Having problems with your Dishwashers ?

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


Answers :

I think I just responded to this problem. Please accept both if you are happy with the solution.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. Thanks


... Whirlpool 24 in. GU3600XTRY Stainless Steel Built-in Dishwasher

Lock Control I don't have a manual for my dishwasher. The Lock button is on (top of dishwasher). I have pushed that top button for 3 seconds. The button on the top and the "L" then both blink. The button on the top then stays on and the "L" light goes off. Since I can't get the lock light to go off - - my dishwasher won't tun on. Thank you very much.


First try unplugging the washer from powerpoint for 30secs..this may disable lock.if not, some washers will still work on lock if you hold the buttons you need. for 5seconds. eg try starting washer as normal but hold the button for 5secs....(Ps you m ... Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher

Maytag quiet series 200 model MD88750AWB Dishwasher doesn't work. Control panel only responds to the heavy wash button. When pressed it lights up along with three option lights. After about 10 seconds they go off. There is no mechanical response to the pushed button. There were no symptoms leading up to this problem. If you can give me a "head's up" about what to look for before I open up the control panel I would appreciate it. Thank You John


Hi\015\012\015\012\015\012\015\012\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficu ... Dishwashers

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My Maytag dishwasher model MDB600AWB, serial 18721619CN Quiet Series 300 will light up on the panel except for NORMAL WASH and START. It will not run. All other buttons work. It displayed the number 9 and the RINSE ONLY light came on after we got off the phone with Maytag. Initially nothing would light at all. We changed the fuse (it is NOT on a breaker) and it again didn't light. A few minutes later it did light the above mentioned buttons.


... Maytag Dishwashers

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button


That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

My Whirlpool Quiet Partner 111 dishwasher Model # GU2500XTPS7 control panel won't respond. There are 4 lights on, the normal wash light, heat/dry light, the lock light, and the start/resume light is blinking. I have held the heat/dry button for 5 sec. trying to unlock it and nothing happens.


Disconnect your circuit breaker for 20 minutes and then reset. It should reset your dishwasher. ... Whirlpool Dishwashers

Kenmore Ultra Wash Model 665 - 158* Front panel not working properly. Pressing Normal does not light that option. The only option that lights is "Quick Rinse", pressing this lights that option and also the "No Heat Dry" light. After a few seconds the lock light comes on. Looks to me that the "No Dry Heat" button is stuck on, which causes all the other things to happen Is there a way to fix this?


... Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

When I try to start the dishwasher, I can get the light to show I want it do do a normal load. Then when I hit the start button, it lights up but the machine will not sstart. Then in a few minutes the lights on the control panel at the top of the door go out. What can I do to fix this? The model # is KUDS011JBS0 tHE 0'S HAVE A SLASH ACROSS THEM THE TYPE IS 577-0 SUPERBA


Hi,\015\012\015\012Your control board has gone bad... you will need to replace it.\015\012The replacement is not very hard, just make sure that you mark where all of the wires go before removing them.\015\012\015\012Here ... KitchenAid Dishwashers

I have a whirlpool gold quiet partner iv model #gu2475xtvq and it is not moving from wash to rinse, instead the start button begins to flash as if the door had been opened and needs to restart. Also the control panel button for normal will no longer light up though all the other buttons do. this machine is only 15 months old


Ok I hope child lock is off? And you''ve tried cancel. If yours has the membrane buttons on top of the door, it very likely has water in them. If you remove the bottom kick plate, there should be a service information paper in there. It will tell yo ... Dishwashers

We have a Whirlpool Gold Quiet Partner IV model#GU1500XTKQ0,the normal wash cycle starts buts just goes into hang mode @ 76min remaining and just continues to wash, is it the control panel or the timer circuit board, all lights seem to work on the control panel


I replaced the heater element on mine and that fixed the problem. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Our dishwasher is no longer cleaning dishes very well and usually the detergent tab that we put in does not dissolve completely. Our dishwasher is a General Electric Model # PDN7800G00WW and several years old. The water here is very hard. On a separate note and a new development is the control panel seems to be messing up. When we press the ''speed cycle'' which is normally 37 mins it goes to 86mins and lights up the ''speed cycle:'' button. pressing the ''glass cycle'' lights up the adjacent '


Hi,\015\012\015\012There are various reasons for the Dishwasher not cleanig the Dish properly, From your query we can understand that, it must be issue with the Dishwasher selecter switch..\015\012\015\012DISHWAHER SELEC ... GE 24 in. Profile PDW7800 Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have a Maytag Quiet Series 400 model dishwasher that has lost all function. The panel will not light up. the number 3 is in the lock box. i held the dry button for 3 seconds but nothing happened. can you help me.


The control panel is faulty and must be replaced.RepairClinic. com is a recommended place to enter your model # and see the partsThanks ... Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have whirlpool diahwasher ,model DU1055XTSQ3,quiet partner -1. when i start the machine the folowings things happen: 1.the machine does not start . 2.Start /resume light starts blinking ,after few seconds ( 40-50 seconds), the pots and pans light also starts blinkng .after some time ( 1 minute ) the normal light also starts blinking .All three lights start blinking 3. I have done the following to rectify the problem from the book : alnernatively pressed heated dry and normal keys for


... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Kitchen Aid KUDIO1ILBS5... Normal Light keeps flashing green and wont start. When I press the cancel button, it flashes too. If I hold down the cancel button fashing light goes away on cancel button, but not the normal button... It continues to flash.


Hi,\015\012\015\012Close the door and to cancel that just press high temp and hetaer dry,then again high temp and heater dry and all the lights is going to light up, it getting into test mode.After that press cancel.\015\012 ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

Hi, I have the Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 .. aged about 6 years old .... When I press the on/off button 'on' the led display only shows the 'not started' message. When I press the on/off button 'off' the led display lights up momentarily with 'start' etc just before I have fully released the button. I have tried a new switch and the same happens so not that. ALSO i can sometimes see S1....> on the top panel and get the machine to show on the top panel the close door


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1516 seconds