Having problems with your Dishwashers ?

I have a GE dishwasher Model #GSD2030F03WW. It runs through the whole cycle but the water does not go into the unit. I checked the lines and they are all hooked up correctly.


Answers :

Fsd66fSorry to read about your problem.
Their is a 60% chance that your cold water inlet valve is stuck. 30% that you water leval sensor is defective.
I suggest you contact a local service company to repair your problem, this should be 1 hour or less service call.

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck.

If you are in the Denver area, I can help you out
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a GE dishwasher Model #GSD2030F03WW. It runs through the whole cycle but the water does not go into the unit. I checked the lines and they are all hooked up correctly.


Fsd66fSorry to read about your problem.Their is a 60% chance that your cold water inlet valve is stuck. 30% that you water leval sensor is defective.I suggest you contact a local service company to repair your problem, this should be 1 ho ... Dishwashers

Dish Washer, Electrolux Home Products, Model FDB2510LCC0, Serial NO: 7H34962223 Machine does not drain or add water. The machine has been worked for a couple of years. I checked the following: 1. Overfill Protector not stuck 2. Motor turns on and the machine cycles correctly 3. Since the machine has been running correctly the unit is hooked up correctly: hoses, garbage disposal, knockout plug. Again everything has worked and the motor does cycle and the machine will perform the different cycles


... Electrolux 23 in. ESI602 Free-standing Dishwasher

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Have GE Dishwasher model GLD6700N20WW,unit has stopped draining! Took apart and pump was running when check, but no water coming out. Checked drain line and pulled apart pump housing, all clear. Thought maybe pump has a silinoid built inside of it and was stuck shut, so bought new pump and same thing, no water will go thru! Please help me? Is it control module, or turbitity sensor possibly?


... GE Profile PDW8600J Built-in Dishwasher

Purchased ge dishwasher model ghda674n00bg and discovered after installation that I removed the rubber check valve from the discharge line in error. Is it mandatory that this check valve be installed? Naturally I would prefer not to remove and reinstall unit. Thanks for your help Regards, John


... GE Dishwashers

I have a Frigidaire dishwasher. Model FDB520RHS0, Serial TH92539147. The drum fills with water but will not drain. I purchased the unit about 2 years ago. It has been used sparingly and mostly on light wash. I removed the basket and could find nothing blocking the drain. Is there a fix? Can I replace the drain pump? The unit is making a noise as if it is trying to drain but nothing is happening. I have checked the drain line for clogs and it is clear and the terminal end is conn


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

WE JUST BOUGHT A NEW DISHWASHER DU1345XTVB HOOKED EVERYTHING UP CORRECTLY AND RAN A QUICK CYCLE THRU IT AND WHEN IT WAS DONE THERE WAS STILL WATER IN THE BOTTOM. THIS WAS TO REPLACE THE OLD DISHWASHER SO IT WAS ALREADY HOOKED UP THRU THE GARBAGE DISPOSAL. WE CHECKED THE HOSES NO KINKS...VERY FRUSTRATED! HELP!! TRISH W.


Make sure the garbage disposal is working, if it is not then it will not allowthe dishwasher to drain. Also make sure there is not blockage in the intake port on the disposal where the hose connects itself. If you installed a new disposa ... Whirlpool Dishwashers

The Intake/ Drain light is on. It appears that the machine is not draining and that possibly the pump is not working properly. The drain line appears to be clear though I haven't pulled out the unit to check the drain line at the machine. Any suggestions?


... Miele Touchtronic G832SC Built-in Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

I removed an old dishwasher and replaced it with this GE 24" Profile GSD533ODO1WW unit. It seems to run through the cycles like it should but it doesn't seem to run any water for some reason. I hooked up a new water line to it and turned it on. There where no leaks that I could see. Is there any installation manual that you could send me to make sure that I didn't miss anything or is there anything that you can tell me that I should look for? Thanks, Jesse


... Dishwashers

Our dishwasher doesnt seem to be cleaaning the dishes properly. After the cycle soap residue remains on the door and bottom of the unit and the dishes are not getting clean. I have checked the supply line and discharge for blokage but both are clear. what should I be looking for?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Bosch dishwasher not letting water in to the unit. I have checked the water inlet and there is water coming through. However there is a electrical smell to the uniot and seems not to be going through its cycle correctly


