Having problems with your Dishwashers ?

I have a frigidaire dishwasher (FDB1050REM2). When I start it, i heard water going in but when it is time to start washing it stops. I have found a burnt connection on the high limit thermostat. I have change the connector, but still doesn't work. Is the thermostat gone?


Answers :

Thermostat should not stop motor.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a frigidaire dishwasher (FDB1050REM2). When I start it, i heard water going in but when it is time to start washing it stops. I have found a burnt connection on the high limit thermostat. I have change the connector, but still doesn't work. Is the thermostat gone?


Thermostat should not stop motor. ... Dishwashers

High limit light goes on and unit shuts off about 20 seconds into start of cycle. Disconnected both wash and rinse heater elements problem continues Disconnected white wire at high limit thermostat problem continues disconect white with blue tracer problem continues whacked thermostat with pliers no luck whacked rinse heater thermo with plers no luck relay for rinse heater clacks and unit shuts down


Well, while I must admit that "Percussive" maintenance, sometimes works, as you have discovered there is more to servicing than, just "Giving it a good whack" lol.\015\012\015\012The problems with these units, is usually to do with the Thermost ... Jackson 25 in. TempStar HH Free-standing Dishwasher

Hobart AM14/1 free standing dishwasher with booster. Booster will not heat up beyond 41C. All three heating elements check ok with Ohm meter. High limit not tripped. Temperature screw up at maximum, when you turn the screw, you can hear thermostat click at lower temperature on and off. When turning on main power for dishwasher, heater in dishwasher works fine, but no relays click in the booster tank area. Have not checked for power at booster, have checked all fuses with meter and are ok. Ple


... Hobart AM14-253 Free-standing Dishwasher

First time it happen I notice that it started before it should with the timer, so started it without timer and it worked. Now its not going though circle again. Changing the program, and trying again, which did work first time but now it is not working.


1) you must test the timer is stuck with the contacts, you can try to clean it, tight loose wires, test wires open or break. Or doesnot replace complete TIMER. The timer contacts if you see the diagram is determinant control all operation machine of ... Hotpoint-Ariston LFT 228A 23 in Builtin Dishwasher

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

I have a Maytag quiet series 200, it been working fine since I purchased it last year, as of today I pressed start and it won't start and yet when I press the delay buttons of 2, 4, 6 it lights up and so do the other functions but to change my settings that doesn't work neither as well as my start button. Whats wrong with it? Any ideas? My model # is NY2222514


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

My dishwasher Kenmore 665.13462k902 worked fine for a little over a year, now it wont even start. At first, the high temp button wouldnt light, then no lights until you pushed start...tonight, nothing works...any help?


... Kenmore Dishwashers

My dishwasher Kenmore 665.13462k902 worked fine for a little over a year, now it wont even start. At first, the high temp button wouldnt light, then no lights until you pushed start...tonight, nothing works...any help?


... Kenmore Dishwashers

My pressure washer is bogging out and shutting off. It will run fine for a bit then it starts sputtering and shuts off. I changed the oil right before this started happening and yesterday i changed the sparkplug and it seemed to be working fine until I used it today on the driveway.


SOUND LIKE FLOAT IS STICKING ... Dewalt 3800 PSI Pressure Washer

Hello, We have a Candy Diswater that is just arround 2 years old. When it starts it takes water and then you hear the washer going into loop. It tries to do something els but doesn't seem so. If you open the door you can see water inside but no progress or heating. If you also try to change the program it doesn't change as well. Before it got to this point sometimes we used to unplug the power and tunr it off and then ON and then it works. However, now this procedure is not working an


Quite possibly could be the timer and could also be the main control board as well. Sometimes unpluging it will help for short times but if a serious problem persists it will only be a temp fix... ... Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

On my whirlpool ADP962 dishwasher the start light is flashing but nothing is working. I can change the programme type (ie rinse, wash etc) but the programme will not start. I can't select either half load or a time delay. By holding the start button it will start the pump but when this stops it goes back to a flashing start light. The programme progress lights are not lit. What is this telling me and how can I reset it?


... Whirlpool Dishwashers

I have a 2.5 gpm model K2400HH pressure washer that won't sprey with high pressure, it started intermitanly, now won't spray high pressure at all. Last year I removed the valve and cleaned it and put white lithium greese on it and it worked pretty well for a while, but now no high pressure.


I would suggest purchasing a new revised unloader valve, here is the link to purchase one ... Karcher G2650HHR Gas Pressure Washer

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

When I start my Zanussi built in Aquasave zt685 on a normal 65 degree wash it works for a five minutes or so and then stops. When I check, the display has changed to Rinse and Hold. Re-starting it on the quick wash program has the same effect but if I keep re-starting it eventually completes the cycle.


... Zanussi ZT485 Built-in Dishwasher

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

We have just had a Hotpoint FDD912 dishwasher delivered but we can not change the language to English from Italian. The manual says turn on then press the P button and start button together but this does not work. When you power on it says Benventui but quickly goes to Autosuperwash and we you press P and start it just starts the programme.


... Dishwashers

My Kitchenaid ModelKUDI01TJBL0 only leaks at initial start up. Just after the water fills, the first few seconds of the wash cycle. It pours out the front door for a couple seconds than no more for the rest of the wash. It is level, no cracked arms, or loose pumps.Splash guard is in place. The float seems to be working, not too much water in the bottom. I am stumped. Although I do feel that it has something to do with the level of the water being too high, when the arm starts turning, it makes a


Is the unit level or leaning back if leaning back it is morelikey filling too much if level make sure the float moves up/down easy if not clean ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I can't get the igniter to start on north start pressure washer #157224. Fuses ok, indicator light in heat switch does not illuminate. Blower works, fuel dripping out. Cleaned fuel tank and pump and filter too! Tried jumpering past the thermostat didn't help either. Also, swapped pump and heat switches on main panel. No help!


... Pressure Washers

There seems to be an electrical fault in my dishwasher. It is a slimline candy dishwasher purchased only three years ago. Everytime I try to start it all the electricity goes in the downstairs of my house. I changed the fuse twice and it worked for a while only for the same thing to happen again. I also tried to turn off all other electical equipment downstairs to see if this made a difference, but it still didn't work. Would you have any idea what is wrong with it? Thanks. S. Byrne


Hello sue by rne.. \015\012If your fuse blows when you are running the dishwasher alone, I would agree that your dishwasher may have a problem however becuse you stated that it works sometimes..I am more apt to believe that when you run the di ... Dishwashers

Wont start I have a North Star pressure washer that has been in storage for three years.It has the Honda motor GX 160 5.5 I put in new gas changed the oil, air filter,and spark plug.But it wont kick over. Im not sure how to work the levers upon starting it.Theres one for gas, choke,idle,and of course an on switch.Please help


Tip a cap full of fuel in top of the carb to start intitially, check for spark as common fault is on/off switch, If no spark, link the 2 wires on on/off switch together. ... Pressure Washers

Whirlpool dwh b10.yesterday had problem with water not going anywhere,had to bail it out.today cleaned all filters,now can hear pump working but doesnt appear to be taking water in.i press start button for two seconds,re-programme,and it does the above.then start button flashes and there is a continual beep the programme indicator changes from a wash to rinse during this process.any help ? thanks pete.


... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have a indesit idl 40 dishwasher but heater not working changed heater + thermostat still not working


If you have changed the heater then you will find that either the connection from the heater to the control module behind the control panel is poor and may have damaged connections soldered to the module ... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1603 seconds