Having problems with your Dishwashers ?

I have recently changed my dishwasher over from a direct hot water pipe into the dish washer, to a cold water pipe but the temperature lights keep flashing and then the cycle, which has barely begun, stops. wat to do?


Answers :

A dishwasher requires a hot water line to operate properly. The dishwasher is indicating the water is too cold to even begin a cycle.
\015\012
\015\012Charlie
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have recently changed my dishwasher over from a direct hot water pipe into the dish washer, to a cold water pipe but the temperature lights keep flashing and then the cycle, which has barely begun, stops. wat to do?


A dishwasher requires a hot water line to operate properly. The dishwasher is indicating the water is too cold to even begin a cycle.\015\012\015\012Charlie ... Dishwashers

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

Hi. IKEA Whirlpool DWFA10 dishwasher.Firstly, when switching on the machine to befin the programme the machine does not pump residual water away.It then begins its cycle (in this case the pre-rinse cycle).After 12 or so minutes,when the cycle finishes and the water should be pumped away,the machine stops and the green warning light keeps flashing 4 times intermitantly.


... Dishwashers

We have a problem with our Miele G851 SC Plus dishwasher. We have not operated it for over three months as we were away on vacation and also because there were other issues in the kitchen due to some water flooding . Yesterday we switched on the machine and notice that the machine flashes the intake / drain light after a few minutes into the cycle and stops working. we have checked the drain pipe for blockages and also the water pressure is good. I disconnected the machine drain from the


Www.miele.ca/miele/canada/OperatingInstructions/.../G851%2005431311.pdf\015\012\015\012\015\012\015\012 ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Flashing light The 3rd light to the right keeps flashing. I cannot cancel the programme or move the indicator light to any other setting. When I close the door the machine does not come on, just the light keeps flashing. Any idea what the problem can be? There is no water in the machine and doesnt appear to be any blockage in the outlet pipe.


... Smeg 24 in. DWI612 Built-in Dishwasher

I just bought a kenmore elite model # 13193 hooked it up ran it and it stopped mid cycle the detergent was released but not dissolved and the clean light keeps flashing. Ive reset it and turn up the water heater temp but still does the same thing.


You need to hand prime all new installs with a gallon of water first,Put it in then run cycle. ... Dishwashers

My hotpoint dishwasher keeps going off it starts the cycle and you can hear water coming through but after about a minute or two it stops and the second and fourth lights flash all the time does anyone know why?


I am assuming you have tried the possibility it is the water inlet circuit which could be faulty.\015\012\015\012Check page 13 of the ... Hotpoint 23 in. BFI62 Built-in Dishwasher

Diplomat dishwasher ADP8112 - stopped mid cycle, full of water, no lights on. Thought on/off switch faulty so fitted a new on. Now when you switch it on, lights 4 and 5 flash, then there's a beep and then flashing lights stop and lights 3 and 5 come on and stay on. Any ideas as to how to fix, please?


... Dishwashers

I have a modulogic ADP951.seemed to be stuck on cycle today so I stopped it. water did not drain. I cleaned all rotors and filters and re started. Water drained however start light now flashing. Have tried holding for 5 secconds to re start but only starts pumping out water (of which there is none) and then stops. Light continues to blink. Any other tricks??


I am assuming you have not tried the reset by turning mains power off and then on.\015\012\015\012One of the reasons for being stuck in the wash cycle is the water temperature is not reaching the right level. This could be due to heater ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

FDW40 My dishwasher has just stopped working mid cycle. The rinse and prewash lights are both flashing and the water will not drain away. I tried to empty the existing water out........put it onto a new cycle.......the water came in but again wouldnt empty.... Please advise


This is a blocked pump,Strip down pump and remove blockage. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher

It won't complete a full wash cycle keeps stopping part way through and low rinse aid, low salt lights flashing even though both are full ??? Pamphlet says this might also mean there is a kink in the inlet hose but that seems fine as well. Have had the dishwasher 3 weeks and it has completed about 4 cycles without stopping ???


Check water valve to see if it has something blocking water supply ... Dishwashers

Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit the start butt


... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher

Dishwasher cycle starts briefly for a couple of minutes and then stops again and the standard wash and eco wash programme lights are then flashing together? It appears that water is drawn into the appliance for a short time and it then seems to start and empty itself before the above lights start to flash, all within 3-4 minutes?


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Stops mid cycle often Our westinghouse 905 dishwasher often stops at the rinse part of cycle, flashing lights, water sitting in base of ...


... Westinghouse Dishwashers

I have an Ariston LI45. The stupid thin one. It's not seen much work & is just out of Guarantee. It's stopped working & is showing 2 flashing lights. Stops partway in to a cycle with water in the base, but not enough to cover the element. Tried re-setting, no difference. I have also noticed that it's melted a plastic wheel off the bottom tray at the back. After reading problems with other washers, i'm guessing the water level switch & maybe element too. If this is the case, i'm ok finding the


... Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

My Whirlpool ADP6565 dishwasher stops before the rinse cycle. The start button then flashes and the rinse light on the cycle selelector knob is lit up. if I hold the start button in the water pumps out and then stops. I have to manualy set it to rinse to rinse the dishes.


You may have a blocked faulty, pressure sensor, or the hose is not flowing freely? Check that out.\015\012\015\012Below please find a service and repair manual, if you use the troubleshooting steps you maybe able to isolate your issue, and affe ... Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Green light flashing and water still in bottom of dishwasher. I have cleaned the filters also I cannot reset the start button it just keeps starting again and then stops and green light flashes again


Hi,If this is the clean light the follow the link below, it will explain the flashing and how to reset the control so you can use the dishwasher again. ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2132 seconds