Having problems with your Dishwashers ?

LG LD-2120WHU dishwasher take in water like normal, wait a fewe seconds and then pump it out again showing the error message E1 on the display?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

LG LD-2120WHU dishwasher take in water like normal, wait a fewe seconds and then pump it out again showing the error message E1 on the display?


... Dishwashers

My Miele Dishwasher (Excella Series G 2630 SCi) fails to fill. I get the message "Water inlet - Open the stopcock". I checked the water inlet filter and looked for hose kinks to no avail. I even checked the non-return valve. When I start the dishwasher I can hear a low hum (Not the pump) for a few second before the error message displays.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Hi . I have a Zanussi DE6965 which has started displaying the error message AL6 every now and then. When it stops and shows this the water has not pumped out. If you turn it off, leave for half an hour or so and turn back on it sometimes works fine to the end. Sometimes it stops again. Eventually after several stop starts it works through. Any advice what could be causing this? Thanks.


... Zanussi 24 in. DE6965 Built-in Dishwasher

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Dishlex global 450 _ how do i fix fill level time fault? displaying oF? Hi There, I have the above dishwasher and saw your advice on fixing fill levels - my display is showing the oF message and the pump to drain remains on whilst mains is connected. turning off mains does not clear message. holding eco button down does not clear message? is there anything else i should do in terms of removing parts to assist the process? I have cleaned out all of the drainage bowl and all is clear. i would pref


... Dishwashers

Error Code E1 means longer inlet time. possible causes faucet is not opened, or water intake is restricted, or water pressure is too low, according to the BRADA portable dishwasher model EP9242AWW What does that mean and how do I fix it? I have shut the water faucet off and the error message still shows.


... Dishwashers

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

I have An LG LD-14ATI Dishwasher, it starts, pumps water in, shows up with E1 in display and pumps water out. Can you please help and tell me what is wrong and why it is doing it. thank you


Hi there,\012Well It is probably Faulty Water Inlet ValveFaulty Water Inlet ValveThe water inlet valve is the device that meters water from the supply lines into your wash tub. On domestic washers, there are two lin ... LG Dishwashers

Our 2 drawer Fisher and Paykel dishwasher is automatically starting its own washing cycle (well, motor starts, but no water appears to be entering), then it shows F1 error message and a spanner icon flashes. Within 30 secs of this occurring on one drawer, this starts on the other drawer. Only way to stop is to switch off at power socket. Any idea what the error message is telling me?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Our Asko D1796 dishwasher has all lights flashing and is displaying a F2 message, which according to the good book means there is too much water in the machine. I have followed the instructions for a normal inlet time but the indicators will not change. Is it trying to tell me the Drain Pump is dead? A new drain pump was fitted three years ago. There is no eidence of water in the machine. Can anyone help? Thanks. Alan


Hi Alan,\015\012\015\012The F2 on Asko means it's sensed an overfill, that in itself though can be provoked by a couple of thing's. First, check for blockage at the end of the drain hose where it connect's to your household plumbing, be it under the ... Asko D1796FI Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

I have a DD601 v2, the bottom draw starts up and pumps water in then pumps it out again immediately. No error codes are showing, it just shows the cycle time remaining but doesn't decrease from its start time.


I am assuming the drawer is showing this behaviour repeatedly even after your start fresh with power turned off and back on.\015\012\015\012Are you able to see any different behaviour with the shorter cycles in ECO mode?\015\012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have a ASKO D3432 The pump starts when the cycle starts, empties out all water, fills with water and then stops. Error message is Water Inlet Fault. ???? But the water is filling and there is no crimps etc on the water supply line. Save me.


... Asko D3432XLSS Stainless Steel Dishwasher

Error code OE; dishwasher stops with error message 2 min into cycle, drainage seems OK, water doesn't appear to pump into machine - any advice?


Hi,The most common cause of an OE error code on a modern LG dishwasher is: 1. Blocked drain hose 2. Obstruction in the sump area (beneath the filter, which needs to be removed to check for onstruction) 3. Failing drain motor.& ... LG 24 in. LD-12BW5 Free-standing Dishwasher

I have a Bosch Dishwasher Model # SHU43C that is not washing properly. Some dishes are not being cleaned if we don't pre-scrub or rinse. There are no error codes on the panel. During the cycle I hear the pump motor starting and stopping repeatedly on about 1 second intervals. I suspect it may be starved for inlet water. I checked the inlet water line and it is clear. We use well water that occassionally has some iron sediment in it and it plugged the inlet water screen for our washing mach


Hi,\015\012It is very possible that the screen is plugged...most inlet valves have a screen just like your washer does. I would at least remove the hose/pipe and check the flow...and check for a screen. \015\012Also the solenoid can get j ... Bosch 24 in. SHU43 Built-in Dishwasher

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

My lxi dishwasher drains more water than it fills during a cycle so after about three cycles the water level becomes to low. No error messages come up but I have to turn it off and refill it all the time. water pressure at the machine guages shows about 20psi when rinsing


There are two different styles of lxis one style has a drain diverter valve probably messed up some how something stuck in it not diverting the water to the wash arms and instead pumping right down the drain I am guessing this is your problem.There i ... Hobart 24 in. LXIH-3 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1761 seconds