Having problems with your Dishwashers ?

Hi Maytag dishwasher, model#MDC4650AWW has power to control board but no responce from any buttons.Finished a cycle & wouldn,t start again.Door switches are okay. Rene


Answers :

Hi
\015\012
\015\012Please check the wiring connections to and from control board, also make sure that the keypad connections are good. Make sure that there is no moisture on control board/keypad. This is an issue with the wiring, use the below wiring diagram and check.
\015\012
\015\012
\015\012daniel_s_25.gif
\015\012
\015\012Hope this helps... Please post back if you need more information.
\015\012Daniel
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi Maytag dishwasher, model#MDC4650AWW has power to control board but no responce from any buttons.Finished a cycle & wouldn,t start again.Door switches are okay. Rene


Hi\015\012\015\012Please check the wiring connections to and from control board, also make sure that the keypad connections are good. Make sure that there is no moisture on control board/keypad. This is an issue with the wiring, use the b ... Dishwashers

Hello. I have a Kitchen Aide KUDG255HWH1 that will not start from a cold state. The "Energy Saver Dry" and "Normal" indicator light/ switches failed to operate about 1 month ago and since then I have needed to use the "High Temp Wash" and Soak & Scrub" cycles to get the unit to run. Now these two indicator kight will illuninate but the unit will not start when I depress the "On" soft switch. When I depress the cancel switch the unit starts with what sounds like a pre-start cycle. Pleas


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. To reset the dishwasher switch\015\012off the dishwasher from the power socket and mains for five minutes and then\015\012switch it back on. If still the issu ... KitchenAid Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

My Lofra LOD6001 dishwasher does not want to start the washing cycle. Water drains okay and fills okay but when the washing cycle is supposed to start nothing happens. Suspecting a problem with the circular pump.


... Dishwashers

I have a KD 12 WW dishwasher. It does not start the cycle when it is switched on. A technitian gave the advise to put 2 litres of water in and start the cycle, but the water is pumped out and nothing else. The dial moves on, but the cycle does not start.


... Kelvinator Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

I bought an ice c1154s dishwasher from carrefour about 2 years ago. I started the e50 degrees cycle and all started okay. It stopped working a few minutes into the cycle and the start light and the b


... Indesit Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

AEG Favorit 350 dishwasher starts cycle okay but starts beeping about half way through and although dishes appear clean there is dirty water lying at bottom of dishwasher so not draining away and the drying cycle has not started.


... AEG 23 in. Favorit 88070IM Built-in Dishwasher

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene


... Kenmore Dishwashers

Bosch SMU 2000 (2042-600). Will not start wash cycle. Can hear very faint clicking sounds with ear next to control switches, but motor does not start, etc. Tried various switch combinations (pots/pans, etc.), but does not make any difference.


... Bosch Dishwashers

I am trying to fault find a Hobart AM15 ML-130038 dishwasher. Wash cycle does not start automatically after the water level activates the level switch & energizes the contactor? To get the wash cycle to start you need to open and close the door.


... Dishwashers

After the initial drain cycle when the first rinse cycle starts the water flows up out of the air vent hole at the top of the water manifold and fills the overflow tray in the bottom of the machine causing engaging the micro switch starting the drain pump which then stays on continually.


... Bosch SHE4AM02UC 24 in. Built-in Dishwasher

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Bauknecht GSX 4756w when I switch it on and set the dial to the wash setting, I close the door and it sounds as though it is about to start but after 30 secs just starts beeping. When I open it the cycle setting is always reset to rinse. Can't get it to switch on at all.


My dishwasher will not start: Most common d/w power is 120 volts, check for 120 volts with a ... Bauknecht Dishwashers

Have a Whirlpool Dishwasher 6ADP 5540. Starts cycle - fills water then about a minute into it the start buttons flashes 6 times and will not continue on. Very rarely, the cycle does continue on. Have turned off at the main switch. But still have this problem. Look forward to your reply. Cheers, Jodie


Hi Jodie,\015\012\015\012An F6 fault code - indicated by the green light flashing in sequence next to the start button - is indicative of a water inlet problem. \015\012\015\012First of all check that the water tap the dishwah ... Whirlpool 24 in. ADP6940 Dishwasher

I have a ASKO Dishwasher DW 1875 F2 appeared and so switched it of. Now the machine starts in a cycle where the element heats and it won't switch off when I press start stop butten


... Asko 24 in. D3350 Dishwasher

Our dishwasher model is a Nautilus FP920WW. The unit switches on OK and displays the normal wash cycle settings but when we try to start or change a cycle (or press any button for that matter) all we get is a quick, intermittent beeping and nothing happens/changes. Switching the dishwasher off and on again at the wall does nothing to solve this problem. What's going on???


... Fisher and Paykel Dishwashers

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1756 seconds