Having problems with your Dishwashers ?

The F4 fault code on my Fisher and Paykel Dishdrawer Model DD603 dishwwasher indicates that the "temperature sensor is faulty. Question: where is it located on the machine and how do I replace it?


Answers :

The temperature sensor is located on the heater plate(looks like a blob of solder with a thin line leading to a blob of solder,The solder acts as a fuse when it "blows"you have to replace the heater plate.The heater plate is located in each draw (get at it from the underside of the draw)there is a grey round plastic piece that has to removed like the back of a watch.Caution you shoild have the power and water off and this is a job best left to the capable!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The F4 fault code on my Fisher and Paykel Dishdrawer Model DD603 dishwwasher indicates that the "temperature sensor is faulty. Question: where is it located on the machine and how do I replace it?


The temperature sensor is located on the heater plate(looks like a blob of solder with a thin line leading to a blob of solder,The solder acts as a fuse when it "blows"you have to replace the heater plate.The heater plate is located in each draw (ge ... Dishwashers

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring The solution I tried didn't clear the error code on the panel. Is there a reset or do I need to replace the aqua sensor or ? The machine still won't start and displays a #1 on display. There is no water in the whi


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a Fisher and Paykel DD605i dish drawer. We have a U1 error code on the top drawer and had this same problem just over a year ago. A repair person replaced the inlet valve I believe. I am wondering if there are any tests I can put the machine through or if this is something I can fix myself to see what is causing this code.


... Fisher and Paykel DD605I Dishwasher

Hobart lx30h replaced all sensors and have no more error codes but the machine says fill but never fills and wont turn on wash cause it thinks its filling...any advice?


Are you sure that you have all the connections rights? Did you check the voltage at the water fill solenoid? ... Dishwashers

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

DS603 Fisher & Paykel U1 error code ..(see our previous errors we've listed) we have now pulled out the yellow water valve that goes up behind the front panel and at the other end by removing the drawer and plastic protector thingy - we checked that there were no bedris or calcium buildup in the valves ends and filters and replaced it all. So we put it all back to gether as we could not see what would cause this error, only to find that it worked - water came into the machine but about 4 mins in


This product is total ****.\015\012Pull it out, call whoever sold the **** to you\015\012and tell the to come get it and shove it up their ***.\015\012Then buy a Bosch and live a happy life.\015\012The design is moronic. The machine is like the old\ ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring


As long as it is sealed and you should also make sure there is not water in the white plastic pan under the dishwasher.. ... Bosch 24 in. SHU43 Built-in Dishwasher

HOOVER HED60-86 Dishwasher Error Code: Temperature Sensor Failure


... Dishwashers

My Hotpoint FDW20 dishwasher does not heat up and is washing cold. Could you, please, suggest a solution to the problem. Can you also forward me a circuit diagram for the machine along with a manual with the location of various sensors, switches and other electrical components and the wire colouring to these components. I am an electronics engineer by profession so if had a circuit diagram and a legend of the various sensors and switches along with their location on the machine it should be pos


Hi,Check your heating element.. \015\012A bad heating element causes many problems in dishwashers...Dishwasher Problems The Heating Element n ... Hotpoint Dishwashers

We have a Katcher HDS 3.5/30-4 M Ea. Was using it, stopped using it briefly in the middle of a job, pulled trigger again, and there was a lack of pressure. Went to the machine to troubleshoot. The "engine indicator light" is on. Checked the temperature of machine: fine. Water intake: fine. We have not been running it at high temperatures, but about 50 degrees C. The pressure was at about 2300 PSI before it stopped. Any ideas?


... Karcher Pressure Washers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

Leaking dishwasher leaks intermittently. I removed the side panels and there is no sign of water in the base of machine. Door seal seams to be intact. What else can I check. Seal that needs replacing? Machine is 18 months old. seams to leak on the right side of the machine. Please advise. many thanks. My dishwasher showed the error code either OE or E1, I think it was more OE. I stuck my hand in the filter in the bottom of the machine and then it was okay but the next time it was used it leake


What sort of soap powder do you use\015\012some soap powders foam a lot in machine causing dishwasher to leak through seals\015\012also check that the machine is square that is the door is closing parallel with cabinet\015\012do no ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Bosch SKT5102 The machine wont stay on. When I push the on/off switch the machine comes on for a split second then goes off. If I hold the switch in then the machine works. I have taken the back off and located the micro switch and note that I can buy a replacement. Do you think that is the problem and will I just be wastin my money on a new switch if not. Thanks


It sounds like the switch but you don't need the bosch one if it is only the micro-switch they are easily available\015\012ger531 ... Bosch 22 in. SKT5002GB Built-In Dishwasher

Optical water indicator (Turbidity Sensor) failure - FA error code


... Dishwashers

Temperature sensor failed error code kitchenaid KUDD01DSSS


... KitchenAid KUDD01DSSS Built-in Dishwasher

My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem


The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher

I bought an IKEA Renlig DW60 dishwasher about 6 months - the controls are located on the inside top of the door. Ordinarily the dishwasher turns on and three red LEDs on the far right of the control panel light up. On occasion however only a single red LED indicating the temperature of the last wash I carried out will go on (it is always the 50 degree light as this is always the wash temperature I use). When this happens the dishwasher appears to be stuck and will not start when I shut th


Press and hold the cancel button for about 5 seconds. This resets the electronics and gets it going again ... Dishwashers

Flood sensor location fisher & paykel DD603 - Fisher and Paykel 24 in. DD-602 Built-in Dishwasher


... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Intermittent problem with error code E 01, which tells me there is a leak. However, I have turned the dishwasher on its side and back and am certain that the pan is empty. Indicates a false error code or sensor. How do I fix that or disable it?


... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Dishwasher FDB4315LFC0 Error code ER uo Second time it has happened. First time, a repairman came and said I needed a new "vent assembly", but I asked if he could "un stick it," so he took it apart and fiddled with it, and it worked for about a month. Now the error code is back, and he warned that if it came back, I should have it replaced. I've only had this NEW machine 10 months -- this shouldn't happen, right? Any suggestions? Thanks.


Who's to say what should or shouldn't happen?Sounds like you need a new vent assembly. ... Frigidaire Dishwashers

Bosch dishwasher shu4322 has code 1 aqua sensor what is the sensor do and where is it located


Most of the dishwasher has a Thermal hold period in which the machine will not advance to the next cycle until the water temperature reaches a specific degree. it is possible that your aqwa sensor/or heater is bad OR as in most of the cases, the Time ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Good morning, I have 01 Hobart dishwasher AM14, i need to be replace rinse sensor probe and temperature sensor for booster heater.But I can't to find Hobart part number Please help me.Thank you.


294692 for the rinse probe.\015\012"temperature sensor for booster heater"? Do you mean the thermostat? If so, part number is 274161.\015\012\015\012Parts breakdowns and part numbers are available at ... Hobart AM14C-155 Dishwasher

E4 code, Can't stop the machine trying to empty. There is no water in it, have even tried fooling it by putting water in. Error code shown is E4, which indicates overfill, but that is not the case. Help :)


... Baumatic 23 in. BDW9 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0905 seconds