Having problems with your Dishwashers ?

I have a Haier DW12-PFE2-U Dishwasher that has a fault code flashing the first 4 programme lights(J1,J2,J3,J4). The instruction manual does not tell me what the problem is but it may be the water inlet. I have checked the supply and waste both are okay! Any suggestions?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Haier DW12-PFE2-U Dishwasher that has a fault code flashing the first 4 programme lights(J1,J2,J3,J4). The instruction manual does not tell me what the problem is but it may be the water inlet. I have checked the supply and waste both are okay! Any suggestions?


... Dishwashers

I have an LDS5811 and I just started getting an IE error. The manual says its a water inlet problem. I have not moved the unit since installing 3 years ago and have not disturbed the water supply. I checked the inlet tube and all appears OK. Any other suggestions?


I have had this error occur often due to faulty flow meter -remove left hand side panel, there is a large plastic component with three wires(red, white, black), these wires go up and connect onto main control board. Check these three thin wires for b ... LG Dishwashers

Model: Whirlpool ADP 4501/5 (4 years old) Problem: Dishwasher won't start wash cycle. Green light flashes 11 times. After adding a bucket of water to the dishwasher it runs normally. Checked the inlet valve and it appears to be fine. Filled the salt container and it solved the problem for a while but having the same problem again. Any suggestions would be appreciated.


... Dishwashers

My SE53200GB/01 fails to input water. I have checked the inlet supply hoses and filters and they are clear. I have tried different programmes and they all activate but the water fails to enter the main chamber. Any ideas what may be the problem. Could the Aqua-Stop mechanism have kicked in and if so, how do I rectify it? Thanks


Your aquastop system is activated :deactivate by turning off the water supply, running the dishwasher so \012that it is expecting to fill (if you hold the grey square box at this \012point, you should feel it slightly vibrating, which is a good sign ... Siemens Dishwashers

After it cycles I open up dishwasher and the soap tray is open with soap leaking out and on dishes. How can I tell if this is a problem with float switch or water inlet valve because I think it's not getting any water? have maytag MDB3700AWE. also checked to make sure nothing stuck in float.


Try this link it should help http://appliancehelponline.com/dishfloatwaterinletvideo.html ... Maytag 24 in. MDB4600A Built-in Dishwasher

Lg dishwasher model LD-2163SH problem code IE meaning water is not supplied. I have checked that the valve is open and water line has sufficient pressure. Inlet hose is also not kinked and pump for drain is functioning normal. Pl suggest solution urgently? manoj


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

Dishes on top rack are not getting clean. the spray arm does rotate when I spin it by hand, but not sure it is spinning when door is closed. Water is present on the spray arm when I open the door to check. Can you suggest things I might check or tell me what may be occurring?


Remove the spray arm and clean each nozzle then fixed it back and test but be sure that the wash pump is working. ... KitchenAid Dishwashers

We have a Brandt Aa Class Dishwasher that will start and run the fill cycle for about a minute with the red operating light on but then stops and the red light goes out. I suspect it may be a timer related problem but can you tell me where the timer is on this model ? I have checked the filter and that the water supply and drain hoses are not kinked.


... Dishwashers

I have a bosch diswasher shu42lo5uc. The dishwasher will not fill, the water inlet solenoid may have failed, or what else can I check to find the problem


... Bosch 24 in. SHU42L05UC Stainless Steel Built-in Dishwasher

I have an LG dishwasher that keeps giving an 1E error code. The code means water inlet trouble and recommends the following. Check clogging of water inlet hose(or hose twist or freezing) Check if it's suspension of water supply The problem doesn't seem to be either. ?


Try replacing the water inlet solenoid valve (it may have an open coil). The water line goes directly to it. ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a hotpoint aquarius DF22, problem: machine not taking in water to commence the cycle, (this is intermittent and worked sometimes) the plumbing has been checked regularly and for a time would start after reconnection, the motor is fine the electrics have been checked by a qualified electrican who cannont source the problem, now the machine will not take in water at all, any suggestions please?


... Dishwashers

We are having a problem with our LG Dishwasher. The machine is washing for about half an hour and then will stop and report an E1 error. According to the user manual this means "Water leakage in Hose connection" or "Water is leaked by damages". We have checked the diswasher's water connections and can't see any water leaking out. We have also cleaned the filers and checked the spray arms but that has not made any diffrence. Any suggestions what this error means and what we can try to resolve it


... Whirlpool 24 in. DU940QWD Built-in Dishwasher

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher

Water inlet valve the machine wont fill with water. checked all hoses, but water inlet valve ma;y be sensitive how much are they to replace. could this be the problem?


A water valve is anywhere from 15$ to 43$ depending on make and model ... Dishwashers

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!


Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

I received the IE error code (Water inlet trouble) on my LG dishwasher. I've checked the hose and the water flow into the machine and there is no problem there. Where else can I check?


... LG LDF6810 Built-in Dishwasher

IE message Getting an IE message on dishwasher. Water is coming into the tank and heating, but after about 5 minutes, it kicks into an IE error. We have checked the water inlet and the spray arms and everything appears okay. I have read the comments about checking the float, but how do you do this? Any other suggestions would be helpful.


My solution was, after LG sent me a second dishwasher that ALSO did not work, to demand a refund. Then I went and bought a KitchenAid~ it's awesome! ... LG LDF6810 Built-in Dishwasher

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

Candy csd-68-80 all four lights on front panel lit, started flashing within few seconds of switching dishwasher on, no previous problems,dishwasher not overfilled, checked manual which said too much inlet water unsure what this means or how to check it. do all usual cleaning,salt,arms etc. had dishwasher about 14 months and use it every day never had any problem before


... Candy Dishwashers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

My 13 year old Frigidair dishwasher (model FDB221RFR2) is not disolving the soap tab that drops in during the later cycles. We sometimes find the soap sitting on dishes or on the bottom. It appears that there may not be enough water but I'm sure of how much there actually should be. It also appears that the soap may be dropping late but again I'm not sure of when it should normally drop. I checked the inlet value and it appears to be ok. I also checked the timer (to the best of my ability) and i


CHECK YOUR WATER TEMP, IF ITS NOT HOT ENOUGH SOAP WILL NOT DISOLVE. I HAVE ALSO SEEN INTAKE VALVES DROP OUT LATER IN CYCLE. THAT MAY BE YOUR PROBLEM. GOOD LUCK! ... Dishwashers

Kenmore dishwasher 587.15163401 won't fill. I checked the float switch with my multimeter and it's working properly. It's registering zero when I touch the terminals and 1 when I activate the switch. On this particular washer, how do I access the water inlet valve to check it for debris and also to check the solenoids? Also on this particular washer, how do I access the drain valve and solenoid. Can you tell me if this is a single direction motor or reversing motor. As I understand


The problem was the water fill valve. When set to Ohms, the multimeter never would read zero indicating a problem with the water fill valve. I replaced the part and it works now. Be sure to turn your water off under the sink before taking it off t ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1148 seconds