Having problems with your Dishwashers ?

Dishwasher programmer fault for model hec12efm


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher programmer fault for model hec12efm


... Dishwashers

I have a bosch dishwasher model number SGS0902GB/05. I use tablets instead of detergent. I put the tablet in the Dispenser and close the lid, noproblem. I then set the programme and shut the door, I usually set the programme to delay start so that it washes dishes in the small hours when all are in bed, however, when I have set the programme and close the door within a minute the dispenser assembly opens and the tablet falls into the dishwasher, I then try and put the tablet back in the dispe


Hello Andrew,\015\012\015\012I'm more than happy to give step-by-step instructions for replacing the detergent dispenser, however it's not cheap (about \302\24350) and it probably doesn't need to be replaced. Some of the smaller component ... Bosch Dishwashers

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

Bosch Dishwasher I have just moved into my flat where there is a Bosch dishwaher installed in the kitchen. I have tried on a number of times to get the dishwasher to start a programme but for some reason it fails to start. It does switch on but I dont know how to operate it. I dont have a manual for it so have not a clue what to press to get the programmes running. I would be grateful if you could help. Bosch Dishwasher logixx Model Number SGS6952GB/13 Installed 2001


Dear Saps,\015\012Go to https://portal.bsh-partner.com/portal(bD1kZSZjPTAwOQ==)/PORTALFRAME.HTM for a pdf download for an Intr ... Dishwashers

Kenmore Elite dishwasher won't finish cycle. I have the same model, problem, symptoms, and fault codes as in thread: http://www.fixya.com/support/t7120066-kenmore_elite Model: 630.16303401 Fault code: H The water at the faucet is hot: 120F I pulled the control board and all the solder joints looked good--there were no signs of burnt solder joints, missing solder, cold solder, etc I measured the current on the grey-black wire at less than 1 (one) amp when the t-shoot says it should


Hello\015\012& Welcome to FixYa\015\012\015\012If\015\012the water inlet valve is fine then it can be a shorted wire or the heating\015\012element itself that is bad and needs replacement. Please get back to me if you\0 ... Dishwashers

We have a Hotpoint DWF31 dishwasher which seems to have a fault in the programmer. On 'Normal (65) and Economy (50)' the minutes to end comes up as '2H' and although I have set it running on both programmes, it doesn't appear to be counting down or performing the normal cycle. On the other programmes it works normally. According to the User instruction book, the programmer is self learning and calculates the minutes to end based on previous use of that programme. Is there any way of resetting th


Hi\015\012\015\012 \015\012\015\012Thanks for using FixYa. Switch off the\015\012dishwasher from the power socket and mains and replace all the cables and\015\012switch it on after five minutes. Yo ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

Hi, I have a Dishlex dishwasher. It's an electronic model, from about 92 I think. The model I thought was B8557WW. It is very hard to see the model number because it's almost washed away. Is the model number maybe located anywhere else on the machine? Could there be a manual or circuit diagram hidden somewhere on (in) the machine? The fault is that it wont start. It reacts to some of the front buttons, and beeps, but not all, and not the start button. Before it stopped working completely, some o


... Dishwashers

Dishwasher does not seem to have power. I have a Kitchen Aid, under counter unit, 9 years old, model KUDS01I. I used it 2 nights ago with no problem. When I push a button, nothing happens, no lights show, etc. It is plugged into the lower half of a duplex socket with disposal plugged into the top. Disposal works, so the problem seems to be with the dishwasher. That also eliminates any issues related to breakers or ground fault indicators, etc. Is there a reset button on the dishwasher? Is there


... KitchenAid Dishwashers

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


Do a "key dance" between normal and heated dry , going bak and forth six times. this will rester the heater fault. That is the clean light flashing code. Now you have to find the cause. Most likely is that there were suds in the last cycle or the do ... Dishwashers

Whirlpool dishwasher I have a whirlpool dishwasher model # 665.16519202, and the clean light flashes 7 times then pauses. I was having a problem with the machine working properly right befor the fault code came up and froze it. Can you give me any guidance as to the problem of this washer? Thanks in advance.


