Having problems with your Dishwashers ?

My ignis347 is not washing as well as usual and i note the temp is not nearly as hot as before,it is quite cool after wash


Answers :

Hi
\015\012\015\012


\015\012\015\012

First check the water inlet valve, and try to clean its\015\012inlet screens, if the issue returns then replace the water inlet valve. Hope\015\012this helps...please post back for further assistance.
\015\012\015\012


\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My ignis347 is not washing as well as usual and i note the temp is not nearly as hot as before,it is quite cool after wash


Hi\015\012\015\012 \015\012\015\012First check the water inlet valve, and try to clean its\015\012inlet screens, if the issue returns then replace the water inlet valve. Hope\015\012this helps...please post back for further assis ... Dishwashers

I have a Maytag MDB8951bws and I have noticed that the dishes at the end of the cycle do not feel hot but mildly warm and not completely dry. I also noticed that when I select the ''Sanitize'' option the light that tells you the dishes have completed being sanitized does not come on after the cycles are completely finished (the ''clean'' light does come on). One last note I will throw in is that the high temp wash seems to work quite well as a lot of steam is expelled when the door is opened dur


... Maytag MDB8951BW Dishwasher

Tank temp Our School Dist. has a Hobart dishwasher Model AM 15 T. After filling the unit it reaches a tank temp. of approx. 160 F, but when it is run through a couple cycles the temp. falls below 140 F, the min. wash temp is 150 F. The supply from the hot water tank is approx. 140 F. The rinse cycle reaches well above the 180 F min. Is there anyway to adjust the tank temp. on this model or could you suggest a solution to the problem. Thank-you John Fry


Check to see if your element is scaled up or your element may be damaged ... Hobart AM15T Dishwasher

Hi, my name is GAD. i work at a conference center. our model is quite an old version of the MH65-70 - maybe 1985? How do you adjust the water temp for both the rinse and wash cycles? the gage reads too hot. we have someone here who can service it, knows how to work the electrical, but does not know where to adjust the water temp. Is it a dial? a bolt adjustment? how do we lower the water temp sensor?


Hello Gad\015\012Send me the serial No. of your unit and let me see whether we are talking the same machine. \015\012The one I'm talking about have 3 thermostate with dial to adjust the temperature 1 for Hi temp safty no dial fixed tempe ... Moyer Diebel 28 in. MH65-70 Free-standing Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

GE Dishwasher SSD3900J00ww wash water cool heating element hot on


Crew that installed new cabinets and sink hooked dishwasher to cold water line I switch it works fine now. Thanks Don ... GE Dishwashers

Beko DWD8650 Dishwasher water temp is scolding hot and drying cycle is like a steam bath even on pre wash and no temp


... Beko Dishwashers

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

Kenmore model 665.16509200 Does not clean very well and now dry cycle not working. Wash cycle takes almost 2 hours, and still dishes had gradoo and white detergent on them, even ones that were clean when they went in. The drying coil had plastic melted on it once before, so that could have caused that malfunction. I am not so concerned about that, it is the dirty dishes after 2 hours that is driving me nuts. The short wash cycle leaves EVERYTHING dirty, so I just quite even trying that.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

Our dish wash is not all the time showing several alarms and not performing well. water not hot enough, some times it locks showing a spaner wrench with P1 blinking. it does not rinse very well. It is only 6 months old. We do not have any manual for troubleshooting. Note. All of our kitchem equipment in the platform is hobart. please wating for your assistance.


... Hobart AM15T Dishwasher

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

501ht goes thru wash cycle but cam stops just before rinse cycle clicks in - stays in wash cycle - turned thermostat to booster down in temp -cam then keeps going properly but with no hot water from booster - replaced thermosat still same result - apparently a safety ? no booster water no rinse?


Did you get a solution for this? I am having the same issue. Please email me at [email protected] Thanks -Eric ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

Our dishwasher (a Maytag - MDBH970AW) will not proceed past the intital intake of water. It has done this occasionally in the past, but with repeated attempts to start a wash cycle, it would eventually work and continue to work for some time afterward. However, in the past week, it will not go through a wash cycle. I have ran the water, prior to starting, to ensure that it is intaking very hot water. When it quits, I can push the start button again and it will go through the 2 minute drain c


... Maytag 24 in. MDBH970AW Built-in Dishwasher

Will not quit running on wash cycle for over 8 hours. Water soapy and hot.


