Having problems with your Dishwashers ?
Noticed water on floor. Found both heater nuts cracked and letting water by the rubber gasket and tub. Water leaking into the heater power supply wires. Bought new nuts and want to know if this is a constant issue. Nuts are just cheap stampings and it seems likely it will happen again.
Change out your heating element as well. Sounds like you need a better seal. \012
Repair Help & Product Troubleshooting for Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Noticed water on floor. Found both heater nuts cracked and letting water by the rubber gasket and tub. Water leaking into the heater power supply wires. Bought new nuts and want to know if this is a constant issue. Nuts are just cheap stampings and it seems likely it will happen again. Any suggestions Don
Change out your heating element as well. Sounds like you need a better seal. \012\012Thanks ... Dishwashers
AEG 50740 Like Mik, my water isn't getting heated. I have almost got it naked but can't get the front clips to come off so can't get right inside. If it is a water heater issue then I will replace it but I don't know if a new ecu would be practicable. Martin
Some machiens front bottom plastic is a "bump" off type (push sideways clip) Some machiens have electrical elements but some (later models) have inductive heater that fit in line with thewater pipe feeding to the main top washer arm. The electrical c ... AEG 24 in. Favorit 40850 Free-standing Dishwasher
Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?
It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers
My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.
This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher
Spain, very hard water. New dishwasher dif 14 Indesit leaves plates and glasses very calc'd. We use all containers full of products, have additional aids, clean the machine every use, pre-wash; water pressure is high; have tried all programmes. Supplier does not want to know. Before going directly to manufacturers, please advise!
... Indesit DF125 24 in. Built-in Dishwasher
The water won't drain-installed new garbage disposal a few days ago,dont know if this is part of problem but want water to drain-
You must knockout the metal plug in the dishwasher attachment pipe on the disposal. ... KitchenAid 24 in. KUDG25SH Built-in Dishwasher
I want to buy a new GE diswasher but I do not know about water inlet, is it hot water or it could be normal?
Dishwashers are usually connected to the hot water line under your kitchen sink. Although, a dishwasher has a heating element of its own, connecting it to the hot water side minimizes the amount of time the heating element cycles on and reduces the ... Dishwashers
My old Neff dishwasher S4132 is constantly taking in water even when switched off! I can drain it ( every hour!) by putting it to drain cycle but have to turn off the mains supply when leaving it even for a short time. Awaiting a plumber as the tap to isolate the supply has broken but am interested to know if a new aqua stop will solve this problem or could it be something else??
My LG dishwasher -LDF7810st has been a huge problem from the beginning. However I will just focus on the current issue. Previously it was leaking and I kept towels under the dishwasher. Then one night there was a deluge of water all over the place. One guy says the seal is bad then another no its the whole seal around the dishwasher is bad. No one seems to know and I dont want to spend $250 to find out. I remember a previous post that said their was a design flaw with a part of this but cannot f
... LG 24 in. LDF7810 Built-in Dishwasher
Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin
Maytag Dishwasher I would like to know the proper water level after DW fills. Older Whirlpool units a quick guide was when water just covered heater. I have a new D/W and the water supply is difficult to access, there is a kink in the water line slowing the water flow. The D/W fills to bottom of heater, but because the unit is so quiet I can't determine if it is timing out or working properly. I intend to repair water line when counter work is done. Thanks for any help Gary
Newer Maytags should fill close or up to the heater not over. Sounds like your alright for now but I would get that water line fixed. ... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher
Water usage for the Kenmore 2 Draw Dishwasher - 465.1332. I am considering an ''instant'' Hot Water heater, or a Point of use hot Water heater. I am unsure of the size to get since i do not know how much water is used per cycle.
... Kenmore Dishwashers
I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting
All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i
The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers
What could be causing white powdery residue on dishes, glasses & silverware? I have checked the heater element - seems to be hot, using Cascade powder as usual, we have and have had hard water, we do have a new water heater set on 'low' setting - temp of water measured at 113 deg at kit tap. This washer has worked well for 12 years, then white powdery residue. Thanks, Phil
I wont vista ultimate product key ... Kenmore 13869 / 13864 / 13862 Dishwasher
My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem
The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher
New ge modle gld5900n10ww want fill with water cheched high float and water line got power no water
See if the shut off valve is off under the sink it will be on the hot side ... GE Dishwashers
Constant draining my candy cs445 17" is stuck on drain, it just sucks water out and wont stop. Turning the dial to stop does nothing, if i fill it with a sacepan of water it juts empties, and when all the waters gone its just keeps emptying, would a float switch be the problem or possibly a new dial ?
I would check the float.clean it up real good.make sure it moves freely.let me know ... Candy 17 in. CS455 Built-in Dishwasher
Brand new high end electrolux dishwasher perfomring horribly - likely due to hard water issue. Cloudy glass and resident left on dishes. Have the rinse agent set at max and hot water is at 150F...is the only solution a water softener??
Dishwashers have a water softener incorporated but this needs salt to regenerate. have you put salt in? ... Dishwashers
Maytag Quiet Series 300 dishwasher leaves sediment on dishes (primarily glasses) after running the Autoclean cycle. We've taken it apart, cleaned spray arms, filters, float and replaced some seals, but still have problems. We use Cascade detergent and Jet-Dry (what was recommended when we bought the dishwasher). Our water temperature is 120 degrees (maximum setting we can have without having our tankless water heater modified), but this dishwasher problem was an issue with our old tank water hea
The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Maytag 24 in. MDBH950AWS Built-in Dishwasher
I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete
Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher
Zanussi ls9 I have a zanussi ls9 hood-type dishwasher. i'm not sure how to get it going. it runs, but i don't know how to get the soap into the machine, nor if the water heater is on. because the water doesn't seem to hot. PLEASE HELP ME^^!
Write to me if you need the manual.as for the soap the dishwasher uses only liquid professional soap and you must connect it inside the tank . there is also a blue pipe for the rinse aid detergent\015\012let me know if you need anything else ... Zanussi 29 in. LS14 Free-standing Dishwasher
No Water Same issue. All it does is want to drain but drain is empty. No water coming out to clean dishes. Damn!
Water on lower bottom will cause the machine to drain all the time. Leakage or blocked drainpipe can cause this. When you dry out the water on the bottom it will sart as usual. ... Asko D1706 Built-in Dishwasher
Leaking input to the top of the dishwasher. Pollypro pipe comes up the back and into the top centre of the machine.... This is squirting out water when on wash cycle. Have undone large plastic nut on iside.. that has rubber washer on it... but the input pipe does not seem to have a washer between this and the steel body of the machine... this seems to be causing the water to squirt out... please let me know whether the washer has disintergrated or whether I need to use some bedding compound t
\015\012By reading Your problem most probably due to disintegration of washer only. Try with new Washer \015\012\015\0121. First try to adhere some wax or gumming material where washer is distingrated...if it solves u r probl ... Dishwashers
Water not going into the dishwasher, want to know how to change the water pump
The water pump is not bad it is the fill valve it is in the left hand side up front very easy to replace good luck ... Dishwashers