Having problems with your Dishwashers ?

The display light is on "locked" How do I get it unlocked?


Answers :

Press the stop/pause button then the washer will unlock automatically, if it fails to, please unplug the cable from the wall.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The display light is on "locked" How do I get it unlocked?


Press the stop/pause button then the washer will unlock automatically, if it fails to, please unplug the cable from the wall. ... Dishwashers

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Maytag dishwasher mdb7601aww program not working right. Lights on display not lighting. Push button and it reads 2 hour delay. Cannot get it to run without delay. Thanks, Bill


... Maytag Dishwashers

Hi, I have the Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 .. aged about 6 years old .... When I press the on/off button 'on' the led display only shows the 'not started' message. When I press the on/off button 'off' the led display lights up momentarily with 'start' etc just before I have fully released the button. I have tried a new switch and the same happens so not that. ALSO i can sometimes see S1....> on the top panel and get the machine to show on the top panel the close door


... Dishwashers

Kenmore dishwasher model 66517373300 lock light is on and can't unlock the computer board to start wash. How can I get it to unlock?


... Kenmore Dishwashers

Fault PP It pumps and pumps with a gradual flow of incoming water but doesn't get anywhere. The top display reads 188 with salt and the other warning light on (sorry, I only know the danish word - afspaendingsmiddel), the front display reads iPP (the i is raised).


A leak which has activated the flood safety in the base, you can check this by pulling the machine onto a towel and tipping the whole unit forward ie raise the back of the machine off the floor so it is pivoted on the front feet at approx 45 ... Bosch Dishwashers

I have a PLD3460RDC1 dishwasher.The power got shut off and it now displays an ER message with all the other lights blinking.I have shut off the power to the unit many times, first getting a PF error and then it goes to the ER with all lights blinking. How can I reset this?


HI, there has been a power surge/pulse, that has been absorbed by the electronic control board. There may be serious damaged here, in this case. You can try to reset the main logic chips by unplugging, or shutting power down for five minutes. If the ... Frigidaire Dishwashers

I have a Fisher and Paykel DW60CDX1 dishwasher, the display originally came up eith an error code for the door, which seemed to be the problem as it restarted with some pressure on the door, then it stopped again and now there is no LCD display and no action, cycle butten lights are on but will not make a noise when pressed. We live in the bush and cannot get a easy service option. Is there a diagnostics mode I can try, although the LCD may not work?


Old question, but for anyone else, hears the answer - http://www.recalls.gov.au/content/index.phtml/itemId/1015047This model has a product recall, minehas done the same as described above, recall issued Aug 2012. ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

My whirlpool quiet partner 2 has the light on under the lock but we can' t get it to unlock so we can run it. How do we unlock it?


I need the model number too! They do make a few, you know. ... Whirlpool Dishwashers

My lock light is on and I can't "unlock" it. How do I get the lock off, so I can wash dishes.


Press the lock button for 3 seconds. find a lock icon on panel ... Whirlpool GU2400XTP Built-in Dishwasher

I am having problems getting dishwasher to restart after I interrupted a cycle. I have done the cancel cycle pressing Normal and Delicate together. The dishwasher emptied then showed a PF signal. Now is it showing a LE signal and all Front display lights are flashing.


You should be able to reset it by tripping the breaker and waiting about 10 minutes. Then reset the breaker. Best regards, --W/D-- ... LG LDF8812 Stainless Steel Built-in Dishwasher

I got the pressure washer started - lots of smoke etc after not having used 3 years. I then poured in wrong oil to top it off - my brother's chain saw bar oil. DARN. After 3-4 minutes it started rattling and stopped. Can't pull the chord to get started. Did it seize the engine? I have drained all oil. Can I try using a cleaner, light weight oil to try to unlock it?


Nope! you have blown the seals and most likely the cylinder is full of water. You will need to take it to the repairer to have it cleaned checked and new seals fitted. $200 ... Karcher 1750 psi Electric Pressure Washer

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a kenmore dishwasher model # 16872000 and yesterday the Lock on light came on and will not go off. It will not let me start the dishwasher. How do I get it to unlock?


... Kenmore Dishwashers

I have a Kenmore dishwasher, and when we shut the door, without starting a ccyle or anything, the motor will start going!! When we do start a cycle, it will get stuck at some point during the cycle and won't sanitize or show the "clean" display light as being lit.


... Kenmore Dishwashers

I managed to 'lock' the control panel on my maytag dishwasher and i can't get anything to operate. The lights just keep flashing at me. What or where can i find the unlock code?


Hello. No problem. Press the START/STOP button to stop the machine. Then check your watch as it takes up to two minutes to unlock the door. Next pull the door indentation opposite the hinges. \015\012\015\012If the door still won't open, c ... Dishwashers

How do you unlock the locked button on your dishwasher? the locked light is on. can't get it to work.


The solution is very simple.Just press and hold "heated dry" option for five seconds. ... Kenmore Dishwashers

My Fisher Paykel dw60cdw2 dishwasher stopped working mid cycle and I cant get it started again even aftre switching power off and pressing reset.. All lights on the console are working except the number display on the left side. What is the problem likely to be


Had the same problem and it was the microswitch that is behind the door skin which is associated with the lock mechanism. got a new one and away she went ... Fisher and Paykel Dishwashers

No power My dishwasher Model DMR77 quit working yesterday during a wash cycle. No power ie, no display light or tones. I am getting power to the unit, checked with a volt meter. I am thinking Power supply, or is there a reset on the unit.


Hi,\015\012 The main PSU is part of the control board. You may be lucky to find an aged fuse to replace, but it's more likely a power transistor that's fried.\015\012\015\012Unplug and remove the control board to see which bit's toa ... Samsung DMR77LHS Tall Tub Dishwasher

We have a Frigidaire Gallery Series dishwasher we just purchased in August. Model #GLD2445RFB2. We are experiencing a problem with it. We noticed it started running louder then normal and now it will not finish a wash cycle. It gets half way through and PF lights up on the display and the cycle never finishes. It doesn't matter which cycle we choose it has done it on all of them.


... Frigidaire Dishwashers

Not sure if this is the correct model # but I get an F on the light panel that usually displays the time- I know it is not a plumbing issue any other ideas


... Gaggenau GI 230/161 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1020 seconds