Having problems with your Dishwashers ?

Telmann Dishwasher TEL 12DWM. Dishwasher started to make weird wooshing start-stopping sounds at the beginning of the wash cycle so I stopped it. Since then the lights are on but wont go regardless of where the switch is set to. Have pulled the pump off and the inlet pipes and blown to remove any blockage but still no luck. Cant get into the water jet part due to connectors that require specfic tools to remove and replace. Any thoughts?? thanks in advance, Michael


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Telmann Dishwasher TEL 12DWM. Dishwasher started to make weird wooshing start-stopping sounds at the beginning of the wash cycle so I stopped it. Since then the lights are on but wont go regardless of where the switch is set to. Have pulled the pump off and the inlet pipes and blown to remove any blockage but still no luck. Cant get into the water jet part due to connectors that require specfic tools to remove and replace. Any thoughts?? thanks in advance, Michael


... Dishwashers

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

How do I remove the main conduit on my GE Triton XL dishwasher? The cover inlet that traps food from going down the drain somehow came off and clogged up the drain. I got the drain cleared but cannot get the cover back on and need to move the main conduit (pipe connecting lower and upper arms) before I can get it on. Anyone know before I spend too much $ finding someone to fix it?


... GE Dishwashers

I have a candy trio 501 dishwasher with intergrated oven. When I put a cycle on it starts its first rinse then after 5/10 mins stops and beeps constantly. It's still full of water too. When I put it on rinse cycle it compleates the cycle so inlet and drainage should be ok. Ive removed drain pipe and made sure its not kinked and also clear. I've removed and drained the compartments that had water in and also blew down the pips to see if clear all ok. I've checked the heater element with meter and


... Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Bosch 24in. SGS69LO2 Logixx Our machine runs but there is no water coming into the machine?have removed pipe to check water flow,ok, have removed the filter for the inlet supply,clean.have cleaned all filters and replaced, reset the programs, but still no water into machine.


... Bosch 24 in. SGS69L02 Logixx Built-in Dishwasher

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

Bosch aquatech dishwasher will not fill with water and displays code F in the wash time display window. Removed blockage from the inlet supply pipe, but machine still does not fill


... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I am having trouble attaching 90 degree brass elbow to the plastic water inlet on my new Maytag Dishwasher. Getting leaks. Teflon tape hasn't worked. Cant seem to get the washer to seat properly when everything is tightened down. Wish the water inlet was not made of plastic. It appears it would seat the gasket properly if the water inlet was made of something more durable.


Hi!!\015\012\015\012Have you tried pipe cement, the plastic to metal kind will take care of any leaks. You can find it at any hardware store.\015\012\015\012Good luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly app ... Maytag MDB8959AWS Builtin Dishwasher

Model # gsd3320c04bb. I am getting water to the inlet valve. I tried changing the inlet valve but still no water goes thru it. I am getting 22 V AC at the connector when operating. The only water that is circulating in the dishwasher is the water that is remaining in the pump system. Any ideas as to what is preventing the inlet valve from operating?


Sounds like you need to replace the mixing valve which is where your incoming water lines connect to the back of the washer. ... GE 24 in. GSD3320 Built-in Dishwasher

A glass shattered in a thousand pieces in the dishwasher. I cleaned and vacuumed everything except the very bottom that I can't get to. I took out 8 screws, removing the round rotator piece at the bottom, but that still doesn't get me into the very bottom where I'm certain there is still glass. Question #1 - Will leaving the glass down there hurt anything? Question #2 - If yes, how do I get the rest of the part off without damaging it? I have a 10+ yr old Model DU920QWDB3 Thank y


The glass should just go down the drain from there. I doubt any piece that made it into there should damage anything as they are would have to be pretty small and as big as any food particle that could fit into there so you should be fine. If you rea ... Whirlpool Dishwashers

We bought an aeg favorit 50674 dishwasher ,last week and yesterday i went to open the door to get the dishes out and the door wouldnt open.i tried again but noticed that it had caught on yhe side panel and was bending the panel.not wanting to make it worse i phoned the comit store that sold me the machine they said it was not their fault and wasnt covered on the warrenty .i still cant get my dishes out cant you help.thanks caz ivey


... AEG Dishwashers

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Maytag MDB 4000 AWB. Not cleaning. not getting water now. pressure was low when i was getting water. . Soap dispenser would not open as well. I replaced the motor on the soap door. cleaned the float switch. Tested continuity and cleaned out water inlet valve. Still not getting any water


... Maytag Dishwashers

The Bosch plastic push button (AP2804452) has broken on my SHU9950 dishwasher. The switch itself is still good. I have removed the broken pieces of the bad button from the unit and am now depressing the switch without the button. When I get the new push button, what is the proper way to remove the control panel cover to put the new button in place? Thanks!


... Dishwashers

I have a triton xl model @ gsd6200g00bb serial #va790400b. The dishes on the top rack are not getting clean. I have removed the top, and middle, and bottom arms cleaned calcium out of them. Removed the screen below the lower arm cleaned. The top and middle arms are still not spinning during wash cycles. Where do I go next?


Apart from the spray arms themselves there could be other reasons why the water is not getting up to the middle and top arms.\015\012\015\012The distribution circuit from the wash pump that feeds the arms could be blocked or the wash pump ... Dishwashers

I've got a hotpoint bf168 dishwasher,been working fine until y'day when nothing washed, realised there was no water coming into it. Change water inlet pipe but still nothing, I can hear water going thru the pipe but then just seems to empty itself. Any ideas guys .


Hmmm.... could be the controler. or a stuck valve... have you tried to reset it? turn off power and turn it back on... ... Hotpoint 23 in. BFI68 Built-in Dishwasher

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

Hi,rn Hi, We are getting an "F4" error appear on our D3350 whenever we try to use it, (wash, rinse, etc). I can see water coming in from the side inlet, but the error seems to appear once it reaches the inlet for the sprayers. Perhaps the sprayer pipe is blocked? Is there anything that we can do to fix this ourselves? Thanks very much, most appreciated


Yes you need to reset dishwasher to time fill.turn off the power button wait 10 sec,push and hold the programme and start buttons then turn power back on.hold buttons down until display lights up then release them.press programe button until 4 shows ... Asko 24 in. D3350 Dishwasher

We used our LG diswasher to clean our grill grates, which was a bad idea, because now the unit will not clean the dishes. We cleared the washer arms of debris, but the unit still is leaving the dishes on both racks dirty and is leaving the liquid soap dispensed into the unit undissolved on the door of the unit. There are no kinks in the water inlet, and water is getting into the unit, but the dishes are not getting cleaned.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please make sure the dishes are loaded properly or\015\012dishwasher is not overloaded. Also check that the dishwasher is filling\015\012properly. It will fill with water up to ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a whirlpool GU2700XTSQ1 dishwasher. I have the typical top rack not cleaning problem. I have removed the rear washer tube that leads to the top sprayer, no clogs. Upper arm is clear, lower arm is clear. I also removed the lower cover, checked the chopper screen and inlet, no clogs. There is a screen inside that I cannot get to. It appears to have some sort of paper or cloth sticking through the screen with a 50% block. Perhaps a sticker or label from a dish. I see this screen when looking


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0849 seconds