Having problems with your Dishwashers ?

I have F1 fault on Fisher & Paykel DD601V2...how can you tell if mains filter is bad?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have F1 fault on Fisher & Paykel DD601V2...how can you tell if mains filter is bad?


... Dishwashers

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher & Paykel DW60. Fault: Will not start regardless of program selected. E.g. if "heavy duty" pressed, only light will flash, if "normal" is pressed, only this light will flash etc. All hoses (water and drain) have been checked and no crimps or blockages found at either end. All usual methods tried (e.g. cleaning strainers and filters, turning power off for a while etc). Finally, while lights are working, the machine makes no noise at all when a pogram is selected.


... Dishwashers

Fisher & Paykel DD603 model Upper Dishdrawer has F3 fault code. cycke starts, then stops within minutes. Water in tub after stopping is not hot. Temp sensor bad? Could you please send pdf of servie manula for dd603 please? Thanks [email protected]


F3 means your dishwasher water is too hot. Go to the link below and it will show you how to determine what is causing the error. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher Paykel DD603 Problem. Top drawer shows F1 and pump runs continuously. Lower drawer does nothing, no display. I think the Electronic Controller in lower drawer is fried and maybe the Mains Filter Board. Please help.


Yup, definately the bottom drawer controller, for some reason you can run a DD603 with no board in the top, so long as you have a board in the bottom, but not the other way around. This is the fault you get, constant F1 from the top drawer. If you ar ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Main filter board on my fisher paykel dishdrawer board burned


... Fisher and Paykel Dishwashers

My Fisher & Paykel DD 603 has the fault code


Check at bottom housing both top and bottom drawers for leaks. \015\012Pull the tube out, on the left side below the tub you can access to touch the bottom housing. Dry it out with a tower. Un plug the power cord at least 24 hor so the flood ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Fisher paykel nemo fault flashing light


... Fisher and Paykel Dishwashers

Fisher and paykel e8 fault code - Fisher and Paykel Dishwashers


... Fisher and Paykel Dishwashers

FISHER PAYKEL DISH DRAWER U3 FAULT CODE - Fisher and Paykel 24 in. DD-602 Built-in Dishwasher


LP is a setting for Low pressure. To reset your pressure to HP, hold the Programme and Eco touch switches simultaneously for 5 seconds. Once the setup mode is entered a beep is emitted andthe LCD is red with ‘HP’ or 'LP' displayed. ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Fisher and paykel diswasher f1 fault code - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


F1 fault code means the flood switch is activated. There is moisture at th e base of your dishwasher.\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Fisher and paykel dishwasher drawers are showing a F1 fault on the top drawer screen, But it was the bottom drawer that was in use at the time of the fault occured. The top drawer will open but the bottom drawer is locked. I need to unlock this drawer to get my cooking equpiment out. Please Help. I know that the F1 fault is a flood fault but how do fix it.


... Fisher and Paykel Dishwashers

Fisher & paykel dishdrawer ds605 f7 fault code. Lid failure. This is the second code (after F9- power controller fault).The lid of the dishdrawer will not raise and release the drawer. The lid is stuck in the down position. Assuming this is a power/electronic controller fault. Part numbers would be good.


You can force open the drawer without causing any damage. The actuators on each side will let you do that. But you push it back in unless you manually move the actuators for which you will have to take the drawer out of its housing.\015\012 ... Fisher and Paykel DS605ZW Dishwasher

Mains supply trips once connected ac mains. - Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher


This can only be some sort of "Short Circuit" to Earth. This can be Very serious. Please do NOT touch the unit when powered up, as it may be LIVE. This need to be looked at by an Electrician. ... Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher

F4 fault on fisher paykal dish drawer - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


F4 fault would inidicate the temperature sensor that senses the water temperature is faulty or the heating element is not working.\015\012\015\012Looks like you will need a technician to visit and have a look. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

Have Fisher-Paykel DD603 double-drawer dishwasher. Top drawer motor making loud noise. )Bottom drawer fine.) Still seems to wash and definitely pumps water but sounds like a "motor with a broken belt." Checked filter and rotating spray arm - no problems. (Found a little broken glass in filter; could be very old.) Suggestions?


If glass has gotten past the screen and into the pump, you may have a pcs. logged in the pump housing.\015\012Best way to correct this, is to remove the pump inlet and outlet lines and flush out with a water hose.\015\012Keep ... Dishwashers

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

Fisher paykel dishwasher dd601I runs complete normal cycle and finishes normally. 2-3 sec. after completion the washer motor srarts to run and the f1 fault (flood sw. activated) is dislayed. When the power button is pushed the fault spontaneously disappears and the motor stops. no moisture is in thre bottom under the tub and the normal cycle can be ru again with the same results.


Hi\015\012\015\012F1 code indicates an overfill condition which may cause when dishwasher can’t pump out dirty water due to a plugged drain hose.\015\012open dishwasher fully ,dry up as much water as possible the ... Dishwashers

Fisher and Paykel Dishdrawer-DS605SS F4 fault code


No temperature increase ... Fisher and Paykel DishDrawer DS605FDSM Stainless Steel 23 in Builtin Dishwasher

Dishwasher Fisher & Paykel F1 fault - what is it?


Hi and welcome to FixYa, Initially, the error code "F1"\015\012indicates a leak or overflow has been detected and flooding is\015\012possible. This would refer to the drain area below the tub of the\015\012dishwasher. In most occa ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

FIX F1 FAULT CODE ON FISHER PAYKEL DISHWASHER MODEL DD603


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fault f2 fisher paykel dishwasher dd601


... Fisher and Paykel Dishwashers

F9 fault on DD603 fisher and paykel dishwasher


... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

F4 fault on dishwasher fisher paykel DD605


... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0905 seconds