Hard to help much without you posting the manufacturer and model number but if your dishwasher is more than a few years old and it has a mechanical dial , I would suspect that dial / timer has failed and needs to be replaced.Please post b ... Dishwashers

What could be causing white powdery residue on dishes, glasses & silverware? I have checked the heater element - seems to be hot, using Cascade powder as usual, we have and have had hard water, we do have a new water heater set on 'low' setting - temp of water measured at 113 deg at kit tap. This washer has worked well for 12 years, then white powdery residue. Thanks, Phil


I wont vista ultimate product key ... Kenmore 13869 / 13864 / 13862 Dishwasher

I have a Maytag dishwasher with stainless inside and 6 months ago it stopped geting dishes clean..We live in the country and so use well water and seem to have a build up of minerals on the inside..but the dishes come out still quite dirty and we have to hand wash..


... Maytag MDB6709AWS Stainless Steel Builtin Dishwasher

The dishes come out with white film on them. During the washing cycle water is not hot, it's only luke warm. I thought it was the heater but the drying cycle works well. Is it all connected to one heater? It is not because of hard water. It worked fine just last motnh. Please help! Thank you!!!


Are you having any issues with your water heater at all. Make sure to run the water at the kitchen sink on the hot side first ti ensure hot water is getting to your dishwasher. Also make sure that the jet dry dispenser has jet dry in it. Hope this h ... LG LDF8812 Stainless Steel Built-in Dishwasher

I have the double drawer dishwasher. It is 3 years old. For about 1 year now one of the programmes - the second one along which is for quite dirty crockery and cutlery (programme is about 99 minutes) - STOPS after about 60 minutes. It bleeps and flashes and the pot wash programme and eco button are on when I open the drawer. Sometimes the programme works right through. No pattern or consistency. Also the dishwasher isn't cleaning terribly well. I've checked the filters as much as I can an


A few things you could do.\015\012\015\012Is this happening with both drawers.\015\012\015\012Take a clean damp cloth and wipe the switches and the inside panel.\015\012\015\012Get a couple of Finish dishwasher cle ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch Diswasher Have Bocsh SMU 2046 UC diswasher. Aprox. 11 years old Has always worked well. Recwntly is not cleaning at 100% as before. Seems to run through cycle as normal and sort of cleans but leaves stains in coffee cups and flatware seems filmy, sometimes a little guk left on dishes, all uncharacteristic of past performance. Tried a thermometer during cycle and water temp is around 151 F during wash, 136 F at rince. and 154 F at dry time. Have checked arms for cloging and are free w


Remove the drain hose and check if you have any residual into it. After 11 years your appliance may need a thourought cleaning.Check also if the pump has enough pressure. ... Dishwashers

Follow-up I've removed the lower arm, I'll spend some time and see whether I can get the pobem sorted out. My wife noticed the the detergent was smeared all over the door and repeated tries didn't get it out. Therefore, the water is not spraying. I can confirm the water is filling on the bottom and draining. The heater is working well. I am thinking there is no pressure to send the water through the tubing to the upper and lower arms. The motor is hot to touch (118 degrees with my temp probe). I


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

Dishes bottom rack are marginally clean. upper rack is never clean anymore. The dish washer cycles through NORMAL and Dries dishes OK. Motor is running, and rinsing can be heard as well as washing cycles. Water temperature is HOT. Different detergents (liquid and powder) were used. Frigidaire model FDbb2040FB1


Just fixed my Frigidaire. The outboard o-ring on the main pump became distorted and stretched. Check your local hardware store as Frigidaire wants $17.50 + shipping. Good luck ... Dishwashers

Poor cleaning Hi, This dishwasher is 1 year old and, until recently, has been cleaning well. Now, the dishes come out spotted and bits of food remain. Wash arms rotate freely. I have tried both liquid and powdered soap. Unit sounds like it is running normally. Water is hot and of normal flow rate. Are there any strainers to clean? Any other suggestions.


The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Model MDB 7600AWQ It is not cleaning dishes well and the bottom water 'slinger' is not rotating. We disassemble the lower assembly and cleaned extensive soap scum and hard water deposits. Lower slinger is still not rotating. Water temp and water level are fine. Pump is getting water to upper slinger and pumping water to drain between wash and rinse and after rinse.


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

When my dishwasher completes its cycle, there is powdered detergent left in the dispenser and the dishes aren't as clean as they use to be. This started happening after I ran a HI TEMP WASH with a SANI RINSE cycle. I'm thinking that either the detergent dispenser door is opening late or the water is not getting hot enough. To check the dispenser door, I left the door open and just poured powder into the dispenser compartment. This did not improve the cleaning.


Hi\015\012 \015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allo ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0783 seconds