Having problems with your Dishwashers ?

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Answers :

Hi There,
\015\012
\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lever, there is evidently no problem with the drain pump.
\015\012
\015\012The information you provided, while detailed, is slightly unclear. It would assist me greatly in diagnosing the fault if you could answer the following questions based on a regular wash cycle:
\015\012
\015\0121. If you open the door about 10 minutes into the wash cycle, is the water in the bottom of the washer hot - or at least warm?
\015\0122. How long is left on the timer when the machine "dies" and will go no further?
\015\0123. Is it warm/hot inside the washer when it "dies"
\015\012
\015\012Please let me know the answers to these questions and I will then be able to assist you further.
\015\012
\015\012Regards,
\015\012BElectric
\015\012
\015\012
\015\012
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

I have an Asko w66 front load washing machine that will only wash one way with a 60 second time delay and washes the same way again instead of reversing. At no time will it wash the other way. At the first spin cycle the water is pumped out but the wash drum will not spin. The pump continues to pump and will not stop while the one way wash continues. The timer stops at this point with the one way wash and pump still pumping continuously.


... Asko Dishwashers

FDW60 dishwasher Hi My dishwasher is about 15 months old and the problem I have is that it seems to stay on pump and the Ecco45 light is flashing.  A repair company looked at the machine and said that the motor looked like it was leaking and water was getting in the bottom setting off the micro-switch.  He contacted Hotpoint who fitted a new motor today at a cost of £89.85.  Went to use dishwasher tonight and we still have the same problem.  The dishwasher started the washing programme for about


I've just (as of 10 minutes ago) had the same problem. I followed the advice given elsewhere in this forum and removed the bottom cover - water running out so needed a big towel to mop it up. I stood the machine upright and restarted it - no problem! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My dishwasher siemens se25a266gb purchased in 2003 will fill with water go through a wash cycle but does not pump out the water i have cleaned out the filters, checked the exit hose and all seems ok the only way to get the water out is bale out by hand. after this it will run through a wash cycle then stop and not pump out. how would i get to the pump and check it? any help appreicated regards Alan


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

I have a Hotpoint Aquarius FDW 20 dishwasher. Prewash and Wash lights were flashing, machine had stopped and water was at the bottom of the machine. What does this indicate? After removing some debris from the water drainage pump, then reassembling the machine, I now get the pre-wash LED flashing and a motor operating, but no futher progress into the wash cycle. What does this mean?


Dishwasher always full of water at the end of cycle ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hi, I get a problem reading " E4". I have now switched the machine off and on again, but still it says the same. Incidentally the machine has already pumped the water out, so the 'overfill" is actually not supposed to be a problem. It is KELVINATOR EXTREME CLEAN DISHWASHER, model KD14SS. Please help, how am I to get rid of this problem, I really do not have the time nor the money to get outside help! Anita Kleynhans


... Kelvinator MDP531RF Dishwasher

My LG dishwasher upper rack has stopped cleaning. The uppermost arm is seemingly getting no water at all and the arm on the underside of the upper rack is getting some water, but not enough to turn it. I have already disassembled and cleaned all the way down to the diverter assembly and it has not fixed the problem. I think this is a problem with a the (?) diverter pump or perhaps a sensor that sends water to the upper arms. I am trying to figure out how to further diagnose the problems. The


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDF6810 Built-in Dishwasher

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

Hi! My bosch SHE43 built in dishwasher is about 2.5 yrs old, dishes aren't getting clean anymore. We have *really* hard water so I use the max rinse agent, but doesn't help. I clean the little canister filter with each wash, and just washed off that grate in the bottom. I also just cleaned the trap under the sink, but it didn't look bad at all. The problem is a grit left on glasses and things just not getting all the way clean. When I remove the grate at the bottom, there's a bit of water


Hello. Let's begin by tossing two cups of vinegar into the empty dishwasher and running it on it's hottest and longest cycle. Always run the hot water in the sink faucet until it is as hot as it gets before starting up the machine. Let that cycle ... Bosch SHE43C02UC Dishwasher

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America


Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers

Ref: NEFF Dishwasher S5555XOGB/70 (FD No. 8602) Problem: Does not drain at end of wash cycle. Checks/Symptoms: 1. No blockage in whole of drainage system, system and filters are clean. 2. Pump does operate mid wash cycle ? drainage tube can be felt pulsing and pipe gets warm right through to the main drain connection at the ?U? bend. 3. At end of wash cycle the pump appears to still be trying to run but there is no flow, even when the door is opened. If machine is emptied by hand the pum


... Dishwashers

Washing machine I have a Kitchen Aid washing machine that has a problem with the agitator,normally it rotates left and right, now it only turns 1 way causing the clothes to get wrapped up. If any one can help, that would be great . Thanks Glenn.


Well, I guess by the sounds it you guys have belt problem.\015\012Check to see if the belt is not slipping, if is you may have to tighten the belt. it is very simple there are two bolts on the motor,\015\012One has a slot, and one is just ... GE 15" Laundry Pedestal for Horizontal Axis Washers and Dryers - White-on-White

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

I have a Hinari lifestyle HDW 43SL dishwasher. Power is getting to motor (can hear buzzing), it sounds like water is getting to machine but it doesn't work could there be a problem with the pump for the waste water?


... Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

Last couple of days bottom rack of dishwasher not been clean on 65o wash, having emptied and run the machine empty etc it seems that whilst there is water being pumped through the roof mounted vents and to the "spinner" attached to the upper tray, the spinner attached to the base of the machine is not getting a) any / b) sufficent water pressure to make it spin...im guessing the feed is blocked?


... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

The dishes have food residue washed onto them and water spots on all glasses regardless of the amount of detergentinse agent. The pump seems fine there is no water left in the machine after a cycle. any suggestions other than getting a new machine? thank you!


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... Bosch 24 in. SHU43 Built-in Dishwasher

Too hot Water not circulating during wash cycle. Machine will pump out and allows water in. Machine gets very hot if left on - does not switch off automatically. Programmer revolves freely.


Replace bad control board ... Indesit 24 in. D63 Free-standing Dishwasher

Dishwasher is 16 months old. Recently, it won't get tea stains from spoons or cups and there is a white film on plastics. I have run unit once with vinegar. I tried using less detergent and no change (Cascade Complete). (Neighbors using same detergnet on different machine with no problems so it's not the water.) I always select High water temp and air dry on normanl wash. My hunch is that the motor is going bad and therefore it is not pushing the water with enough force.


Hello, there are a few thinks to check on the dishwasher. Circulation, drainage - no backflow back into tub, and water temp. If all three are good, then you have hard water. \015\0121. circulation - These MDB models are very good with water circul ... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1528 seconds