Having problems with your Dishwashers ?

Hi do you cover advice on Diplomat diswashers? I understand they are Whirlpool products rebranded. I have an F4 code fault that comes up mid cycle on an 8332 model


Answers :

Greetings,
\015\012 this is a drain fault code..I would suggest to clear out the sump and check that no one has replaced a disposal and forgot to knock out the drain plug...check for blocked drain hose...
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi do you cover advice on Diplomat diswashers? I understand they are Whirlpool products rebranded. I have an F4 code fault that comes up mid cycle on an 8332 model


Greetings,\015\012 this is a drain fault code..I would suggest to clear out the sump and check that no one has replaced a disposal and forgot to knock out the drain plug...check for blocked drain hose... ... Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Kenmore Elite dishwasher won't finish cycle. I have the same model, problem, symptoms, and fault codes as in thread: http://www.fixya.com/support/t7120066-kenmore_elite Model: 630.16303401 Fault code: H The water at the faucet is hot: 120F I pulled the control board and all the solder joints looked good--there were no signs of burnt solder joints, missing solder, cold solder, etc I measured the current on the grey-black wire at less than 1 (one) amp when the t-shoot says it should


Hello\015\012& Welcome to FixYa\015\012\015\012If\015\012the water inlet valve is fine then it can be a shorted wire or the heating\015\012element itself that is bad and needs replacement. Please get back to me if you\0 ... Dishwashers

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Model#lds5811bb--started making noise coming from the water inlet area(bottom left). 3/4's of the way through the cycle, noise became louder and then an error code "le" came on. We tried turning breaker off, then we tried in the rinse only cycle, but 5 minutes into it the "le" code error came on again. I'm fairly handy, so I'm not sure what part I can replace to maybe solve the problem. I can't afford to spend a couple of hundred dollars for a repair man to fix it. I'll appreciate any suggestion


The LE code is a locked motor code. Something may have gotten into the pump impeller. I would take the screens and filters off and clean the and check the pump for something stuck in it. It could also be the motor going bad but I would check the obvi ... LG Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

I have an LG dishwasher, model LDS 5811WW. Just after start up the error code "LE" comes on and the cycle shuts down. I have tried a couple of different cycles and they both react the same. Several other codes are found in the owners manual but not this one??


I'm just posting here to clear this from My Work Queue. There may be another cause for your code, but it only applies to certain serial numbers. If you want to know about it, do an ASK ME, otherwise good luck with your repair. Please don't bother ... Dishwashers

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


... Fisher and Paykel Dishwashers

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

Zsf 6171 On a normal wash cycle, my ZSF 6171 operates normally but comes up with a fault code ",60" then stops. Can you identify the fault?


... Dishwashers

My Electrolux 66010 dishwasher stops mid cycle with fault code 60. What does this mean? This code is not listed in the manual. Thanks.


... Electrolux Dishwashers

I have a Hotpoint LFT04 dishwasher which has now developed a fault. It runs and then stops mid cycle with flashing 2 and 4 lights as well as the power on/off button. Could anyone assist with the diagnosis as the manual does not help for this combination. From reading other similar models looks like heater or wiring fault?


... Hotpoint Dishwashers

Re Bosch dishwasher Fault code E02 There does not appear to be any heat being sent through the machine and certainly not when it comes to drying at the end of the cycle.


... Bosch Dishwashers

Serial #88445-B Rym 717881 model # fpdd 603 We are getting a fill fault code when we start the dishwasher. When the alarm goes off we have to pause the wash cycle open the door and then close the door if we do this about 2 or 3 times it will wash. It seems it fill with water but it seems to be low on water Dave Heller


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

On my model BKD 6255-3 DURING MID CYCLE RED LIGHT COMES ON AND WATER PUMP STOPS BEFORE CONTINUEING


... Baumatic 23 in. BDW13 Built-in Dishwasher

My Bosch dishwasher stays running in the wash cycle, will not shut down or dry and sanitize the dishes.Checking the fault codes both the power scrub and the reg wash lights flash. Model SHU33A02UC


A solution to this problem would be to sell me your dishwasher. The law \012firm for which I work is looking to acquire an old unrepaired Bosch SHU \01233 dishwasher for some ongoing litigation. If you (or anyone else with \012this model Bosch) could ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Top arm of dishwasher does not spin or spray. it is a 7 yr old frigidaire dishwasher, model #gldb957ab. The dishes on the lower rack also do not get clean. this just started recently. the mid level sprayer will turn by hand but doesn't move during cycles. seems like it would be there is no water coming to the top of dishwasher while it is running.


... Frigidaire 24 in. GLDB957A - Multiple Color Energy Star® Built-in Dishwasher

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Dead spot? We just moved into a house and the built-in frigidaire oven, model no: CFEB27S2AS1 bakes on only the low heats, 0 - 250 and high heats, 450 - max but does not heat (red indicater light not come on nor any heat) at mid-range. Is there something I am not doing, or does it need to be "rebooted", and if so how do I get to the power plug/switch as it is embedded in the wall?


Hello\015\012\015\012You said, We just moved into a house and the built-in frigidaire oven, model no:\015\012CFEB27S2AS1 bakes on only the low heats, 0 - 250 and high heats, 450 -\015\012max but does not heat (red indicator light not come ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Getting error code 0E on LD-14AW3 model dishwasher after 2 minutes. Checked drain hose and water seems to be coming out but won'y go any further in cycle Also makes a loud humming noise when running.


To little info, but looks like pipe is much to low. Not getting the opportunity to fill up properly.Raise it higher.(Im asuming that you can hear the drain pump run and water is being pumped out as wall. ... Dishwashers

Hi my whirlpool dishwasher (adp 6830) stopped mid cycle,no error code showing, will not reset with a long press to the start button (have prevoiusly been able to reset this way in response to f8 fault


... Dishwashers

WATER FAULT OUTLET CODE COMES ON ON ASKO DISHWASHER


... Bosch Dishwashers

Kenmore Elite Dishwasher 665.1315 fault code 61


... Kenmore 24 in. 15932 Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1333 seconds