Having problems with your Dishwashers ?

I have a Kitchenaid dishwasher, model KUDI01FLSS5. When I start the dishwasher, it wills with water, then gives out a low buzzing sound, and that is about all. The water heats up, and eventually drains out, but nothing more. What can be the problem?


Answers :

Hi
\015\012\015\012


\015\012\015\012

If it fills with water as it was filling earlier and the\015\012quantity is fine then the issue is either with the electronic control assembly\015\012or the user interface going bad and should be replaced to solve this. Please\015\012check the water inlet valve and try to clean the water line for any clogs, you\015\012can also test the water inlet valve, if bad replace it. Also before replacing the control the motor should be checked, if you hear the buzz sound from the lower panel then it is the motor if it is coming from the control area then it is the control. Hope this helps...please post back for\015\012further assistance.
\015\012\015\012


\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kitchenaid dishwasher, model KUDI01FLSS5. When I start the dishwasher, it wills with water, then gives out a low buzzing sound, and that is about all. The water heats up, and eventually drains out, but nothing more. What can be the problem?


Hi\015\012\015\012 \015\012\015\012If it fills with water as it was filling earlier and the\015\012quantity is fine then the issue is either with the ... Dishwashers

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Maytag diswasher MDB6600AWW Sprayer arms don't spin. Dishwasher makes all the right noises, except for spraying. Water fills properly and heats up. Water drains properly. Found paper on the back of access panel. Ran Manual Function and Field Service tests, no problems indicated. Disassembled all the pieces inside the bottom of the dishwasher. No obviously damaged parts. Shaft for motor turns freely. It seems like the parts that attach from the impeller to the motor shaft don't


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

My dishwasher will start any program, it drains, fills, empties & beeps continually within a few minutes. The rinse light stays on until the machine is turned off & re-set. Aditonally, the ater heating has been hit & miss for some time! A service guy cleaned the water sensor with hot water fro a ketle + tooth brush, but the problem came back after a couple of weeks. Having removed item he cleaned, it looks fine and appears to switch OK. Not sure if its actually faulty. Is the themperature sensor


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

My dishwasher doesn't seem to fill with water. The heat cycle keeps running and never shuts off. I have discovered that there was some hard water buildup in the drain. I cleaned that out and I still have the same problem. It almost seems like it is not completing a cycle and it won't reset.


Sounds like a bad temperature sensor/thermistor or timer. ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

The lights on the dishwasher are off now after pushing heat dry heat temp the problem is that their is water in the bottom of the dish wassher and it will not drain using the cancel button..


Sorry to read about your problem, I hope this helps you out.You may have a defective pump, on a control card issue...you may also try to reset the circuit breaker, and see if that helps. If not i suggest you contact a service compan ... Dishwashers

I am an electrician, and have been called to repair a faulty Hobart comercial dishwasher. I didn't note the model number, but it is the same shape as the one pictured. The problem is that nothing happens when the lid is closed, like it has a faulty switch or sensor. When I got to site, the dishwasher had been drained, and would not automatically refill. I filled it with a bucket, it heated the water to the correct temp, but still nothing happens when the top is closed, and I have to have it


Hello Pat. Here is the link to the hobart line of kitchen equipment. It has all of their manuals as free downloads. If you have a laptop and internet access you can get the correct manual once you know the model number. Based upon what you said t ... Hobart AM15-5 Dishwasher

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

I have a Viking dishwasher made by Asko. It is less than 6 months old. Today I had a problem with my disposal (water not draining through it and leaking under the sink) and ran the dishwasher, which cleaned/dried the dishes fine. BUT, since the water was not properly draining from the disposal, apparently the dishwasher was not draining properly either. A repairman came to fix the disposal before I knew about the dishwasher issue. Now, the dishwasher won't turn off "draining mode" - button pu


... Viking DFUD042 Built-in Dishwasher

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers

Miele dishwasher makes grinding noise when turned on, there is a light on front next to inlet/drain. So I poured some boiling water into the dishwasher and then left it turned on and could feel the boiling water coming out of the drain hose so I am assuming it is an inlet problem, as it will drain but will not fill or otherwise work.There are a few small cracks in the outer hose of he inlet hose just below the grey box thing, could that be enough to cause the problem? They are only small so I di


... Dishwashers

Dishwashing machine not fully draining (2 inches of water remain). I have an open problem concerning this problem. I have a new pump. dishwashing machine not fully draining (2 inches of water remain) For this machine.


Following a cycle, a small pool of clean water inside the tub is\015\012typical. Excessive water means the pump isn't pumping water out\015\012properly, the drain hose isn't carrying it to the drain pipe, or the\015\012house's drain lines are backed ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

I have a Whirlpool Dishwasher, I had a problem with the garbage disposal, so it was replaced, I hurt myself at the time and my wife had someone install the Garbage Disposal and now you run the dishwasher and no water is brought in to the dishwasher. It does drain, because I put water in and ran that part of the cycle and drained, it does turn on, it does dry but not bring in water is there something basic the guy forgot to do? Any suggestions, thank you.


He turned the hot water faucet under the sink for the dishwasher ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that


... Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

Took these from a previous page, because this is what is happening to our lab Miele Platinum G892/G892 SC. Can you tell me what the problem is and how to fix it? Thanks. intake /drain light is flashing,full water- Guest Feb 26, 2009- I have same problem - open the door and there is water at the bottom of the dishwasher - when I restart program, the water drains out fine. Also, I have great water pressure coming into the dishwasher, filters are clean, etc. I am suspecting it is a circula


If there is verified power at the pump motor - your timer is defective.Thanks For using Fixya!! ... Dishwashers

Bosch dishwasher Over the weekend my drains backed up into the dishwasher. After cleaning the drains I ran the dishwasher 3 times. Under the screen there is still about an inch of water. I never noticed this before because I never removed the screen before. Can you tell me if this is normal or is there a problem with the dishwasher. The water in the little area below the screen is clean.


Its normal. its there to keep moisture around the rubber seals so they dont dry out. ... Dishwashers

I have a Bosch Dishwasher SHU3302UC/14 that will not drain. We initially thought the problem was the disposal because water kept backing up into the sink. We replaced the disposal, removed the dishwasher plug in the disposal, but the dishwasher still does not drain. I would like to check the drain line, but am unable to access it. I removed the kick plate and the screws that secure the dishwasher to the underside of the counter, but the dishwasher will not move. Can you access the drain li


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2257 seconds