Having problems with your Dishwashers ?
White and pasty, thinly covering all dishes, utensils. Appeared out of nowhere after using this dishwasher for 6 months without a problem.
I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new spray arms online and installed\012them in minutes...now the thing works like new... However I have also\012found that if the heating element goes bad then that also can mess\012things up bad... So I would buy new spray arms, and also check out\012the heating element to make sure it is working... Here is a tip that\012will help you with the online buying...
Dishwasher\012Spray\012Arms not Spinning
How\012to Buy Appliance\012Parts Online
A\012bad heating element causes many problems in\012dishwashers...
Dishwasher Problems The Heating\012Element not Working
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
White and pasty, thinly covering all dishes, utensils. Appeared out of nowhere after using this dishwasher for 6 months without a problem.
Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Dishwashers
I have had my Bosch dishwasher for about 2 years. Over the last 8 months or so my dishes come out with a white film over them. I do have hard water, but have had it for over 20 years without a problem like this. The white film is all over dishes, silverware and the inside of the stainless steel washer. I use a rinse agent and have tried many detergents. I have used vinegar to clean the inside. What can this be?
... Bosch SHE45M06UC Built-in Dishwasher
Hi I have a Zanussi ZDF501 dishwasher that stopped heating up intermittently. It got worse and I fitted a new heater and all was ok for a few months. Then the intermittent failure started again. Note that I tested the old heater and it is actually OK without a short circuit so I don't think it was the problem adn can be re-used. Could it be the thermostat or heat sensor? I am concerned it might be the PCB since the failure was intermittent. Thanks Dave
In my case, although the solder joints on the relay looked poor, improving them didn't help. I had to replace the relay. Fortunately, Maplin stock a compatible one, JM67X for 1.99. See ... Zanussi Dishwashers
I recently bought a different type of dishwashing detergent for my Frigidare dishwasher and my dishes look as if they have not been rinsed. They cycled all the way through the drying cycle so the detergent dried on and was difficult to remove. I would like some advice on whether this sounds like a detergent problem or mechanical problem before I try another load. This washer is not new. It was in the house I bought and I've only been using it for about 2 months. (I usually use Casade Liquid and
The best way to use your dishwasher is the way it was designed.\015\012if your unit has a compartment for jet dry or rinse agent then you should add and fill that compartment with rinse aid. try not to buy soap with any extra like soap with jet ... Dishwashers
FDW60 dishwasher Hi My dishwasher is about 15 months old and the problem I have is that it seems to stay on pump and the Ecco45 light is flashing. A repair company looked at the machine and said that the motor looked like it was leaking and water was getting in the bottom setting off the micro-switch. He contacted Hotpoint who fitted a new motor today at a cost of £89.85. Went to use dishwasher tonight and we still have the same problem. The dishwasher started the washing programme for about
I've just (as of 10 minutes ago) had the same problem. I followed the advice given elsewhere in this forum and removed the bottom cover - water running out so needed a big towel to mop it up. I stood the machine upright and restarted it - no problem! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?
Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers
Maytag Quiet Series 300 dishwasher leaves sediment on dishes (primarily glasses) after running the Autoclean cycle. We've taken it apart, cleaned spray arms, filters, float and replaced some seals, but still have problems. We use Cascade detergent and Jet-Dry (what was recommended when we bought the dishwasher). Our water temperature is 120 degrees (maximum setting we can have without having our tankless water heater modified), but this dishwasher problem was an issue with our old tank water hea
The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Maytag 24 in. MDBH950AWS Built-in Dishwasher
We have a model # 1385 Asko dishwasher. For the last few months we have found a film over all our dishes and pans washed in the dishwasher. We have found vinegar removes the film, but the need to constantly wash the already-washed dishes in vinegar to be defeating the purpose of using the dishwasher! We have used Cascade Complete for years, but we have tried different brands now, but nothing solves the problem. Can you please help us??????? Nancy Vocci
Hi \015\012Try running the hot water through the sink faucet, right before you start the dishwasher, so that hot water will instantly be there to run in the dishwasher, instead of it starting cold and having to warm up wh ... Asko Dishwashers
Candy csd-68-80 all four lights on front panel lit, started flashing within few seconds of switching dishwasher on, no previous problems,dishwasher not overfilled, checked manual which said too much inlet water unsure what this means or how to check it. do all usual cleaning,salt,arms etc. had dishwasher about 14 months and use it every day never had any problem before
... Candy Dishwashers
My mother has cancer so needs me to research her problem with her dishwasher. My mother's sink drain water is emptying into the dishwasher. It has to be manually removed since she does not cook much and therefore no longer uses the dishwasher as much as she used to. Is there anything I can do without calling a repair man or plumber? And if I must call a repair man, which should I call, a Maytag repair man or a plumber?
