Having problems with your Dishwashers ?

Hello I have a Bosch dishwasher SHU9905UC and went to clean the spray arms etc and ran the machine without the filter screens in the bottom. **** went everywhere, food, soap scum etc and it first stopped draining and filling. Cleared the drain flap and now works on drainng and filling. But now the wash pump is not running. I figure **** is somewhere in the wash pump or blocking a micro switch etc. I can turn the impellor with my finger. Is there a micro switch in the pressure chamber that is a


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hello I have a Bosch dishwasher SHU9905UC and went to clean the spray arms etc and ran the machine without the filter screens in the bottom. **** went everywhere, food, soap scum etc and it first stopped draining and filling. Cleared the drain flap and now works on drainng and filling. But now the wash pump is not running. I figure **** is somewhere in the wash pump or blocking a micro switch etc. I can turn the impellor with my finger. Is there a micro switch in the pressure chamber that is a


... Dishwashers

Model F180 have just replace the rinse boost pump, but it doesnt want to fill, filled by hand washes etc but eventually runs out of water the fill solenoid is fine


Is the water level float stuck in the up position? it controls a switch which controls the fill solenoid. ... Dishwashers

I have an indesit dishwasher dif16, suddenly it stopped going through its washing cycle, at present it will fill with water and the powder door will open it makes a noise as if a motor of some sort is running and thats it, it will not wash, if i switch it off the appliance the water will pump out, please can you advise what i need to fix this


... Indesit 24 in. D61 Free-standing Dishwasher

Asko 1375 unit will not wash drains and fills ok  motor at back of unit runs well. Suspect impeller   Does motor have to come off for impeller replacement?? My 1375 is leaking a bit, looks like the seal which was mentioned in the impeller repair case,may be the problem? The other problem I noted was a clogged screen at the bottom of the dishwasher which is on the suction side of the pump, the screen had calcium buildup etc. I cleaned it off with vinigar and reran the dishwasher seemed ot fix th


Do you mean to say that the washer does not go into the wash cycle at all, or washes poorly?An answer to both can be found HERE.This article ... Asko 1375 Dishwasher

FDW60 dishwasher Hi My dishwasher is about 15 months old and the problem I have is that it seems to stay on pump and the Ecco45 light is flashing.  A repair company looked at the machine and said that the motor looked like it was leaking and water was getting in the bottom setting off the micro-switch.  He contacted Hotpoint who fitted a new motor today at a cost of £89.85.  Went to use dishwasher tonight and we still have the same problem.  The dishwasher started the washing programme for about


I've just (as of 10 minutes ago) had the same problem. I followed the advice given elsewhere in this forum and removed the bottom cover - water running out so needed a big towel to mop it up. I stood the machine upright and restarted it - no problem! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Frigidaire dishwasher Water does not go through arms, bottom or top, at all (does not wash). You can hear motor running. Pump works fine; discharges water as normal and fills to proper level. Problem just started with no warning; no strange noises etc.


CHECK WATER INLET SOLENOID OR TIMER ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a Bosch SHE56C05UC/40. The unit fills and drains ok but the circulation pump will not operate. I run the diagnosis according to another of you posts and came with an error code E1 which is a heating code. Why would this prevent the pump from running? Your diagram show a flow switch in the heating circuit which won't close unless the pump runs. A diagram of the pump circuit would helllllp.


Follow the instruction code in your ins.manual if you do not have go for free download : www. fitness.manualsonline.com or www.ret ... Bosch SHE56C02UC / SHE56C06UC Dishwasher

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

GLD4050 DW won't pump out at any time during wash cycle. Removed lower arm, screen, etc. and washed and cleaned out everything. Removed drain hose and cleaned it out. Reinstalled and ran again. At no time during he cycle does the water pump out. HOWEVER, if I put my hand on the drain pump I can feel and hear the pump running as usual at the right times in the cycle. What else could be preventing the pump out? Thanks!


You could have a plugged pump itself or broken propellers as long as drain and screen are clean which looks like you already took care of that. ... Frigidaire GLD4050RHS Builtin Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

My dishwasher siemens se25a266gb purchased in 2003 will fill with water go through a wash cycle but does not pump out the water i have cleaned out the filters, checked the exit hose and all seems ok the only way to get the water out is bale out by hand. after this it will run through a wash cycle then stop and not pump out. how would i get to the pump and check it? any help appreicated regards Alan


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Kitchenaid dishwasher model KUDM01TJB0 Fills with water, heats water but pump dosent run in wash (dosent spray water) Drains water. Every thin appears to work but the pump in the wash mode. I checked the control board and it has no visable issue.


... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1180 seconds