Having problems with your Dishwashers ?

We are having water leak from the bottom of our Roper Dishwasher door. THe model # is RUD5750DG3. I have taken the inside door frame off and found a small white rubber seal had dislodged inside. i placed it back in the only sopt it fits but water is still leaking. I have checked to make sure the water is not leaking from any where else on the dishasher. This occurs when the water inside is spraying and eventually fills up on the bottom. We no longer have our manual as the dishwasher cam


Answers :

Try to fix the rubber seal which has come out by fixing it through super glue or apoxy seal which will stop the water spill and leakage.
\015\012Please give more details of you dwasher ..... the Make and model so that i can send you the manual for future use
Step 1:
Remove the service panel that runs along the front of the dishwasher just below the door. If it is screwed in place, remove the screws with a screwdriver. If the panel hangs on hooks, pull the panel out and swing it up to remove it from the hooks.
\015\012Step 2:
Check the end of the drain hose that connects to the dishwasher. If it's leaking, tighten the clamp with a screwdriver.
\015\012Step 3:
Check the drain hose connection to the kitchen sink drain. Again, if it's leaking, tighten the clamp with a screwdriver.
\015\012Step 4:
221_a1.jpg Check for leaks around the water-inlet valve. If necessary, use an adjustable wrench to tighten the compression fitting that connects the water-supply line to the valve. If the fill hose is leaking, replace the spring clamp that is on the hose with a worm-drive hose clamp. It produces more clamping pressure. Use adjustable pliers to compress the spring clamp so you can pull the clamp and hose off the valve. Remove the spring clamp from the hose. Buy a worm-drive clamp at your hardware store, then install it and tighten it with a screwdriver.
\015\012
\015\012Leveling the machine\015\012Step 1:
Remove the front access panel (see step 1, "Tightening the fittings"). This will give you access to the dishwasher's adjustable feet.
\015\012Step 2:
Open the door completely and remove the bottom dish rack.
\015\012Step 3:
Unscrew the dishwasher from the kitchen countertop so the dishwasher can move freely as you adjust the feet.
\015\012Step 4:
Check to see if the dishwasher is level side to side. Place a small level inside the dishwasher so it's sitting on the bottom pan and facing parallel to the front lip of the dishwasher. If the dishwasher is not level, use adjustable pliers to turn one of the dishwasher's front feet up or down until you hit level.
\015\012Step 5:
Check to see if the dishwasher is level front to back. Turn the level perpendicular to the door, and place it on one of the bottom ledges that run along the side of the cabinet. Check the level again. If the dishwasher isn't level, use your adjustable pliers to turn the back feet up or down until you hit level.
\015\012Step 6:
Reattach the dishwasher to the countertop and reinstall the front access panel.
\015\012
\015\012Fixing a leaking door\015\012Step 1:
Inspect the door gasket. As it ages, the gasket can crack or become hard, preventing it from sealing completely.
\015\012Step 2:
If the gasket appears solid, adjust the door latch so the door seals tightly. Loosen the screw that holds the door latch to the cabinet. Push the latch in slightly and retighten the screw. Test the door and readjust the latch if necessary.
\015\012Step 3:
Replace the gasket if water continues to leak after you've tightened the latch. Most gaskets are held by compression in a groove on the door or on the dishwasher cabinet.
\015\012Step 4:
Pull the old gasket out of its groove, using adjustable pliers (see illustration). Take the gasket to an appliance store to get a replacement.
\015\012Step 5:
Soak the new gasket in warm water to soften it, then press it into the groove. Start at the top, then work your way down the sides and across the bottom.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We are having water leak from the bottom of our Roper Dishwasher door. THe model # is RUD5750DG3. I have taken the inside door frame off and found a small white rubber seal had dislodged inside. i placed it back in the only sopt it fits but water is still leaking. I have checked to make sure the water is not leaking from any where else on the dishasher. This occurs when the water inside is spraying and eventually fills up on the bottom. We no longer have our manual as the dishwasher cam


Try to fix the rubber seal which has come out by fixing it through super glue or apoxy seal which will stop the water spill and leakage.\015\012Please give more details of you dwasher ..... the Make and model so that i can send you the manual f ... Dishwashers

I have an LG LDF6810ST dishwasher that has a leak on the bottom right hand side of the door. It appears to be leaking from inside the door itself. The dishwasher is 2 years old. I checked the inlet water to make sure connections were not leaking and they were not. I live in a rural part of Alaska so after talking with the LG help desk I'm pretty much on my own. Any ideas?


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Do4esnt clean My Bosch SHX33a05 dishwasher has a problem. It fills and drains well but nothing gets clean. It appears as if the arms are not rotating but the inside is wet when I look inside. I have put a bit on catsup on the inside door and even that is on at the end of the cycle. I have opend and clodes the door multiple times during the cycle and bot arms appear to not be rotating. Nothing is blocking them. I have clean the microfilter, the drain screen and open up the impeller to make sure t


... Integra SHX33 Dishwasher

The dishwasher detergent is not dissolving. There is rinse aid in the dispenser - sometimes the door opens and the detergent comes out and sometimes it doesn't. If the detergent does come out then it is just sitting in the rack - should it drop to the bottom of the dishwasher? I have checked the door cleaned out around it to make sure the hook and release are working. I opened the door and the water is hot.


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

Dishwasher is making a clicking/grinding sound from what seems lower left area of door Not sure if the model number is correct below, but it is a built in jenn air dishwasher, control buttons on inside of door top.


