Having problems with your Dishwashers ?

No water in wash - Dishwashers


Answers :

Make sure that the inlet has the flow of water- remove the inlet to check. when the program is triggered if there is no flow it is possible that the inlet valve is faulty specially if voltage comes on the valve without a function. Dirt could also be clogged in the valve- if so clean and reset. If there is no voltage then the program controller is faulty.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

I have a Siemens dishwasher serie IQ which has had water damage. There has been water pressure on the drain tube. Probably the mashine has been partly filled with drain water. Now it can start and pump out the water, but it never starts any washing program. Well it starts and the time left (e.g. 15 min on the shortest program) is displayed. But then it does not start to wash or count down. Any idea what is wrong or broken? Anyway I can repair or reset the dishwasher?


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

I have a hotpoint aquarius df23 dishwasher. when i turn it on for a wash there is no water coming into the dishwasher. i have put water in with a bowl and it works as normal until it drains the water out. my washing machine is plumbed in to the same pipework and it is working fine. does the dishawasher have a water pump that may need replacing????


Most likely you have an air lock in the dishwasher.\015\0121. Refill the salt compartment.2. Turn of the water supply at the mains.3. Disconnect the diswashers water hose from the mains supply.4. Lower the water hose and allow ... Dishwashers

Diswasher TYP NBKH, SERVICE 8546 892 10010 Problem: For all programs except rinse and charge 1/2 for all programs. Pre-rinse and rinse for 50 Bio, 60 and 70 OK. Downloading water to wash causes multiple knocking (on the left side dishwashers) and simultaneous blinking light (relais?). Opening doors and adding water (different amounts - from 0.5 to 2 l) brings the normal work of dishwasher back. Rinse with cold water after washing OK. Final cleaning with hot water causes knocking again. After r


... Dishwashers

Frigidaire fdb1500lsfo built in dishwasher. Have had for maybe 3 years. I push the start button, and it starts like usual, filling the tub with water. After filling, it will not do anything for about 5 mins, where then it drains. It seems to go through the whole wash cycle, but after it has pumped the water out. Dishwasher steams all of the dishes, but there is no water in it to wash them with.


... Frigidaire FDB1502RG Built-in Dishwasher

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

Do these 'portable' dishwashers 'heat' water prior to washing? i have customer complaining bout the dishes not coming clean..yet the water entering the dishwasher is cold, does not appear to heat water prior to washing.


Most dishwashers require a minimum 120 degree inlet water temp. The heating element will boost this up during the main wash cycle to aprox 140. Do not hook a dishwasher up to inlet water temps above 150. ... GE Hotpoint HDA3500N Dishwasher

Dishwasher makes grinding noise during wash cycle (after pre-wash). noise persists for 15-20 minutes. It seems as though the inlet valve doesn't open during this phase of the cycle. adding water to the dishwasher manually eliminates the noise and water circulates through the wash arms. I'm trying to determine if this is a controller issue or a valve/pump issue.


Water-inlet valve\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012\015\012\011\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\01 ... KitchenAid Dishwashers

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

My fisher & paykel dishwasher won't empty water after washing and rinsing. Water overflowed from the dishwasher then remained in the bottom. I can hear the pumpt trying to pump. The dishwasher


... Fisher and Paykel 24 in. DS603H SS Free-standing Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Frigidaire Dishwasher This is my second dishwasher in 18 months. Water leaks out the bottom of the dishwasher. It did it on my first one now it''s doing the same thing.Could it be the water pressure from the city water line? How could this happen to two dishwashers in a row? The leak starts immediately when the wash cycle starts.


This is a simple solution, the brass nut that connects the heating element to the base of the dishwasher is cracked and needs replaced. It takes just a few minutes to replace, just remove the nut after TURNING OFF THE POWER and take to your local par ... Dishwashers

Leaking dishwasher There is standing water in the dishwasher when it's not being used. Recently we had a garbage disposal installed and was wondering whether this may cause the water from the sink to settle in the dishwasher. Also, the water rises and leaks on the floor. We have to run a wash cycle to drain and dry out the dishwasher. What do you think the problem is?


It sound like while the assembly of the garbage disposal, you placed the end of the drain line pipe in a lower position than it was before.\015\012Good luck! ... Kenmore 15129 Built-in Dishwasher

My Bosch dishwasher is Exxcel 5 prg model no SMS50E020GB. When you first open the dishwasher door after the washing cycle finishes there is no water in the bottom of the dishwasher but about 45 minutes later water slowly appears in the bottom of the dishwasher. I scoup out the water and there is about 3 litres. The machine is just over 2 years old. I had a plumber check the machine and he couldn't find anything wrong with the machine. Another plumber came out and put on the invoice: "disma


... Bosch Dishwashers

ASKO 1885 Built-in Dishwasher: The water sump fills normally, but the wash cycle does not start. Althought the timer seems to work, the wash cycle motor won't start up in any wash or rinse selection. The spray arms do not spin - no water is being pumped. At the end of the wash cycle time, the water will empty out of the sump. Thank you. TB


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1885 and 2) filling ... Asko 24 in. 1885 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1362 seconds