Having problems with your Dishwashers ?

I have a triton xl model @ gsd6200g00bb serial #va790400b. The dishes on the top rack are not getting clean. I have removed the top, and middle, and bottom arms cleaned calcium out of them. Removed the screen below the lower arm cleaned. The top and middle arms are still not spinning during wash cycles. Where do I go next?


Answers :

Apart from the spray arms themselves there could be other reasons why the water is not getting up to the middle and top arms.
\015\012
\015\012The distribution circuit from the wash pump that feeds the arms could be blocked or the wash pump itself is not developing enough pressure to push the water up. I am assuming the dishwasher is taking in water at the start of the cycle and you can see water at the base.
\015\012
\015\012The distribution circuit to the middle and upper arms can be viewed in this diagram.
\015\012The part 585 carries the water up from the wash pump circuit
\015\012
\015\012The wash pump circuit s shown in this diagram.
\015\012The pump is part 310 and the water is distributed to the upper arms by part 450.
\015\012
\015\012Your dishwasher has got a turbidity sensor which checks if the wash water is dirty. If so, it drains the water out during wash cycle and lets fresh water in. A reason for not enough water circulating in upper arms could be the drain is happening faster than the inlet water is getting in which can cause a nett drop in water circulating in the dishwasher. Question - do you hear drain pump running when the wash is also happening?
\015\012
\015\012Hope we can solve the root cause of the problem.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a triton xl model @ gsd6200g00bb serial #va790400b. The dishes on the top rack are not getting clean. I have removed the top, and middle, and bottom arms cleaned calcium out of them. Removed the screen below the lower arm cleaned. The top and middle arms are still not spinning during wash cycles. Where do I go next?


Apart from the spray arms themselves there could be other reasons why the water is not getting up to the middle and top arms.\015\012\015\012The distribution circuit from the wash pump that feeds the arms could be blocked or the wash pump ... Dishwashers

I have a whirlpool GU2700XTSQ1 dishwasher. I have the typical top rack not cleaning problem. I have removed the rear washer tube that leads to the top sprayer, no clogs. Upper arm is clear, lower arm is clear. I also removed the lower cover, checked the chopper screen and inlet, no clogs. There is a screen inside that I cannot get to. It appears to have some sort of paper or cloth sticking through the screen with a 50% block. Perhaps a sticker or label from a dish. I see this screen when looking


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Hello, Please help. I follow recommendations for cleaning: sewer pump, cleaning arms, screens of the dishwasher. However, still machine is not working. water is not going through arms: lower, middle or top. Also, I get water into dishwater when it starts, and when I open i hear noise for water dripping into hot elements,but no water is running throughout. PLEASE HELP


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Dishes all cloudy and spotty. Maytag Intellisense plus 1996 dishwasher. I have real hard water that leave white calcium build up. I can remove and clean all of the lower spray arms and filter. How do I remove top spray arm to remand remove deposits? The motor sounds good, hot water, fill ok. On the inside top of center of arm where it meets the center input connection there is gunk to remove. How do I get to it? remove arm? thanks


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Danby 22 in. DDW399 Free-standing Dishwasher

Upper spray arm is not turning and I don't think water is coming out. Dishes on top are not coming clean. Dishes on bottom are clean (as clean as they get with this dishwasher). How do I remove upper spray arm. Also I'm not sure how to remove lower dish rack to access upper spray arm. Any help appreicated. Kitchenaid model KUDP01FLSS5 Chris


Hi Chris,It sounds to me like a restriction in the pump. I put together some information here on cleaning it out. If you try these please give me some feedback as to if they help or not.Thanks! ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

I have a frigidaire dishwasher - model number PLDB998AC1. There are two spray arms in this dishwasher - lower and upper. The lower works fine but the upper spray arms are not spinning. There is what I think adequate water pressure coming in from the top but no movement on the upper spray arm. Here is what I know: 1) The water pressure and spray arms alternate between top and bottom. 2) The upper spray arm moves freely when I push it gently. 3) I have removed the pump and cleaned out an


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

How do you remove the screen bolt from a Maytag MDB4261AW dishwasher? I got the arm off, removed the torx bolds, and can't figure out how to remove the middle bolt to remove the screen and clean out the drain.


... Maytag MDB4621AW Built-in Dishwasher

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

I have a whirlpool GU1200 dishwasher. There is a screen in the pump inlet which is located in a sump below the lower spray arm. It is getting plugged and needs to be cleaned, but I can't get the lower arm off. How do you remove the arm and shield to expose the screws to open the sump?


Hello....My name is Keith.....Please give me one moment while I bring up the parts drawings, and then I will start to address the issue.\015\012Thank You....\015\012 ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

I have a whirpool Quiet Partner III, and the top layer of glasses is not getting clean. I had a technichian out some time ago, and the problrem was caused by food debris trppaed in the filter in the wash module. He saud it was easy to clean that out, so I have removed the lower spray arm, but cannot undo the 4th screw that will allow me to take the grey round filter cover off to remove the food or paper debris. It is under the white flat pipe that delivers water to the wash module, and I cannot


I had same problem, would not clean well and fixed it. . I cracked open the door during wash cycle and used screwdriver to defeat the door lockout. The water from the bottom sprayer was only shooting half way to the top of dishwasher. To fix I remove ... Whirlpool Dishwashers

