Having problems with your Dishwashers ?

It stops half way through all cycle's with an 'error 3'


Answers :

Hi
\015\012\015\012

Error code really depends on the make and model of your\015\012Dishwasher, it can be a control/motor fault however, please post back with the\015\012model no so that I can tell you the solution. Hope this helps...
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a hotpoint aqaurius dishwasher df23n. When put on wash 4, the timer stops half way through and has to be helped. When the programme then continues through the rinse cycle, it stops half way through. I have tested the water heater and thermostat electrically and they seem ok. Is there anyting else that stops the timer at these positions? The timer knob is free to turn and is not jamming? Steve B


... Hotpoint Dishwashers

I have a Kenwood Slimline Dishwasher KS474s for a year and it has always worked near perfectly. rn However, over the last couple of weeks the dishwasher has not been running the cycles properly (stopping half way through etc, starting the the delay timer half way through cycle), but it always sorted itself after being turned off and starting again. The trouble is now it has got worse.. when I turn it on the panel and lights on the front just flash, the delay sometimes scrolls through on it'


... Kenwood Dishwashers

Frigidaire Dishwasher (GLD2250rdc6) has all lights light up through cycle and stops half way through


... Dishwashers

Ariston dishwasher keeps stopping half way through cycle


... Ariston Technologies Dishwashers

Stops working half way through a cycle and alarm goes off


How many beeps does it make ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Dishwasher keeps stopping half way through cycle have to switcxh off and put back on several times hydrapulse dishlex


... Dishwashers

Stops half way through a wash - Matsui MS452W


... Dishwashers

Half way through a program then stops, leaving water in the bottom of the machine


Check the flood switch first. It will stop the dishwasher but you may hear a moter running. ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

The dishwasher is only one week old. It stops half way to three quarters way througth the cyle and the Start/Resume button flshes. When pushed it starts washing again. If you cancel it doesn't always cancel.


... KitchenAid KUDC03IVWH Builtin Dishwasher

Stopped half way through a wash it stops and beeps for me to open it but when I do it hasnt drained. we checked all the pipes but it wasnt5 blocked so now we've pulled it completely out


This is a typical Anti Flood system activation. This system activates when water leaks onto the floor of the machiene due to a leak fault (pipe/hose clamp/ partly blocked pipe). The machiene automatically switches to pump out mode and stops water inl ... Baumatic 23 in. BDW13 Built-in Dishwasher

Hello My zanussi diva edw1500 stopped working half way through a wash and there is i30 flashing. According to the manual this is some protection against flooding. I thought it was my external drain was blocked and this was stopping the water from being pumped out of the machine. The drains have now been unblocked but when I tried to resume the dishwasher cycle ther same error appears. Please can you advise? Many thanks. Kind regards Jo


... Zanussi Dishwashers

I have an older GE dishwasher, model GSD1200T02. I recently put in the wrong soap, so I had to press the clear/reset button. When I did this, the dishwasher ignored me and seemed to continue through the cycles anyway. When it got half way between "drying" and "off", it stopped, and has been that way for several days now. It will not respond to any button pushes at all now. I cannot even reset it because it does not respond at all when I press the clear/reset button. I have had a load of di


This is only a long shot, try turning the breaker off and on again, may be ???\015\012 Jacques. ... Dishwashers

Beko dishwasher DWD 4310W stopped half way trough a cycle and not drained water


... Dishwashers

Statesman xd400w stops half way through cycle


... Dishwashers

I have an Ariston LSI 61 dishwasher that keeps stopping half way through the wash cycles. Has anyone any ideas what the problem might be and also how to fix it???


... Ariston Technologies Dishwashers

Whirlpool ADG993, door fault: Hi, a few weeks ago soemthing broke on the door to my diswasher and it falls open wide with no stopping half way as usual. That was fine as the machine could still work, but now the door won't close. All seems fine until you get all but closed and then the door raises slightly from the bottom right corner, preventing it from closing. It looks like something may be jammed in there which pushes the door up at the last minute. There's a man coming out on Friday,


... Whirlpool Dishwashers

The dishwasher stop half way .and wil not start up. also all power light is off.


... Kenmore 15892 Built-in Dishwasher

Hi, Our whirlpool adp8540 dishwasher gets about half way through wash and then stops with the light blinking 4 times?


Hi\015\012\015\012Thanks for using FixYa. 4 blinks indicates drainage failure, as it completes\015\012the wash cycle and then blinks 4 times so this also means that the water is\015\012unable to drain. Dishwasher\015 ... Whirlpool Dishwashers

I have a Bosch SMU2046UC/14 dishwasher that makes some noise but will not start the wash cycle. I found that the noise was from the timer motor by removing the front of the door. The timer continues to run and but only advances until half way through the wash cycle where it stops permanently. Is this a problem with the timer or could something else be causing this problem.


HI. The timer motor mechanism regulates the length of time power is to be routed to each component. If the timer motor does not advance properly, it can result in a wide range of problems. Common symptoms will usually include sticking in a cycle(fail ... Bosch 24 in. SMU40 Built-in Dishwasher

When I start the dishwasher, it sounds normal. A few minutes after it starts, it makes a loud, thumping noise that lasts for several minutes. After a while, it stops making noise, but about half way through the cycle, it starts making the loud, thumping noise again. It's loud, annoying, and does not get our dishes clean. We have to wash several dishes by hand AFTER we have run the dishwasher.


I have made the assumption that your d/w is a siemens machine, however if not pls repost with the make and model.\015\012There are a few possibities...check the spray arms are clear by removing any blockages in the holes, check that there ... Dishwashers

Dishwasher programmer stops rotating half way through cycle


... Candy 24 in. CD950 Free-standing Dishwasher

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

Hotpoint aquarius dishwashers keeps stopping half way through wash flashing between the 40 and 60 temp light. How can I fix this please


Control panel is sensitive on this model. Mine did the same and machine would not wash to the programme, stopped half way or would not set at all. Switch off machine and unplug from the mains. Leave for 10 minutes. Plug back in and switch the mac ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

We have a Turbo air dishwasher that is stopping half way through its cycle. the display reads E5. what does that mean and what should I do?


... Dishwashers

Fisher Paykel Double Drawer DD601v2. Half way thru a cycle the alarm went on both drawers even though the top one was not inuse or switched on. The error on both drawers is F1. If we push the power button on both after a few seconds they both start up making a whirring noise and both drawers flashing. We have to unplug the machine to stop the irritation. What is wrong and how can we mere mortals fix it ?


Hi,The F1 error means that the sensor that is located in the pan at the bottom of the machine has sensed water.It does not want either machine to run with a leak so it will shut down the operation of both drawers. ... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0837 seconds