If the dishwasher doesn't sense a water temperature increase, it will stop working and lock the functions (clean light flashes 7 times, all buttons are non responsive).To resolve this you will have to reset the console. Do this by closing ... Whirlpool GU2400XTP Built-in Dishwasher

Smeg df612 dishwasher problem, lights up as a e2 fault ,i have tried draining the dishwasher but still the same problem . the salt container is full of water is this normal?. and how do i reset the machine . ive tried pressing the programme button 4 times but it just shifts through the different cycles . can you help please/.


... Smeg Dishwashers

I have a 4yr old Smeg freestanding dishwasher. Model is DF612SDX. The problem is that a wash cycle will start but about 15 mins in it stops and 2 of the programme option lights (on the left hand side of the programme options), start flashing. If you open the machine the soap dispenser has failed to open. This problem has been a bit of a slow deterioration as we've had a number of washed that have managed to finish and then noticed that although the dispenser has opened it must have been to


... Smeg 24 in. DWF612SS Free-standing Dishwasher

I have a Hotpoint LFT04 dishwasher which has now developed a fault. It runs and then stops mid cycle with flashing 2 and 4 lights as well as the power on/off button. Could anyone assist with the diagnosis as the manual does not help for this combination. From reading other similar models looks like heater or wiring fault?


... Hotpoint Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Kleenmaid dishwasher model DW34 X fault D14 Pump filiing fault


The water inlet valves may not be getting water to the pump or the pump may not be operating.Remove panels to access water valve and pump. Listen to see if valves open. You can test power to the valves to see if valves are faulty or if they are ... Dishwashers

Hi, I have an Electrolux ESL4115 dishwasher. There is power to the machine. There are no fault lights showing and the programme selection won't move from the 65 degree programme. When I close the door to start it nothing happens. Any ideas what the problem is please? Many thanks


... Dishwashers

My LG dishwasher, model LD-12AW2 runs for 10 - 15 mintues and then goes into a H and flashing 'E' fault. This fault isn't listed in the manual.


Happy to be of some help. Please keep this list around so you can take notes if the problem comes back.Good Luck! ... LG Dishwashers

CDA dishwasher (model number CW496) , stops working at the rinse cycle, and does not empty, filter is ok, tried re-setting the programme but unless there is no water being held the programme won't work


My dishwasher starts off with good intentions then a couple of minutes later it starts beeping non stop.I open the door to find it has turned on to the rinse cycle and will not do its job.I continue to start it again and then it repeats the problem a ... Dishwashers

My Lg Dishwasher , model 12aw2 , has an error message OE shortly after start up , dishwasher is over 6 years old , is this a simple fault to repair? or not worth it ?


The LG error code OE simply means "the pump is blocked". Presumably the water isn't being emptied properly. As with all error codes it is possible that there is a cause other than the exact description in the error code explanation but basically this ... LG 24 in. LD-12BW5 Free-standing Dishwasher

F&P dishwasher; Model DW 691ED WH; Fault - F4 on display. What is this fault?


Hi there,\012It means your filter is dirty. Remove metal plate at bottom & scrub with a toothbrush. Clean arms as well.Clean all around the door & pull out the lift out filter, scrub clean with a toothbrush.good luck ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Kleenmaid dishwasher model no. dw34x shows heating fault but there is no heating fault wat should i do??


... Dishwashers

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

FIX F1 FAULT CODE ON FISHER PAYKEL DISHWASHER MODEL DD603


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have an Indesit Dishwasher model the programmer sticks


One of the main reasons for the timer sticking, is the heating element is not comming on. Check if it is faulty or if the over temp. th/stat has activated.(Basically,check if water does heat at any time.. if not, there is the problem). ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1395 seconds