Problems associated with water from the kitchen sink back filling into the dishwasher are caused by the drain line on the dishwasher not having a high end loop. In simple terms, the dishwasher line is too low and is providing a path for the water to ... Maytag Dishwashers
I have a Delonghi DW67S dishwasher which I have been using for about 2 months now. It has been 3 washes now that the dispenser hasn't opened while washing leaving the detergent still in the dispenser. I have replaced the detergent with a new one from a different batch but the same problem. I have also chosen a different washing cycle to see if it was that particular cycle I was using but still the same problem.
Dear Sir/Madam,I have owned a Beko DW450 slimline dishwasher for 13 months and used it only twice, i wanted to use it last night but when i switched it on the drain pump activated and would not switch off. I powered down the dishwasher to see if that would reset it but unfortunately when i started it again it did the same thing - drain pump activated but would not stop running, it is impossible at the moment to carry out a wash programme. Does anyone have any idea on this problem. Thanks, Patric
... Bosch SHU5315UC Dishwasher
Extremely heavy limescale residue on all items after dishwasher has finished. water temp in house has been turned down. Had water tested by city water company and results were clear. 12 months ago maytag replaced heater element under recall, but dishwasher always seems too hot. Neighbours do not have this problem. Any advice would be most welcome.we only use quality powder and rinse aid. Have cleaned dishwasher numerous occasions. model MDB4651AWS1 SERIAL # NW5015848
Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... Maytag 24 in. MDB4651AWS Stainless Steel Built-in Dishwasher
Whirlpool dishwasher ADP 4502 Water fills and stops repeatedly then its drains immediately without washing and then stops Cant use the dishwasher @ all. resetting it doesn't help I am 7 months pregnant, insulin dependent and really my dishwasher
Hello, ryklien\012 \012 I was trying to help\012 you out here. I was going back to some customers that asked questions \012in the past and it appeared that no one answered them, so I thought I \012would take som ... Whirlpool 24 in. ADP5962 Free-standing Dishwasher
KUDS30 leaking my kitchenaid dishwasher (about 1 1/2 years old) had a leak bottom left side and had gasket replaced. It worked well for approx another 6-9 months without any leaks and now the same problem is back. The dishwasher isn't overloaded. A repair person came last week and ran the dishwasher empty and it didn't leak when she was here. The 2 loads after continue to leak approx 2 cups of water each cycle.
... KitchenAid 24 in. KUDS25 Built-in Dishwasher
Dishwasher (Model # SHU6806UC), unit is about 8 years old, very light use, less than once a month, and no previous problems. Turned on unit and after about 10 minutes, I found water on floor coming from dishwasher. Turned unit off and turned off water shut-off valve. Removed dishwasher from cabinet. Found mice had chewed a hole in water discharge hose under unit, inspected all hoses, and found another hole chewed in the 13" flex hose in the front of the unit. Also found the float chewed to alm
Hi,\015\012 Check the valve is open where the supply gets its water from the sink supply.There is a garden hose type swivel adapter after the valve, Close the valve tightly and then unscrew that hose coupling and see if the hose is full of w ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher
We are on the mainland but our dishwasher is on the island of Maui. We are told that the main control board is out. The dishwasher is only about 4 years old and is used only about 4 months out of the year. Is this a commmon problem with Bosch dishwashers? Is there only one "Main" control board? If so, do you know what the part number is? thank you.