... Jenn-Air JDB3610 Built-in Dishwasher

Soap has collected and hardened inside dishwasher and comes off and flakes on the dishes. I have tried cleaning with a few cycles of 1 cup vinegar (no dishes) and making sure the water is the hottest. I also tried Dishwasher Magic which did not help at all. Can I use Lime Away? Is that safe? Or will that poison me with the next cycle of dishes? Is there another solution? Thanks, Missi Walkyourbike


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Kenmore 24 in. 16039 Built-in Dishwasher

KENMORE DISHWASHER Hi, My husband just received a reset "code" for our dishwasher and the light went off and we thought it was going to work. But now no water is going in, we can hear it making like a humming sound and its warm inside when we open the door. Can you guide us?


You probably have a build up of food under the bottom heating element. The excess food falls to the bottom and then clogs up the space where water collects to be heated. The heater works but there is no water to heat, so washer will go on to next pha ... Kenmore 24 in. 16019 Built-in Dishwasher

I noticed water leaking underneath my dishwasher through the floor joists to my basement. It was a small but steady drip through the joists. I turned off the water to the dishwasher and the leak stopped. I looked inside the dishwasher and there is still some standing water inside the dishwasher, but I cannot see anywhere that water is standing under the dishwasher. I am wondering if the leak is at the pump or at the door? But I see no evidence of the seal leaking.


This is probably the line that goes from the water inlet valve on the bottom of the dishwasher up to the valve leading into the dishwasher itself. It is probably a black corrugated rubber line. This is an extremely bad design, but the solution is s ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

I have a Kitchenaid dishwasher model KUDS01FLSS2. I finished replacing the door balancer cord and started the dw up and it started leaking underneath from the bottom somewhere around the middle of the unit. This is when it first enters the cycle, so there is no water inside. I pulled the DW out and look at the hoses and components under the DW and all looks in good shape and could not detect any cracks. However noticed that one of the hoses (not sure what the hose is called) that connects to the


In this Kitchenaid dishwasher model KUDS01FLSS2, the whole motor and water pump assembly simply sits (I think loose) in the bottom of the DW. From the inside, it is the round mechanism where the sprayer is mounted above the chopper, all one piece sit ... KitchenAid Dishwashers

My dishwasher is not rinsing the soap of the dishes or even soap is dried down the door. It has been going on but now all the dishes have dried soap on them. I have been making sure that the water is hot enough. Thanks


... Maytag 24 in. PDC3600A Built-in Dishwasher

Our dishwasher is not filling with water, when the front door is opened the pump is still making a noise, the inside is hot


... Siemens 24 in. SE25A091 Hi-Line Free-standing Dishwasher

There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t


Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers

Door leak I have a small leak between the bottom of the dishwasher door the lower service panel on the dishwashere. I did replace the seal on the inside bottom of the door along with the other parts that come with the door seal. Could there be a gasket leak around the detergent dispenser or the vent at the top of the inside of the door. I did not check the water lever as was mentioned in a previous question on water level, but the float does move up and down quite freely. Any suggestions as to w


I had my dishwasher leaking alot at the bottom of the doo,r and found out that the steam vent was very cloged with gunk. After taking the vent cover off on the inside of the door and cleaning, then putting the vent cover back on NO MORE leaking. Th ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

I have a built-in Bosch dishwasher SHU 4302 UC. It no longer drains the water out at the end of all the cycles. I have tried everything mentioned in the booklet (make sure water is hot, use the jet-dry stuff, make sure outflow hose doesn't allow water back in). I have to siphon out at least a good bucketful of water. (Also, only the regular wash cycle works, which is fine with me.)


The problem is a solenoid on the bottom of the unit. It is a small black cylinder next to the pump. It operates the valve that changes to the drain cycle. You can probably order one from Bosch ... Bosch 24 in. SHU43 Built-in Dishwasher

Is it common for Kitchenaid dishwashers to have water pooling inside them? It's almost like the valve for water coming in isn't shutting all the way...in the middle of the day, we'll find water inside the dishwasher...it drips out the front when you open the door...but when you turn it on, it doesn't have any problem draining the system...mysteriously, we find water in the bottom...what's up?


There is a rubber flapper valve that keeps water from running back into your dishwasher. It's a $5.00 part, but it's a bear to get to,\015\012\015\012You have to pull the drain pump to access this flapper.\015\012\015\012Also ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

I need the diagram for the door pulley system so I can make sure I am hooking it up right. The original door chord/pulley assembly broke. I ordered new parts, Now I want to make sure I am putting it back together the right way. The edge of the screw- on floor panel is pushing the plastic hook off of the door hook when you shut the dishwasher door.


... KitchenAid Dishwashers

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

It appears that the dishwasher is not getting enough water. I have made sure that there is nothing blocking the door area so that the soap can dispense and I have reduced the amount of detergent to maybe a 1/2 Tablespoon. Have tried both powder and liquid detergents. Ran a sani clean cycle with the Jet Dry product for dishwasher used in the rural. I also run the hot water in the sink prior to starting the dishwasher to ensure the water is hot when it comes into the dishwasher. The detergent


Hello,Welcome to FixYa.Based on your description you`re experiencing the ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

My 5-year old Bosch dishwasher leaves a somewhat fine grit on dishes? especially obvious on the inside of glasses. I use only Cascade detergent, use a rinse aid, don't overfill the machine, and always make sure that the filter at the bottom of the dishwasher is clean. I also make sure that the spinner is able to move freely. But, after all of that, I sometimes get very clean dishes; even more often, not. I see no rhyme or reason. I am presently looking at an entire load that has gone through


I have the same problem with mine!! It's 6 years old, and I'm running loads of dishes through twice. Even that doesn't help! And I rinse the dishes too, so I have no idea where all these "crumbs" are coming from. Will check back for updates. Hope to ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2173 seconds