Having problems with your Dishwashers ?

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Answers :

Did not realise this is a washing machine and not a dishwasher.
\015\012
\015\012Looks like some consultant has already been dealing with you on this problem.
\015\012
\015\012Hard to say if it is a simple as an inlet solenoid valve or the control board itself.
\015\012
\015\012The whole machine is heavily electronics based - even the spin speed is controlled by the controller. Check these two parts out first. Refer this site.
\015\012
\015\012Refer this site for the actual availability of the parts.
Have you tested the door switch by chance? Those can cause problems. If it is shorted out, loose, wet, ect. It will cause the machine not to start.
\015\012Also, if the water pressure is not high enough or water temp is not hot enough, you will have the same issues.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.


Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

I have a Hotpoint Aquarius dishwasher (FDW60) The 3hr and 12hr lights are on and the machine won't respond to any other buttons pushed therefore I have not been able to reset the machine (that is if the delay start has actually been activated). It started with the machine not draining however I was able to drain it manually so that rules out any blockages. Please help...The manual doesn't have any troubleshooting advice for those lights... Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. When 3hr (Prewash) and 12hr (drying) light flashes it indicates\015\012the fault in the heating ci ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a whirlpool DWH B10W. Last week the main drain outside blocked and none of my service machines were working (not draining). The main drain has now been unblocked and every machine except the dishwasher are now working fine. The plumber has checked the drainpipes again and says all are now clear. When I try to use the dishwasher, after the initial drain it stops and starts beeping at me. I have also noticed that no water is going into the machine. What's happening?


The error most likely indicates a Long Drain Sequence (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. \015\012 \015\012 \015 ... Dishwashers

I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.


You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers

I got the pressure washer started - lots of smoke etc after not having used 3 years. I then poured in wrong oil to top it off - my brother's chain saw bar oil. DARN. After 3-4 minutes it started rattling and stopped. Can't pull the chord to get started. Did it seize the engine? I have drained all oil. Can I try using a cleaner, light weight oil to try to unlock it?


Nope! you have blown the seals and most likely the cylinder is full of water. You will need to take it to the repairer to have it cleaned checked and new seals fitted. $200 ... Karcher 1750 psi Electric Pressure Washer

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

KitchenAid 24 in KUDM0IT JWH0 auto test mode? Starts, fills, but doesn't wash or rinse, just hums, drains fine. There was **** in the screen with the chopper under the filter (clogged) a piece of glass got caught under there, I removed it, it worked fine until I removed the glass. I just did the auto test mode thing and it did some filling and then drained. Still not working though


... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers

Kitchenaid Dishwasher model # KUDS25SHBS1 has started making noise. Noise happens when unit is draining so perhaps its the same mechanism that houses the grinder. Can definetly hear a clicking as something spins around to drain the unit. I have removed the washing armature and plastic skirt around bottom and felt underneath the skirted area, but don't feel anything caught or jammed. Noise is getting louder as more draining cycles are being utilized (i.e. as we use the machine more). Anyone have


Looks like motor noise. Check the pump. ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Started in wash mode ,water in machine then stopped running.wont drain and start light just blinks


... Kenmore 24 in. 16039 Built-in Dishwasher

Our dishwasher seems to be stuck in drain mode. My daughter put the wrong kind of soap in it. She accidently put Regular dish washing soap in rather than machine dish washing soap. We've got all the suds out. Seems to drain water just fine. However we cant seem to get it to add water. Does the soap have anything to do with it? Anything I can do from my end? Please Advise. Thanks


Plastic base is full of water. Need to remove whole unit to access bottom and dry it out. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have the karcher k2.90m and i was using it and it started to leak oil after about 40 min of use, i think it might be because i got some water on the machine but not sure


... Pressure Washers

I have an older Maytag model #WU482. For some reason it will not drain and will only run using the economy mode. I can hear the timer ticking at all other cycles and it does click between cycles. I recently replaced the drain float and the machine had been working fine after. The motor is working and the belt is good. I think the kids were playing with the timer knob. Could this cause a problem with the timer motor? Or does this sound more like a pump out issue, impeller? I'm thinking its


First,inspect the drain float. Make sure it rides on the micro switch correctly or it will not take on water.Check the float micro switch for continuity. Check for power at the water valve when it calls for water. Remove the wire harness from the tim ... Maytag 24 in. PDB1420 Built-in Dishwasher

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

This is a top loader machine with no transmission and every 20th load starts chirping and throws water over the top of the tub ge wont admit problem but i got six that says diffrently machines have had new motors and mode shifter


Hi,\015\012 \015\012A chirping noise means that the motor bearing wear. This can also be checked for by taking the belt off and running the motor alone. The spilling of the water is a result of the drum rot ... GE Nautilus 24" Built-in Dishwasher

I have a Coleman powermate clean machine pressure washer 2500 psi 2.36gpm and has a 6x200 honda 6.5 horse motor. I just bought at a garage sale.It started just fine when I got home and in less that 2 minutes quit. It says the engine will stop automatically when low on oil. what kind of oil should I use and for the pump what kind of oil do you use?


... Coleman Pressure Washer PW0881800

Hi, Zanussi dishwasher DE6344, when starting any program the machine start pumping (draining) for a while and then stops, lights start flashing saying that the draining is faulty. Checked the drainpipe and when adding some water the machine drains it perfectly, still the program won't start. Looks like it thinks there still water inside ? Suggestions ?


... Zanussi 24 in. DE6544 Built-in Dishwasher

Havnt used my dishwasher in 2 years on account of saving water. now when i push the start button some water flow into machine for a few minutes and then just stops. manual says to clean filters and drain pump but all clear. what is next plan of action?


Try pouring water from a bucket through the front. maintain the level. It should not overflow.Run a empty cycle. If there is a air block it will get cleared. ... Asko 24 in. D3120 Dishwasher

I need the steps to change the hose assembly on my Whirlpool portable dishwasher. When I got it someone had cut the sink connections off so my son connected it to the water and drain with my washing machine which was in the kitchen. However, I have moved and want to use it as portable. I purchased the new hose assembly for the sink faucet, I just need instructions on how to take the dishwasher apart and connect the new hoses.....HELP PLEASE!


... Whirlpool 24 in. Portable Dishwasher Dishwasher

GE GSD4320Z00BB dishwasher drain pump not pumping down machine during normal cycle. The pump does work using test mode, therefore not a pump problem, no clogged lines (confirmed) what else could it be?


... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1361 seconds