Having problems with your Dishwashers ?

Can not clear F2 on the display, programme will not runc


Answers :

Hello,

This means that the Dishwashers has detected a condition it needs to check.\012Press "Cancel" to clear the display and to stop the beeping sound, then\012try turning the Dishwashers off and on again.\012If you still see the "F," turn off the power to your Dishwashers and wait five\012minutes before turning it on again. If you hear the beep or see the "F"\012when you try to washing again, please call your authorized\012provider for service.

Hope this help?.

thanks for visit.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can not clear F2 on the display, programme will not runc


Hello,This means that the Dishwashers has detected a condition it needs to check.\012Press "Cancel" to clear the display and to stop the beeping sound, then\012try turning the Dishwashers off and on again.\012If you still see the "F," tur ... Dishwashers

We have just purchased an IQ100 SE26N250G Dishwasher and are having problems in setting the washing programme. We have followed the instructions in the leaflet but the dishwasher will on wash on 40 degrees and cannot be cleared or changed to any other programme. Also, the information in the instruction manual that accompanied the dishwasher is not at all clear and is rather confusing as it shows that to clear an existing programme you simultaneously press and hold the 2nd and 4th buttons out o


... Siemens Dishwashers

Dishlex global 450 _ how do i fix fill level time fault? displaying oF? Hi There, I have the above dishwasher and saw your advice on fixing fill levels - my display is showing the oF message and the pump to drain remains on whilst mains is connected. turning off mains does not clear message. holding eco button down does not clear message? is there anything else i should do in terms of removing parts to assist the process? I have cleaned out all of the drainage bowl and all is clear. i would pref


... Dishwashers

Whirlpool ADP5966 developed a leak at small rubber connection from circulation pump. Leak repaired, machine reconnected, programme selected, some sound for about 20 secs then shutdown. Display showed F6 once then nothing. L.E.D.programme indicator glows, display remains blank, start light flashing. Help please


... Whirlpool Dishwashers

Set dishwasher to start - sounds as if it starts but then 5 mins later beeps. When door is opened nothing has happened and instead of the i.e. P4 programme displayed E1 is displayed? Can you help on what might be wrong?


Possible that there are no outputs from the program controller unit and so you will need to check with a multimeter the voltage to the inlet valve/motor while the washer starts. If there is no supply then the controller is faulty , if no ... Smeg DWI614 Built-in Dishwasher

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring The solution I tried didn't clear the error code on the panel. Is there a reset or do I need to replace the aqua sensor or ? The machine still won't start and displays a #1 on display. There is no water in the whi


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

There is a 'Cr' message on the display panel, and none of the buttons respond while this message is displayed. What does this mean, and how can it be cleared so that the dishwasher can be operated normally?


Mine is doing the same thing right now. It started beeping again this morning after I wiped off the touch pad. I shut the power off to it at the box and when I turned it back on to try to make it work it just showed the Cr on the display. ... LG LDF9810ST Built-in Dishwasher

AL3 Some way into the dishwashing programme the display indicates a programme identified as AL3. Does anyone know what the problem is? All the manual gives is a suggested solution - contacting a service agent.


... AEG 18 in. Favorit 64800 Free-standing Dishwasher

I have an ADG 977/3 model approx 10 years old, never given trouble but now seems stuck in a rinse mode, i have pressed the start button for 5 secs and cleared it reset it for a wash programme but when i close the door the programme returns to the rinse position and keeps beeping every 2 or 3 secs


... Whirlpool ADG332 Built-in Dishwasher

Candy dishwasher (CDI 1012/2-80) On/off button is stuck in the depressed position. No lights displayed in Programme Indicator Lights on control panel. Programme key not responding. No apparent sign of life. Fuse has been checked and changed on the wall.


... Candy Dishwashers

Creda 47918 - quick wash works OK all 3 other programmes display 99 in the LED for time programme takes. Seems to start filling etc but doesnt go throught cycle. Any ideas


... Dishwashers

Bosch cloassixx model--programme gets stuck on drain--have tipped back to clear base water and this gets water coming in and programme progresses--then stops again


... Bosch 24 in. SGS4072 Free-standing Dishwasher

My machine displays "Start the cleaning programme"


... Miele CVA4066SS | 24" Built-In Whole Bean Coffee System - Plumbed

Beko dw 600 dishwasher, all programme lights stay on and it wont run or clear


I had this problem and followed the advice from Gallagher to no avail.I sorted it as follows andd bear to mind I have never seen inside a dishwasher. I found the float valve and removed the connection to open circuit the switch, still the sam ... Beko Dishwashers

My bosch sgs5312 dishwasher seemed to complete its washing cycle (Zero with a dot on the display), but the pump still seemed to work for hours. Tried to re-set to no avail. Cleared filters and the pu


... Bosch Dishwashers

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

Machine not starting ...Programme Progress Display light flashing


This normaly indicates an error code. Could be the anti flood device activated due to water leaks etc. The anti flood device (polystireene float and micro switch at base of machiene) puts the washer on pump out mode and shuts off the inlet water. Dry ... Dishwashers

LFO 73 IT Fagor dishwasher - will not turn on, display will not light up properly to register programme. Any ideas?


... Fagor LFA-073 IT Dishwasher

I have a Siemens SE25A836GB/35 dishwasher. the program is running and it sounds as if the pump is running all the time. I have tried resetting the program but to no avail. I have checked the filter CLEAR and the water supply is okay. The display in the front which state time to run on the program is blank can you solve the problem?


... Siemens 24 in. SE25A836GB Hi-Line Free-standing Dishwasher

On my Bosch dishwasher Excell"check water" LIGHT COMES ON E 15 fault displayed I have this problem, and can't re-set the programme, even if I switch at the mains, still appears, what should I do? Klaudia


I solved the problem, by tipping the dishwasher back about 45degrees, I think this re-adjusted the flood sensor, and it is now working fine. Thank you. ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

Whirlpool adp 4735 time display shows wrong washing time and does not match the timing of programme selection


... Dishwashers

I have a Diplomat ADP 8520 dishwasher (possibly SMEG manufacture) which will not stop trying to empty. There are 4 leds lit reading left to right and it beeps. I have read on some forums about pressing the programme button 4 times or holding it down for ten seconds to clear the fault but neither of these solutions work. I thought maybe that the drain was blocked but I put the pipe directly into the sink and it empties ok, problem is, it does not stop.


Fault is probably water in the bottom tray operating the anti-flood device. take bottom front panel off and mop out the water and it will work. if fault reoccurs then you have a leak ... Dishwashers

Neff Dishwasher We select a hot wash programme, and when its finished the soap is in the bottom of the machine with some of the items still dirty, others just feel unwashed, i have checked the salt and rinse aid, im using finish as reccommended, the filters are clear, any ideas please


It sound like a detergent cup issue (not opened in time).\015\012The detergent cup itself can become clogged with old dried detergent that prevents it from opening. Sometimes just cleaning the cup takes care of the problem. \015\012Let me know with y ... Neff 24 in. S5543X2 Built-in Dishwasher

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0310 seconds