You need to replace the water inlet solenoid valves as a unit,you can normally do this from outside the unit,some you may need to remove rear cover to replace it ... Dishwashers

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Hi I have a whirlpool diswasher which is about 7 uears old which has blown the fuse (and the mains trip) half way through a cycle. Replaceing the fuse has resulted not resulted in the restoring of power to the unit. Is there anything simple I could check (in line fuses etc.)? Cheers


Some whirlpool models do have a thermal fuse in the consloe mounted to the main control board housing, might looke to see if it has one and if it is good ... Dishwashers

I have model 1380 and it has worked great. We recently moved and now want to use it, but it has been unused for over 3 years. Got it all hooked up and greased the o-rings and plugged it in and it will not start. I can't reset the GFCI as it does not seem to move or do anything. Any suggestions on what my problem may be and how do I correct it, short of buying another unit? Joe


... Campbell Hausfeld 1,350 Psi Electric Pressure Washer With Auto Detail Kit #PW1350

I have a GE Triton Dishwasher Model #GSD5320D02BB, Serial #FA792902B in muy home which drains into a garbage disposal unit. The water doesn't drain out of the dishwasher after a wash cycle is done. I have checked the drainage line, it is not blocked. My opinion is the drainage pump is not working. Can you adise on this? Plaeas reply at [email protected]


Two things, one of which you probably already have done:(1) if the drain goes first to a vent or siphon breaker before entering teh sewer, make sure the siphon breaker is clear of debris - easy to do, it is usually on top of the sink(2) t ... GE Dishwashers

Ice maker cannot eject cubes. I took off the front cover and found several contact points for checking the motor, water valve, thermostat, mold heater. There is also a line voltage and neutral contact. Are these contacts live only during certain parts of the cycle? I suspect the heater isnt working to loosen the cubes so they cant be ejected. The motor sounds lilke its running but the ejector is not moving nor is the Gear on the front of the unit. Can someone give me a full description of this t


I usually replace icemakers as a unit. It sounds like the mold heater is out. The system cycles like this: Fill, freeze, mold heat, eject, and start over. The mold heater not working will prevent ejection. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Water stays in the top draw filter area, have checked hoses found good connection and no kinks in the lines , could this be a pump motor problem. I have had a problem the first month with this unit and the tech. replaced a lot of parts including the computer for the top draw . i am now out of warr. time not by much and am starting to get upset that this problem is happening after such a short time.


... Fisher and Paykel DS605I Built-in Dishwasher

I have kenmore dishwasher model no. 665.1371 I'm getting a leak just under the door area the connects to dish washer are good, there is white plastic unit the water line is hook to is dripping from that area but I can't see were it is coming from sometimes it stop on it's own for a couple of weeks and starts up again. Thank you your time


... Kenmore Dishwashers

Bosch Dishwasher has error code e24, I checked the line, replaced with new pump, new control unit and call repair man no luck. It works on and off. I get it run then next cyle nothing. Heelp!


... Dishwashers

Water level What should the correct and/or optimum water level be in the tub of this dishwasher for proper operation? There is water in the bottom of the dishwasher after the cycle completes. 1)checked the hose, it is not kinked 2) not hooked up to a waste disposal. What else could it be??


Some water in the tub after the cycle is complete is normal. most dishwashers are time filled with a float switch as a safety device. the actual level depends on the fill time and the water pressure. what exactly is the d/w doing (or not doing) to ma ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

Unit won't pump out, checked the lower impeller and it was very loose, is there a drain valve on this unit? Model 587.14249991 The upper impeller is a fixed unit right to the motor but it appears the lower impeller is a push fit over a rubber sleeve. I only saewa check valve in the drain hose, is there any thing else I should check? hose is clear and the switch for the float is working ok.


At the bottom of the unit where the hose goes is a check valve. check to see if clogged. ... Dishwashers

The water discharge line is connected to a unit that is mounted to the sink. This unit in turn has another line that is connected the the house drain. This unit is sparying all over the sink, counter and floor. What is the purpose of this unit and why couldn't the drain from the dishwasher be connected directly to the house drain?


It is a unit to stop water flowing back into the Washer... I suspect it is blocked... You probably need a Plumber? ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0927 seconds