Having problems with your Dishwashers ?

Bosch dishwasher model sgs43c02gb/35.no lights on front panel will not run but power getting to machine


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch dishwasher model sgs43c02gb/35.no lights on front panel will not run but power getting to machine


... Dishwashers

My dishwasher was running (Model # MDB9150AWB) was running and stopped. No lights on the front at all. Checked, and it is getting power from the 110 line at the connection to the wires in the lower (stationary) panel. Any thoughts on whether there is a circuit board that needs to be replaced?


... Maytag MDB7100AWB Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

My GE Profile dishwasher (model PDW9880L00SS) has an electrical problem. Last night, the dishwasher was beeping and the control panel lights were bouncing around as if someone was pushing the buttons. I managed to get it to run a cycle, and now the control panel is completely dark.


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

My KitchenAid Model KUDE70FXSS 2 dishwasher is new to us today and has never been used before. It was hooked up professionally, but I assumed it would work, so tonight when I tried to run it, it lights up on panel, but it won't run any cycles. It will start putting water in the machine, but then cuts off. It starts making a grinding noise underneath the machine, and it clicks like it is trying to work, but the water doesn't wash. Hmmm. Anyone know what to do?


... KitchenAid KUDE70FXSS Builtin Dishwasher

We have a Bosch dishwasher SHX46A06 UC/21. It continually runs. We couldn't find a diagnostic test for our model, but we did for another model. We held down the power scrub and regular wash cycles then turned it on and pressed them again. The delicate/econo light started blinking. Looking at some of the blogs, most often it seems to be the heater or the control panel - does this diagnostic test help to pinpoint what could be wrong? Also, where can we find a good manual for our model - we're havi


Here is a link to the service manual http://cgi.ebay.com/Bosch-Dishwasher-Service-Repair-Manual-/250480379703. \015\012 ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Hobart lxih everytime i add soap i get a service code e4 and the machine stops shut the machine off and it restarts just fine add soap and shuts down i use a powered saop made for under the counter dishwashers even when i run a delime agent thru the machine it the does the same what to do thanks for help david


E4 indicates water level has not reached top water sensor. Check for proper flow-water pressure to machine (15-25psi) and clean sensor in wash tank ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Kenmore dishwasher I have a kenmore dishwasher and in the middle of a cycle all my front panel lights went off. I have checked the power going into the dishwasher it is fine. I also checked the door latch it is fine. Not sure what else to check? Same exact problem model number 665.15934 We have had nothing but problems with all of our sears products - highly suggest to SHOP SOME WHERE ELSE before you get stuck too.


Check the continuity of the thermal fuse (part # 8193762). It's clipped onto the electronic control inside the console.Let me know if you need more help. ... Kenmore Dishwashers

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 ... Amana Dishwashers

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

The control panel on the front of the machine will not light up and will not activate any of the functions on the dishwasher. The machine is getting power into the main connection box.


Hi,\015\012 \015\012Checked whether you have accidentally locked the control panel or not, push and hold the 3 key for 5 seconds and the dishwasher will activate. \015\012OR ... Dishwashers

As the dishwasher was finishing its cycle - up to drying - three small explosions occurred accompanied by the smell of burning. We turned the power off. Is it repairable or is it time to get a new machine? The dishwasher is nearly 10 years old Model PL 660X semi-integrated.


Well its up to u about getting a new one but it sounds like the heater element burnt into but yes it is repairable but at what cost unless u can repair it your self u may be able to save money on repair costs if u have to call a repair man then it ma ... Smeg Dishwashers

A screw fell in to the bottom of my dishwasher. In trying to get it out it disappeared. In trying to find it we found another one that looked like it had been there a long time. My dishwasher is old model #DU920GWBD5. Do you think we can run the machine?


... Whirlpool Dishwashers

Dishwasher model: DU1100XTPQ1 The dishwasher started it's cycle and then just stopped. Now none of the lights come on in the front panel. I've tested: 1) Electrical power to the machine checked OK. 2) Two switches inside the door handle show contenuity when depressed.


HI. Your testing has confirmed that the main electronic control board has failed. This will cause an abrupt shutdown. There is a fuse located on the control board. it is mounted on the back side of the control board. test the fuse for continuity. if ... Whirlpool Dishwashers

Thermal fuse Dishwasher konked out mid-cycle and now no power to control pad. We've already had the thermal fuse replaced once (machine is only 2 years old!) and this appears to be the same issue. I tried to open the front and I think I can see where it is but not sure how to get it out and replace it AGAIN. I wasn't able to get the inside panel completely apart from the front of the unit so I was somewhat limited. I'd rather save the service charge if I can and there's n


Http://www.partselect.com/MultiModels.aspx?ModelNum=KUDS35FXSS&SearchTerm=fuse&RefineSearch=0Maybe this link will help ... KitchenAid KUDS35FXSS Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

When I try to start the dishwasher, I can get the light to show I want it do do a normal load. Then when I hit the start button, it lights up but the machine will not sstart. Then in a few minutes the lights on the control panel at the top of the door go out. What can I do to fix this? The model # is KUDS011JBS0 tHE 0'S HAVE A SLASH ACROSS THEM THE TYPE IS 577-0 SUPERBA


Hi,\015\012\015\012Your control board has gone bad... you will need to replace it.\015\012The replacement is not very hard, just make sure that you mark where all of the wires go before removing them.\015\012\015\012Here ... KitchenAid Dishwashers

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2594 seconds