Having problems with your Dishwashers ?

Our Frigidaire dishwasher, Model # FDB2410LDS0 has power and will start on any cycle, but after filling with water, there is a pause and then the lights just start blinking and it stops at around the 92 mins remaining display. We have tried shutting the breaker off for 10 mins, then back on, hoping to reset it with no luck. Any thoughts?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Frigidaire dishwasher, Model # FDB2410LDS0 has power and will start on any cycle, but after filling with water, there is a pause and then the lights just start blinking and it stops at around the 92 mins remaining display. We have tried shutting the breaker off for 10 mins, then back on, hoping to reset it with no luck. Any thoughts?


... Dishwashers

GE GLD6360L15SS. Dishwasher stopped mid cycle and the Start / Reset button is flashing. The washer will not restart. Tried unplugging for 1 min and flipping breaker for 1 min. No change.


... GE 24 in. GLD6360LSS Stainless Steel Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have F&P DD603 with problem with bottom draw. Once a programme is selected and door is closed, the dishwasher beeps three times then tries to start itys cycle. It then starts but stops every 1-2 minutes (like pause botton has been pressed). If you press start again it starts for 1-2 mins then stops again. I have tried turning off the power and totally cleaned out the dishwasher but no change? Any suggestions?


Hi \015\012When you pull out the drawer, pay attention to the bottom near the bottom front panel, you will see a little tab. this tab is at both sides of the drawer, press these tabs in and pull the drawer fur ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

My Frigidaire model GLD2155RDC1, installed in 2007, stopped working after we lost power. When we flipped the circut breaker back on the lights for Air Dry and High Temp Wash started blinking, but none of the other buttons work and when we open the door these lights stop flashing and there is no power for our machine. We tried tripping the breaker a few more times and it kept doing the same thing.


... Frigidaire Dishwashers

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

I have a Bosch SHU66C02. I opened the door to stop it from running temporarily, while it was sitting not running, it leaked all of the water out of the bottom right corner of the door, and when I went to start it later it just hummed but the timer didn't go down for over an hour. I tried to put more water in but as soon as I started I could hear the water added to drain. I turned the breaker in the fuze box off to it and let it sit for over an hour, but when I restarted, the timer was still at


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. Thanks


... Whirlpool 24 in. GU3600XTRY Stainless Steel Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

I just got a kitchen aid regency portable dishwasher. My guess is its around 20yrs old. The problem is after i push the button to start it it flips off the breaker in the house. I tried different plug ins with the same results. I starts with the red light on and begins the soak process but when it gets the the rinse....click thanks Dallas


Really sounds like the water has leaked into some part of the machine and is shorting out the electric, or, some part has frozen up. By all means, do not use this machine until it is fixed, or you may actually start a house or apartment fire. ... Dishwashers

Sears Kenmore UltraWash Dishwasher(665.16464300) wont start. "SMART WASH" and "NORMAL WASH" buttons blinking. Already tried unplugging for 10 mins and also checked circuit breaker.


Hi\015\012\015\012\015\012I believe you were advised what could be bad and all the possible solutions about your Dishwasher still you rejected the solution. I dont think its fair when someone helps you for 40 minutes.\015\012 ... Dishwashers

The cycle started then stopped after 10 min. There is water in the bottom and no lights will come on. There was no breaker tripped.


Circulation pump needs replacing call 1-888-nyc-1055 this company repairs all bosch seimens thermador and Gaggenau units. ... Bosch 24 in. SHU5305UC Built-in Dishwasher

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

I own a kitchenaid dishwasher model KUDPO2FRSSO. The normal and cancel lights are flashing. I have tried shutting off the breaker for 20 min. Plus only to have the cancel light stop flashing but the normal light continues to flash. An


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

MY DISH WASHER STOP IN THE MIDDLE OF WASH DIDN'T DRAIN NO SIGN OF STARTING NO LIGHTS NO NOISE. WE TRIED THE BREAKER TO RESET AND NOTHING HAPPEN


Hi\015\012\015\012\015\012Check if there are any lights blinking or any error codes that are being displayed on the panel. If reseting the breaker didn't help then check the wiring to the power socket, try pluggi ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

I have a KitchenAid dishwasher model KUDKO31TWHO. Only the cycle light comes on blinking but will not allow me to start the cycle.All it does is blink. I throw the breaker to get it to stop and try again but nothing works. Help


... KitchenAid Dishwashers

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1475 seconds