Having problems with your Dishwashers ?

My haier 301 dish washer keeps trying to drain when closed, the cancel button does not respond and when I start a cycle it never shows completed


Answers :

There is a likelihood that the flood switch is tripping which is running the drain pump and shutting off the water inlet. Do you know where the flood switch is located? If you do not see any device under the bottom wash arm then it is at the base of the dishwasher housing under the wash tub.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My haier 301 dish washer keeps trying to drain when closed, the cancel button does not respond and when I start a cycle it never shows completed


There is a likelihood that the flood switch is tripping which is running the drain pump and shutting off the water inlet. Do you know where the flood switch is located? If you do not see any device under the bottom wash arm then it is at the base of ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

I have a Kenmore Ultra 15895 or 15891. It fills with water then doesn't run. It will continue through it's cycles, but stays full of water. If I hit cancel before it completes the cycle, the number 2 shows in the display and nothing happens. If I let it complete the wash cycle, it will sometimes start and wash properly.


HI. The culprit will be the main control sector. This control fault may possibly be corrected by initiating a hard reset. the logic chips are scrambled, and this damage may be correctable by simply unplugging, or shutting off the appropriate circuit ... Dishwashers

Bosch diswasher Turn dishwasher on lights that are showing are heavy duty wash, sanitize and clean lights. Just beeps like a load is completed - tried reset by holding down start button, etc.. Not able to even change cycles - only button that works is the on/off button


... Bosch SHX3AR75UC Ascenta Series 24 In. Stainless Steel Bar Handle Built-In Dishwasher

After 3 years it just started making a loud noise, I am no expert but it sounds like a fan in a motor. I have only heard it today, but I am betting it will still happen next load too. I didn't change any of the settings, have been running the same way forever. When I did hear this noise I started pushing buttons to see if I could get it to stop, no good, no change. The cycle has completed and everything looks ok, waiting on the dishes to dry. Drainage has never been a problem for me either.


I would say this is a build up of lime.try changing your tablets and checking your salt levels.there is no fan .try what i say and see what happens.have you found a glass broken it could be as simple as that but i dont think its serious.adrian,,,, ... GE Nautilus 24" Built-in Dishwasher

Touch panel will not respond to all requests. Wash cycle will start but will not complete through the rinse cycle. The only light that will eliminate is the rinse button.


... Maytag Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

I opened the door before the drying cycle finished. I pressed the cancel button, then I pressed "normal wash" and the "start" button and it didn;t start. Then did "cancel" again . I pressed the "heat" button for five seconds to lock the door so I wouldn;t make the same mistake again. It still won't start. Now the "cancel" button won't work and the start button flashes. What do I do now?


HI. The unit will need to be reset. This is achieved by unplugging the unit for five minutes. If unplugging is not an option, simply,shut down the appropriate circuit breaker for five minutes. This action will, essentially, reset the logic sector. On ... Dishwashers

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

Model #665.1746 The Smart Wash and Normal Wash buttons are blinking, and neither wash cycles begin when the Start button is pressed. The Cancel button drains and sometimes turns off the Normal Wash button from flashing, but it seems no matter what I do the Start button does not start any of the wash cycles.


... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a whirlpool model KuDSO1FL and the clean light blinks and won't start after the cycle has been selected and the start button is pressed. I have tried canceling the cycle but it won't work. The dishwasher was working yesterday and today it drained once we cancelled the cycle and then pressed start but that is all that we could get done. I don't know what the problem is.


Your appliance's clean light blinking will require a service call. It could be several things indicating a problem that are not serviceable by the home owner. You can try turning the power off at the breaker box, then turn it back on and see if this ... Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher does not start, on any cycle selection. the only button that works is the cancel button which tells me the unit has power. this has happened before and a service tech was called and it "magically" started after he pushed the cancel button, not so this time??


Make sure the floor is dry where you are standing. \015\012 \015\012Push the cancel button twice in quick succession to attempt to turn the washer off.\015\012 \015\012Open the door all the way and look over t ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

My Maytag NDB9601 will not start any cycle. You can select the cycle and the display will show the time, but the start and delay buttons, located on the front, not the top with the cycle buttons, will not activate. This leads to the dishwasher not working at all. It worked in the morning, but not in the evening. Dishwasher is 1 year old.


Sounds like a possible door switch problem. \015\012\015\012If you take that area of the door apart, check the ribbon cable for keypad. You can clean the connector with a pencil eraser. ... Dishwashers

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

My daughter accidentally turned on our GE GLDA690 dishwasher. I can't seem to cancel it out without actually starting the cycle. I opened the door before the cycle started but now it is sitting there beeping. The obvious thing is to load it with dishes and run it. But it is just the two of us and we don't really have a load full. Owner's manual is no help. Even turning off the circuit breaker will not stop this infernal beeping. How do I cancel it? Why isn't there a cancel button?


... GE GLDA690MWW / GLDA690MBB Built-in Dishwasher

I have a blinking cancel light on model GU1200xtlt1 and will not start in any cycle. Also if I push another button it flashes rinse button and cancel button. Before this it ran in Sani Clean over and over again and I could not change the cycle. I emptied out a bit of water from the bottom because it did not drain also and the water was not smelling too good.


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1674 seconds