Having problems with your Dishwashers ?

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


Answers :

You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutral..the customer had lost a neutral leg to the circuit... if you indeed have the correct voltage the power goes through the door switch make sure it is latching and sending current back through the circuit board... not positive but does this unit have a fusible link on the top part of the circuit board. dome of kitchen aid and whirlpool gray boards installed a fuse that would go bad also...hope this helps out if not repost with more info we will get you running somehow.... good luck
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.


Hi\015\012\015\012The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the do ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug, GFI and circuit breaker switch. Still no power and no light no response from various buttons.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012It sounds like you've got a bad power switch or a wire at the power switch or as you described it... (circle with a I, looks like a reset button?) ... Asko 24 in. D3530FI Built-in Dishwasher

I have a KitchenAid Dishwasher KUDIO1iLBS2 and none of the lights come on and if I press any of the buttons nothing happens. The unit is getting power to it as I shocked myself. I did ordered and replaced the control board and still nothing is happening. Any suggestions or ideas? Is there a reset button or is there a possible fuse that is out that would make the lights not come on? Please help.


... KitchenAid Dishwashers

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Bosch DW model SHU53A05UC/17 was working fine until yesterday evening. Went to turn it on and now get nothing. No lights, no power zip. It's on its own 20amp circuit. Checked the fuse and it's not blown. Flip the breaker on/off a few times anyway to make sure. I was installing a floor and used my miter saw on the sump pump circuit (diff from the DW circuit). It blew the fuse a few times. Any chance, on a diff circuit, it spiked and damaged a board in the DW? What part (part #) would


... Dishwashers

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

I have a Bosch SHU 3030 dishwasher that made a loud clicking noise and then stopped mid cycle. There was water at the bottom of the washer that I scooped out. I checked the filter and cleaned out any debris. There appears to be no power to the dishwasher. I spin the control dial and nothing happens; no lights, no sounds. The circuit was not flipped.


Pull the bottom kick panel and check the connections on the lower right, where the electric wires come in. Trip the breaker first, to be safe. ... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

The power is going to the dishwasher. The on off buttons work. No error codes. The salt light is lite (has been for 5 years) but now I get zero response when shutting the door (after selecting any of the 6 run options). There is no noise, no water, nothing happens. How do I repair this dishwasher so that it will run again?


Door switch failure. This will shut down all other start options. Inspect and possible replacement. See if you can activate it with something with door open. Give it a good close look... ... Dishwashers

I have a kitchenaid dishwasher mod KUDK01TKBL1. It was running fine, opened the door and now the unit is dead,no lights nothing. It has 119 volts to it, the circuit board has line voltage and the door switch seems okay. I could not find any thermal fuse in this unit


... KitchenAid Dishwashers

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

Maytag MDB6600AWW Unit is approx 3 years old it was finishing a load and stopped part way through sticking on heated dry. I don't know if it was there in the cycle or if the diagnostics on the board sent the message there. The light now will not shut off or move from the heated dry. I have disconnected 120 volts, removed the panel to check wiring, removed board and reassembled nothing resets the heated dry light and nothing works. I have gone through manual function test, sales floor demo test,


Have you tried pushing heated wash, heated dry, heated wash then heated dry? Sometimes this will reset it. ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain button still nothing happened. I close the door tight..nothing. I check the trays if there something stuck inside..nothing. I unplug/replug the power cord nothing? my wife was using it when this got stuck about 3 weeks ago.


Did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck ... Whirlpool GU2400XTP Built-in Dishwasher

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 ... Amana Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Gibson Furnace Hi and thanks for reading my question. I have a Gibson furnace with electronic ignition. When I turn on the power to the furnace it starts running with the batteries removed from the thermostat. It blows but does not produce cool or or stop running. The circuit board has a small red light that is flashing but does not seem to have a pattern. I would appreciate any input that you may have. Also are the relays located ont he circuit board itself?


... Dishwashers

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1462 seconds