Having problems with your Dishwashers ?

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Answers :

Hi,

This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder than it is used to getting.

Repeatedly press the Heated Dry and Hi-Temp Wash(scrub) which ever yours has until all the LED lights come on, press cancel twice and\015\012try the dishwasher again making sure to run the water at the kitchen\015\012sink till it is hot before starting the dishwasher, if this trips and\015\012locks you have a problem with the heating element, or temp sensor.
Press\015\012the heated dry button followed by the normal cycle button, and then\015\012repeat once. You should see all of the lights come on for a second or\015\012two, and then the dishwasher will work again.
If you haven't\015\012already, take a look under the kick plate in front to see if there is a\015\012schematic tucked in there somewhere. Whirlpool has put their\015\012diagnostics for specific models on these.
I don't have the specific repair manual for you model.
So, if the above combination does not work here are two more that have worked for me.

HiTemp Wash + Air Dry + HiTemp Wash + Air Dry in less than 5 sec
or
Hi Temp Scrub/Scour + Air Dry + Hi Temp Scrub/Scour + Air Dry in less than 5 sec



Let me know, if you need further assistance.


Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

Kitchen aid dishwasher kudk031twho gets water, drains, soap will not disolve, runs thru all cycles, once the clean lite flashed 7 times, after reseting code never happened again.


... KitchenAid Dishwashers

My whirlpool ADP 8540 starts, fills, then stop and flashes 6 times, pauses, and flashes 6 times repeatedly, until I end the cycle. What is this error code for? Can I fix it myself?


6 Flashes means water valve is switched on but flow meter senses no impulses (less than 10 impulses in 10 secs) and the water indicator is at a low level. Water Valve Closed or blocked.\015\012\015\012Water inlet valve defective. Flow met ... Dishwashers

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

Kenwood kdw12st3a does not drain. Flashed e4. Emptied, cleaned filters and poured through boiling water. Not improved. Still water in bottom although did complete cycle without flashing error code that time. What parts could be faulty please? Am prepared to have a go at replacing if not too difficult. I note that I can purchase most parts from Kenwood etc. Many thanks!


... Kenwood Dishwashers

DISHWASHER QUIT WORKING IN ALL WASH CYCLES EXCEPT SHORT WASH CYCLE. YES I HAVE TRIED TO FIX IT. I HAVE REPLACED THE CONTROL MODULE WITH A NEW ONE. ALL WIRING LOOKS CLEAN AND IN GOOD ORDER. NO EVIDENCE OF CORROSION. NOW UNIT WILL NOT WORK AT ALL, BUT "CLEAN LITE INDICATOR' IS FLASHING IN SEQUENCES OF 7. I HAVE FOUND THE SCHEMATIC SHEET BEHIND THE KICK PLATE. AND USING IT I HAVE TRYED TO USE THE DIAGNOSTIC PROGRAM BUT CANNOT FIND ANY PROBLEMS. AFTER DIAGNOSTIC PROGRAM IS COMPLETE THE DI


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012With the symptom you`ve described ( specifically the clean lite ) this is an error of poor water circulation or a heating fault...many times manifesting in th ... Whirlpool Dishwashers

I get an E1 error code. If I check the water level it is low so if I put in about two quirts of water it runs for only that water cycle, then I have to put in another quirt for the next cycle. The water comes to the same level every time. Can you point me in the right direction?


Excessive RPM of washing motor happened during wash cycle due to water \015\012leakage.\015\012Possible cause: Water leakage in hose connections,water is leaked by \015\012damages. The motor water seal leakage of sump assembly. The height of \015\012 ... LG Dishwashers

My bosch dishwasher model shx45m runs for hours. It gets down to the last minute on the cycle time and then will not move on to the next cycle. The error code is 01.


... Bosch Integra 500 SHX45M0 Built-in Dishwasher

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

My lg dishwasher is running ok but i randomly get the LE error code. I noticed that when it runs the cycle it takes 3 times as long to run than normal. Is this the motor or the electronic panel. the wiring is ok already checked.


