Having problems with your Dishwashers ?

My Bauknecht GSFK 2351 dishwasher would not start the washing cycle.rnThe green light flashes 6 times repeatedly. I was able to drain it by pressing the 'reset' button for several seconds. The filter is clean, no obstruction seen.


Answers :

Hi

Please check if the green light flashing 6 times. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry. If this doesn't work then its an issue with the heater circuit, door switch, wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back for further assistance.

Daniel
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bauknecht GSFK 2351 dishwasher would not start the washing cycle.rnThe green light flashes 6 times repeatedly. I was able to drain it by pressing the 'reset' button for several seconds. The filter is clean, no obstruction seen.


HiPlease check if the green light flashing 6 times. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this erro ... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

My asko D3531, has a problem. The message panel is blank. When I turn it on, it sounds like it is draining, but there is not water in the tub. I cleaned the filters and didn't find any obstruction. When I press the start button for 3 seconds as directed in the manual, nothing happends. I can't get anything to come up in the LED display. Please help.


I have the exact same problem - Cindy did you ever figure it out? Please let me know.Thanks ... Asko 24 in. D3530FI Built-in Dishwasher

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

Maytag dishwasher. The clean light stays on solid until I press any button then it blinks for several times then goes solid again. None of the other buttons light up when pressed. I unplugged it for over an hour to try to reset it but that did not help.


... Maytag MDB9600A Jetclean II Built-in Dishwasher

We have a Beko DWD5410W dishwasher that has worked fine...until today - the 'wash' light is on but it is not wasing. I have pressed in the 'start' button and held for 5 seconds to reset and it then springs to life draining out or whatever that noise is, and then if I turn the dial to a setting (even the cold prewash) and press 'start' again it starts whirring away, then after about 10 seconds just stops, with the 'wash' light staying on. Not blocked, I have checked - this likely to be a frozen p


... Dishwashers

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

My Frigidare GLD2250RDB1 will not drain. When I press the Cancel button it just clicks. Also, when pushing the Normal Wash button and Start it is very delayed in starting. I have turned the power off to the dishwasher to reset it, but it does the samething. I have cleaned the screen in the bottom of the dishwasher.


Control board failure is monster problem with the entire line of Frigidaire dishwashers.Secondly the drain pump could be bad. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Our Bosch dishwasher #SHU9922UC (FD8007) will not turn on properly. Only its drain pump starts -- and keeps running -- when it's powered on and the door's closed. Pressing the two "drain cancel" buttons for more than 3 seconds doesn't help. Neither does cutting off power, then turning it back on in the hopes of resetting the machine's 'computer'. No water inflow occurs. Help?


I had a similar issue after I replaced a bad drain pump, seems the logic got hung up.. I poured in a pitcher of water, closed the door, it drained and was then ok - worth a try. If not, you may have a bad water level switch. ... Dishwashers

I have a miele g892sc+. The train/intake light comes on and holding the start/stop button for five seconds does not reset. I've cleaned the filters. But it appears to be stuck trying to drain. Since the reset doesn't seem to work it's hard to tell if that would 'fix' the problem or if there is actually something else wrong.


The END, START/STOP & TOP SOLO all flash at same time ... Miele G892SC SS Dishwasher

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

Model No KFID 60A Dishwasher I have tried to reset but only spraying .I have followed instructions to reset. Press start button for 2 seconds until light goes out. Leave to drain then start a new programme. Still only spraying.


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have a Kenmore Elite Ultra Dishwasher and the cleaning light is flashing. I have tried pressing the start/resume button and closing the door within 3 seconds. I am not able to turn on my dishwasher. I have tried turning off the power for 20 minutes but when power was restored the green light continues to flash and the dishwasher will not work. This machine was installed in May 2008. Help!


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Dishwashers

My frigidaire dishwasher (FFBD2405KB) is not working... when I press the wash button, it will blink, but nothing happens. I've tried it on all settings, but nothing works. It's obviously getting power since the lights are working. I've cleaned the drain thoroughly and made sure there were no obstructions. Any ideas?


... Frigidaire Dishwashers

I have a Whirlpool GU2700XTSB1 dushwasher. It stopped one day and cleanning light was blinking. I was able to reset the dishwasher by pressing two of the button 3 times. Now when I run the dishwasher it fills the bottom with water, heats the water and then buzzes. The wash motor does not spin. Any help?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Lamona dishwasher all light are on and have cleaned filters and tried resetting pressing button for 3 seconds


... Dishwashers

Kitchenaid kudc03fvss0 dishwasher stopped mid cycle without drying dishes last week and then stopped altogether with lights flashing and full basin. I disassembled filter/pump cover in bottom and cleared several plastic pieces and cleaned chopping blade and screen. After unplugging/plugging and pressing cancel button the pump runs for about 10 seconds and stops with normal and heavy duty lights flashing. What should I check next?


... Dishwashers

In order to reset my dishwasher i was told to alternatively press the clean and rinse button. my dishwasher has no button that says clean, rinse, or clean and rinse. my button choices are as follows: Front: CANCEL and START/RESUME Cycles: HEAVY DUTY, NORMAL, LIGHT/CHINA, QUICK CLEANUP, or RINSE ONLY Options: PROSCRUB, HI-TEMP SCRUB, SANI RINSE, HEAT DRY/Lock symbol, 4 HOUR DELAY. Does anyone have the correct sequence for initiating the diagnostic cycle?


If you want to reset the computer in that dishwasher you can just unplug it for a half hour. if it is a built in just locate the fuse in the or breaker that the dishwasher is on and pull it for that length of time. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

My brandt VF300 doesn't drain at the end of wash cycles. If you run the soak programme it drains fine. Some time ago the door was adjusted by an engineer, when he arrived he pressed some buttons which then drained the unit immediately, I have forgotten which buttons! Is there anything I can do to reset the thing, given it drains on soak I am doubtful the drain pump has broken ir is blocked?


... Dishwashers

I have an older GE dishwasher, model GSD1200T02. I recently put in the wrong soap, so I had to press the clear/reset button. When I did this, the dishwasher ignored me and seemed to continue through the cycles anyway. When it got half way between "drying" and "off", it stopped, and has been that way for several days now. It will not respond to any button pushes at all now. I cannot even reset it because it does not respond at all when I press the clear/reset button. I have had a load of di


This is only a long shot, try turning the breaker off and on again, may be ???\015\012 Jacques. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1969 seconds