Having problems with your Dishwashers ?

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

Have SHU43C and have had no problems with it. We usually run it on the Quick Wash cycle, but ran it on the Regular Wash cycle yesterday because the glasses seemed to be coming out spotty. After it ran, there were no lights on the display like there usually are. The washer had run and the dishes were clean, but it has not drained completely. There is still about an inch of water in the bottom, despite removing and checking both the Large Object Trap and Fine Filter (neither which were clogged


The drain pump needs to be replaced or cleared of obstruction. ... Bosch 24 in. SHU43 Built-in Dishwasher

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

Miele Model G 692 SCI PLUS does not start up. It drains water if you put water in the bottom. The Inlet/Drain light flashes. I have checked all the water filters and cleaned any very small particles from them.


The inlet/drain light also comes on when there is water in the base pan. There is a float switch that triggers this and over time if water has collected in the base pan the float switch can stick. Pull out the dishwasher and tilt it towards to back ... Dishwashers

Dishwasher ZTD 5052 : small amount of water won't drain away so I keep getting warning (flashing light on quick wash) it's only a cm or so deep at bottom of dishwasher, cleaned filter etc. still no luck. Sink is not blocked. Thanks


... Zanussi 18 in. ZDT5052 Slim-Line Built-in Dishwasher

Hi i hace a haier dishwasher dw12 pfe2u ive plumbed it all lights come on wen try to put wash on it just flashes and beeps. when filling my salt container up its all cum out bottom of dishwasher . dishwasher isnt filling up wiv water all pipes have been checked


... Dishwashers

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Check water light stays on rendering machine unuasable.checked water supply.all filters .googled problem told me to switch water supply on and off rectified problem for 10 minutes then check water light came back on. water remains in bottom of appliance.


... Bosch Dishwashers

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Asko 1996 appears "dead".....no lights flashing, won't respond to repeatedly pushing on/off button. Some water left in the bottom...siphoned it out, cleaned filters, no blockage there. Almost like it's not getting electricity, but breaker is on. Noticed this when I went to empty clean dishes, and noticed that detergent hadn't dissolved and dishes weren't clean and about a gallon of water was still in the bottom.....


Don't know if this will help, but my dishwasher has a "propeller" device above the top and bottom racks that spins while dispensing the water. If the dishes on either rack are stacked too high (i.e. if even one plate comes in contact with that ... Asko D1996SS Built-in Dishwasher

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

I have BOSH Semi integrated dishwasher SGi4305AU/12 which went in a strange dead cycle. Any operations I will choose it just try to **** water in to the drain. Also I think that it is important that now on numerical display shown a red dot at the right bottom cornet of it which has not been seen before. I check filter area for debris and it is clean. I checked drain pipe and it is clean too. Moreover I look inside with the open door during operation and what it does that small amount of water


I would suggest downloading a user manual for your dishwasher form this site. Click on service link and then go to the instructions ... Dishwashers

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Fisher & Paykel DW60. Fault: Will not start regardless of program selected. E.g. if "heavy duty" pressed, only light will flash, if "normal" is pressed, only this light will flash etc. All hoses (water and drain) have been checked and no crimps or blockages found at either end. All usual methods tried (e.g. cleaning strainers and filters, turning power off for a while etc). Finally, while lights are working, the machine makes no noise at all when a pogram is selected.


... Dishwashers

Dishlex Global 310 model. My dishwasher has water sitting on the bottom of it and it wont drain. I noticed it after I did a cycle of dirty dishes and the 'fast' light was flashing when I went to open it. Which shouldnt have been because it was on a normal wash. The water has been sitting at the bottom for 2 days now and still wont drain! I've taken out all the parts on the bottom which come out and cleaned them. Still no change however.


Just ran another cycle and it was fine ... Dishwashers

Intake/Drain light is on. First flashed F13. Cleaned the water intake filter;cleaned the triple filter and drain pump.Light continues to stay on-it seems as if no water in coming in the dishwasher. Water supply is on all the way.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. F13 is a\015\012flow meter error; unfortunately there is no way to reset it so you’ll have to\015\012get ... Miele Dishwashers

I have a Hoover dishwashe HND 6515. I put it on the universal 65c programme this afternoon and sfter 5 mins it started a continual beep beep beep noise and the red light on the universal button was flashing, I then notices it was emtying water all over the kitchen floor, seeming to come from under the bottom of the door. I turned it off and when it finished pouring out water opened it up and the bottom of it is full of water which will not drain away. I have checked the filters and they are all


... Hoover Dishwashers

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

We've got an Meile Incognito dishwasher, model G 843 SCVi plus. It purges at the begining of the cycle and then seems to fill with water, but then the red Intake/Drain light starts to flash and the cycle goes no further. I've removed, checked, cleaned and replaced the triple filter and the drain pump but the light is still flashing. I spun the propeller both ways, no problem there. Any ideas for me?


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

My Dishlex global 300's rinse light is flashing after 5 mins use. About 2 inches of water stays at the bottom of the washer. Bought this second hand and it has not been used for a few months. Do I need to fill the reservoir under the washer or lean it at 45 degrees to dislodge anything in the sump. If you have had the problem of the washer starting its program and then stopping after 5 minutes and the rinse light flashing I would appreciate your advice. Cheers Hyph


The flashing rinse light is an error code. I am assuming that your control board is good because the lights are working. I'm also assuming that this model has two pumps. One for filling and one for draining. The rinse light flashing is probably i ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1949 seconds