Motor might have something blocked in the coils. mine did the same thing and found a piece of plastic melted in the motor housing ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

It has been flashing an F2 error code and the timer starts at 65 then switches to "1" which stays on during the cycle. Now it will run for about a minute then stops completely. Can you suggest any parts that we can get to fix this?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The "F2" for Asko dishwashers indicates either the unit is overfilling, or the valve itself has failed.\ ... Asko 24 in. 1895 Built-in Dishwasher

My dishwasher will not start. The cecle time just keeps flashing, and the start button won't turn the cycle on. There is no error code, and the door appears closed properly


... Bosch Dishwashers

I have the kdw12st and recently it doesn't complete the wash cycle. An error code e1 flashes up at various times, not necessarily at the same point in the program.


Andy,\015\012\015\012First, heck for any leakage beneath and around the dishwasher.\015\012\015\012If you are certain there is no leak, confirm that the drain hose has a rise of at least 20 inches as it travels to the drain. Which is alm ... Dishwashers

I have a dishdrawer (2) and following the use of a dishwasher cleaner, the bottom drawer appears to have developed a blockage. It will not empty, gets to the pump out part of the cycle and shows the red error code F3, to which there is no reference in the trouble shooting guide. The top drawer has also developed minute leak, sufficient enough to leave dribble marks on the lower drawer and over time, a white deposit on the floor. Is there anything we can do for the blockage problem before reso


Remove the small basket from each drawer and lift up the removable plastic cover and take the drain filters out , empty them of food by products and try it again.. If you've never cleaned them then that's your problem with the drain process.. Hope th ... Fisher and Paykel Dishwashers

Smeg df612sdx Until last week I enjoyed several years faultless service from my SMEG Stainless Steel dishwasher, with the exception of needing to replace 2 x spray arms. The unit has now stopped working altogether. Despite powering up several times, I continue to get both the start/pause and selection programs buttons constantly flash (green lights) when the unit is switched on; previously this only occurred once the wash cycle was complete. Any thoughts would be most appreciated. Thank you


... Dishwashers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Kenmore elite 2 front loading washer model#110.45872400 It first flashed the code FH and then went to the running time is now flashing and it sounds like it is running but the cycle never starts and I cannot cancel the cycle by pressing pause/start two times. I have checked the water lines and the screens and cleaned out the drain catch below. what next


... Kenmore Dishwashers

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

My Whirlpool ADP 5406 runs for about a minute and then the light flashes four times, repeatedly. What can I do to fix this? (I can still get the machine to run its cycle by holding down the start button, but the light will flash four times again on completion).


Hi and welcome to FixYa. I am Kelly. \012 Usually this symptom also shows an F7 error code. You will need to remove the lower wash arm (NOTE INSTALLED POSITION) Also you will need to remove the metal grate under the wash arm to ... Dishwashers

I have a Bosch SHU5316UC dishwasher. The last two times it ran, my wife says the display said "CL" (for clean) after running through the cycle, but she heard a "motor running" until she opened the dishwasher. Attempting to run the dishwasher tonight, it won't start - it displays a "P" (error code?) when you attempt to start it. Can you tell me what the error code P is? Thanks, Dave


P stands for program in computer algorthms. The device displays program whenver chages were made to the default settings. A powered on devices least has malfunction only requires reseting to attaon default features. Depending on the type of device, r ... Bosch SHU5316UC Dishwasher

Intake drain flashing - but this time because water is not filling. Checked voltage at controller board - inlet solenoids are getting 120V intermittently. I found online that this is the behavior for fault code f12. But my machine does not give fault codes directly - is there a way to get it to "blink" them?


... Miele 24 in. Incognito G843Vi Built-in Dishwasher

2006 kenmore elite dishwasher 665-17263402- the clean light flashes 7 times , pauses then flashes again 7 times. What does that code mean? Cannot get washer to operate.


The blinking "clean light" is a common problem with some of the Kenmore and Whirlpool models dishwashers. The problem is usually attributed to water supply temperatures being too low when filling. Apparently, there are some issues with th ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

We have a Kenwood KDW8ST2A dishwasher. We used to get the error code E3 (when still under warranty) and were told not to use dishwasher tablets as it generated too much foam. The problem has been intermittent but now we get the E3 error every time, no matter what program we run, or how little detergent we put in. I've a feeling its not heating up properly, is there any way to check the heating element? Is it worth attempting a repair?


... Kenwood KDW243A Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2052 seconds