Having problems with your Dishwashers ?

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Answers :

Hello &\015\012Welcome to FixYa
\015\012\015\012

Check this\015\012diagram....first check part#308 flood switch as if that is bad these kind of\015\012issues occur....after you have checked that and it is fine then the control board\015\012needs replacement. Yes you are right 41 seconds can be correct time of your\015\012unit. Please get back to me if you have any other questions.
\015\012\015\012

Kevin

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

Whirlpool dishwasher model DUB700XB has quit cycling. Fills with water but will not start wash cycle. Making intermittent humming noise unless the door is open to disengage the switch, even when on stop. No LEDs lighting when rotating the dial through the various cycles. Unit is old and wondering if it's better to buy a new one rather than fix this and have something else go wrong in the not to distant future. Thanks in advance


... Dishwashers

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

Model #665.15782 The dishwasher will fill up and performs normal, but when it starts the wash cycle, the cycle only washes 3 to 5 seconds, and then begans to go to the next cycle, the problem it only washes 3 to 5 seconds, what can I do to fix it?


... Kenmore Dishwashers

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

SHE45M05UC I installed this model Bosch dishwasher today and it will not start up and run through a cycle. It does not fill with water and start washing. I can hear the unit attempt to start but after a few moments everything goes quiet and that is it. Thanks, Tom


The problem is the float switch is stuck ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Electrolux Dishwasher Model EIDW6105GB1... no error codes...I select the cycle, everthing appears normal...start to hear water fill, but doesn't progress to point of opening soap container. When I open the door all lights are blinking. I've canceled and tried various cycles, but with same result... all lights are blinking. Even tried just a rinse only. all lights still blinking.... This unit is only 4 years old!


... Electrolux Dishwashers

My Kenmore 16533 dishwasher all of sudden started running really loud on the wash cycle. I stopped the cycle, drained the unit, and looked for something obstructing--found nothing. Started it up, and the problem persists. The dishes do come out clean, however. The dishwasher is 6 yrs old. Is this a problem I could fix, or do I need a repairman? Is it worth the expense of a repairman, or is it time for a new unit?


... Kenmore 24 in. 16533 Stainless Steel Built-in Dishwasher

Whirlpool Dishwasher Model ADG 7560 Unit is only 2 weeks old. Program cycle starts, runs for approx 30 seconds then stops. This is an intermittent fault, sometimes it works OK


Found outlet pipe was kinked, stopping water flow ... Whirlpool Dishwashers

The dishwasher fills, heats and starts washing... The washing cycle lasts for about 5 seconds then stops,, then restarts,, this occurs about 4 times then the unit shuts down and all lights go off..


... Amana 24 in. ADB3500AW Built-in Dishwasher

I have a kitchenaid dishwasher model kudio1tjwho. It filled and stopped working. I can not cancel or change the cycle. I press start and it washes for about 30 seconds and shuts off. All the other buttons flash when pressed.


... KitchenAid Dishwashers

New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

Washes for 5 seconds then stops, then starts again intermittently First the heating element started to turn on during the cycle. I never used it before. I changed the setting to unselect Hi Temp Wash but don't remember if it was selected before. The next day the dishwasher filled as usual, washing started for about 4 seconds, then stopped for aroud 10 seconds. The start/stop cycle repeated about 4 times, then all lights went off and nothing more happened.


Bought a new dishwasher... ... Maytag 24 in. MDB7650AW Built-in Dishwasher

Diagnostic dishwasher stops shortly after starting a cycle. I start a cycle, it runs water into unit, starts to wash. After 5 seconds it stops, 10 seconds later it starts again, repeats 2 more times, then all lights on panel go out. any help would be greatly appreciated.


... Samsung 24 in. DB5710DT Stainless Steel Built-in Dishwasher

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit the start butt


... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

My GSD3600 GE Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit


Hello Greg,\015\012\015\012Your diagnosis is pretty good, but the buzzing suggests it may be the capacitor for the pump motor that has failed rather than the pump motor itself. The capacitor phase-shifts the AC current for starting the mo ... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2662 seconds