... Bosch Evolution 800 SHE58C02UC 24 in. Built-in Dishwasher
My dishwasher has no connection. The entire "board" is without lights. I cannot start the machine. My biggest problem is getting support from local service! I have not talked to anyone who will help! The service depart. does not return my phone calls! Dishwasher was purchased two years ago this month, Model number:MDBH945AWW
... Maytag Dishwashers
Dishwasher is 16 months old. Recently, it won't get tea stains from spoons or cups and there is a white film on plastics. I have run unit once with vinegar. I tried using less detergent and no change (Cascade Complete). (Neighbors using same detergnet on different machine with no problems so it's not the water.) I always select High water temp and air dry on normanl wash. My hunch is that the motor is going bad and therefore it is not pushing the water with enough force.
Hello, there are a few thinks to check on the dishwasher. Circulation, drainage - no backflow back into tub, and water temp. If all three are good, then you have hard water. \015\0121. circulation - These MDB models are very good with water circul ... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher
In the last month I have noticed that my dishes aren't getting clean. My dishwasher is less than a year old and has done a great job so far. I tried adjusting the amount of rinse aid and the amount of soap but nothing works. the dishes come out "clean" without food residue on them, but they are so cloudy that I don't want to use them. I will go back to handwashing and sell the dishwasher is this is the way it is going to be cleaning. (The repair guy said nothing is wrong with it.) It is mod
First I would run the hot water until hot. Then start the dishwasher on the longest setting with the dispenser door closed( no detergent). Then after about 10-15 minutes open the door and check to see if the dispenser door opened, it should have. The ... LG Dishwashers
My Maytag dishwasher is 9 years old-- Model number MDB7100AWW, serial number 27754072ZQ It has worked fine until about a month ago, when I began noticing a kind of "scum" on the silverware and some of the dishes after completing a wash cycle. The top rack will squeak and have some resistance when pulled out, whereas before it always came out smoothly. I have always used powdered Cascade. I've tried using less, thinking I might be putting too much in. Then I got a rinse agent. These thin
We had the same problrms, and then the machine wouldn't even clean anything, we took apart the lower spinner and cleaned the plastic filters and now it works like new ... Maytag Dishwashers
About a month ago, our dishwasher stopped working properly. It runs fine and the soap is being used, but the dishes are not being cleaned and especially on the top rack. I opened the dishwasher this morning while it was running and I noticed that the coil on the bottom was red (maybe heating water) but only about 1/16th of it. Could this be the problem?
Hi\015\012In a dishwasher you can see the water trickle upward to the upper nozzle in dishwasher...but if it does not have enough pressure,it will not function properly.tap the delivery tube that feeds this nozzle and you will see the water pre ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher
INDESIT IDL505 DISHWASHER(2nd hand working fine for 3 months) started to notice some light/slight streaking, misting especially glasses(annoying but not to much of a problem) then about two weeks later heavy streaking,glasses totally misted completely did have a brief problem with water inlet solenoid but checked it and its working properly (only malfunctioned once) i refilled the salt container and put on a simple wash and found that it used about half the salt in the container,changed the hard
Maybe the machine got a leaked inside.. ... Dishwashers
Blanco BFDW6 dishwasher drains and sounds like it is going to start but stops after 2-3 seconds. Yesterday it was playing up and made a fairly small puddle on the floor. Electrics seem to have been a problem from early on as after a few months it would let me open it during the beginning of the cycle to add items without needing to restart program. I am not sure if problem is electric (may need a reset?) or due to anti-flood feature.
... Frigidaire 24 in. FDB126RB Built-in Dishwasher
She6af02uc bosch dishwasher Light is flashing, but won't start. I used it earlier today and it worked fine. Like I said the time light is flashing, but I cannot change settings nor will it start. Turned it on and off a few times to no avail. Did I lock it or something? How does one unlock it? Hardly used and only a couple of months old... Never had this problem before!
... Bosch Dishwashers