baumatic dishwasher bkd62ss.1 model, it gets half way between the last cycle and cuts out and blows the circut board switch, can turn dial and wee bit and re switch circut board and away it goes again. what would be causing this problem. had dishwash for about 3-4 years? thanks


... Baumatic Dishwashers

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1670 seconds