Dishwasher Problem... Hey, I'm sorry I can't seem to find this information anywhere else. I'm having a similar problem with my dishwasher (also a kenmore quiet guard) and I wanted to try to clean the filter. I'm not sure how to remove the lower arm of the dishwasher. There is a kind of plastic-screw in the middle of the lower arm, is that what holds it on? I'm afraid to try twisting it because I don't want to break it. How did you get it off of yours? I hope I'm not bothering you! Thank you, Je


You are right. The plastic screw needs to be removed. I have a Quiet Guard 4. My procedure is as follows:\015\0121. Remove baskets. Need to pop off the 'keepers' at the ends of the top slidding shelf supports.\015\0122. Remove bott ... Dishwashers

GLD4050 DW won't pump out at any time during wash cycle. Removed lower arm, screen, etc. and washed and cleaned out everything. Removed drain hose and cleaned it out. Reinstalled and ran again. At no time during he cycle does the water pump out. HOWEVER, if I put my hand on the drain pump I can feel and hear the pump running as usual at the right times in the cycle. What else could be preventing the pump out? Thanks!


You could have a plugged pump itself or broken propellers as long as drain and screen are clean which looks like you already took care of that. ... Frigidaire GLD4050RHS Builtin Dishwasher

Makes grinding noise.spray arm on top not moving. spray arm on bottom barely moving. grinds when draining too. removed and cleaned out holes in bottom spray arm, didn't help, but found piece of black plastic/porcelain with rust on it in the lower spray arm that looks like it may be part of a bushing?


Very possible that it is a fin off the impellers or could be a bushing ... Dishwashers

Dishwasher rotating arm and middle spout do not work since I removed screen at bootm to remove gunk. Easy to get off, but I must have put them back together incorrectly, please help. Dishes not getting clean.


There is a very good chance the rotating arm and spout have become clogged also. Remove the 2 components and clean out the holes to clear blockage. ... Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

My Maytag MDB7130AWB dishwasher is leaving detergent residue on the dishes. I removed the lower spray arm and filter screen. The screen was very clean with no mineral build-up. What could the problem be?


This is going to be more of a problem as the dishwasher detergent manufacturers are removing phosphates from dishwasher detergents. You can buy phosphates (or STTP) from various sources on the internet. It's called Sodium Tripolyphosphate. It's about ... Maytag Dishwashers

The dishwaasher was not cleaning. the top and middle spray bars seemed starved of water. I removed the lower spinner and covers until I got to the pump cover and can't see how to remove the cover. I found bits of food and junk that were stuck on the intake. How to I get the pump cover off? I have found one screw but can't see how the clip in released.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Kenmore 13732 / 13734 / 13739 Dishwasher

DD602I USA v2. Runs approximately 10 min then beeps continuously and on the front panel the middle light is red and on the inside panel the "Del" "Fast" and "Rinse" lights are red. What is this fault code indicating? I have made sure spray arm, impeller assembly, are clean and not blocked. No kinks in drain line. Induction motor sounds a bit noisy. This is only a problem with lower drawer, top drawer works fine. Thanks, Keith


... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Top level glasses, dishes, etc are covered in gritty substance after wash cycle. Lower level all dishes end cycle sparkling clean. I have removed and rinsed upper water spin arm. Am also using a rinse agent and still have this problem. Bosch model SHE45M06UC/50.


... Bosch 24 in. SHU5305UC Built-in Dishwasher

Ld-1416T I have an LG LD-1416T dishwasher and the lower spray arm does not turn. The top arm turns and the top rack is washed well. I pulled everyting out and cleaned all the filters (which weren't that dirty) but still no luck. I could only get so much stuff out to clean before it looked like to go any further, I would need to gain access through the bottom. Are there more filters in the motor area which might need cleaning? I read that it could be the vario motor. Can I test this? and if s


If you have one spray bar working then there is enough pressure. There is only one pump. So you should check the spray bar to see if it is plugged. Also check the seals to see if they are bad. ... LG Dishwashers

I have a Whirlpool GU2455.... dishwasher. Top spray arm is not spinning. Lower arm appears to be moving but slowly. Dishes on the top rack do not get cleaned. They are wetted, but the arm doesn't appear to be moving to allow all of the dishes to be cleaned.


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore BuiltIn Dishwasher Stock 17512 Model 17512200 Type 575-0 Serail FM3309375 Probelm: Water sprays out of lower arm weakly, and not out of upper arm at all. Action taken: Unscrewed the 4 screws holding down the item underneath the lower spray arm, and then the small item under that. Found major refuse from years gone by, removed, cleaned. Reassembled, same issue. I suspect I have to get 1 more level down, to the intake for the pump? found 2 screws to remove, but was not suc


... Dishwashers

Miele dishwasher G2870 scm. There is an F14 fault. I have cleaned the arms removed the waste basket from the bottom of the dishwasher and removed the two parts one with the large metal ball to expose the plastic wheel clog. There does not appear to be a blockage. I also removed the top arm and cleaned that out. I don't know what other inlets to check as the guide does not tell me exactly what an F14 fault is but explains F11,12,13. Can you help?


F14 on your model of dishwasher is indicating a blockage, poor water\015\012pressure or could be a fault with the pump pressure level switch or\015\012circulation pump.Filter and non return valve is cleaned of any blockages and if the fau ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1366 seconds