Having problems with your Dishwashers ?

I have a Thermador dishwasher # dwhd650gfp with displayed error code 2, I verified oily residue on dishes and caked up grease on sump trap filter. This unit is 14 months old. I first reckognized that the dishes were not drying completely after cycle, then noticed the cold grease accumulation in drain area, then saw "E02" displayed on message board. I have read through some blogs that this issue could be a defective heater assembly, shorted or open circuit at the connection at the control pan


Answers :

Hello,

Welcome to FixYa.
\015\012
\015\012You would've been correct in your suspicion , of Bosch built dishwashers prior to this more recent revisions including yours.
\015\012
\015\012Unfortunately that is no longer the case with the E02 error and this is what it indicates on your machine,
\015\012
\015\012
    \015\012
  • \015\012E:02 working relay error
  • \015\012
  • \015\012
  • \015\012
  • \015\012working (primary) relay failed in module - safety (secondary) relay running dishwasher.
  • \015\012
  • \015\012
  • \015\012
  • \015\012Replace power module
\015\012


\015\012


\015\012

I can send you a complete service manual of your machine if you'd like to post an email address. I think that may prove to be the best way to assist you in the long run.
\015\012
\015\012I'll watch for your post and we can go from there. Thank's for visiting FixYa today. Good luck.

Regards,

Macmarkus :)

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Thermador dishwasher # dwhd650gfp with displayed error code 2, I verified oily residue on dishes and caked up grease on sump trap filter. This unit is 14 months old. I first reckognized that the dishes were not drying completely after cycle, then noticed the cold grease accumulation in drain area, then saw "E02" displayed on message board. I have read through some blogs that this issue could be a defective heater assembly, shorted or open circuit at the connection at the control pan


Hello,Welcome to FixYa. \015\012\015\012You would've been correct in your suspicion , of Bosch built dishwashers prior to this more recent revisions ... Dishwashers

Dishlex global 450 _ how do i fix fill level time fault? displaying oF? Hi There, I have the above dishwasher and saw your advice on fixing fill levels - my display is showing the oF message and the pump to drain remains on whilst mains is connected. turning off mains does not clear message. holding eco button down does not clear message? is there anything else i should do in terms of removing parts to assist the process? I have cleaned out all of the drainage bowl and all is clear. i would pref


... Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

LG dishwasher LDF6810ST doesn't dry dishes anymore. Added more rinse aid like manual suggested but no luck. Also dishes don't seem to be as clean, some food is left behind, which wasn't a problem before. I use Cascade detergent and Jet Dry. There are no error messages displayed. Help!


... LG 24 in. LD-12BW5 Free-standing Dishwasher

My Siemens SD6P1S dishwasher is displaying the message E:25 and will not wash the dishes. What does this message mean and how can I fix the problem?


... Siemens Dishwashers

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

On our Hobart Dishwaher, Model AM15T, S/N-23-1000-664 won't start with message wrench & P2. The Thermistor is not open or shorted with resistance reading of 64 Kilo-ohms. I suspect that the Relay Board P/N- 892934-2F is not good. I installed the New spare board P/N 892934-1 Rev.F, but no display at all. Is this the correct PCB? Also the Thermistor is on one assembly with float switc. The new spare we had is only a Thermistor P/N F370609. I also checked the 3- Thermostat on the Tank and they are


... Hobart Dishwashers

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the message. Push reset button and washer starts back runs a couple minutes and then stops and then beep and gives the same message on control panel "washer arm blocked" again. There is "NOTHING BLOCKING" the washer arm!


The rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so \012\012\012\012check the jets for blockages... you might have to remove the arm to clean them properly ... Dishwashers

I have a GE Profile Dishwasher, Model# PDW7880J03SS that doesnt dry the dishes. I pulled out the dishwasher and checked the heating element for continuity with my ohm meter and got a closed circuit reading. I tested the voltage going to the heating element and got a 124V reading. However the dishes are still soaking wet after the drying cycle. What am i missing, what else could be wrong with the machine that the dishes won't dry at all?


Hi\015\012\015\012Check if the dishwasher is draining and filling properly is water temperature. Water temperature should be between 120 and 140 F. If water is not hot enough then heating element has gone bad, to check the element you'll ... Dishwashers

Fault PP It pumps and pumps with a gradual flow of incoming water but doesn't get anywhere. The top display reads 188 with salt and the other warning light on (sorry, I only know the danish word - afspaendingsmiddel), the front display reads iPP (the i is raised).


A leak which has activated the flood safety in the base, you can check this by pulling the machine onto a towel and tipping the whole unit forward ie raise the back of the machine off the floor so it is pivoted on the front feet at approx 45 ... Bosch Dishwashers

There is a 'Cr' message on the display panel, and none of the buttons respond while this message is displayed. What does this mean, and how can it be cleared so that the dishwasher can be operated normally?


Mine is doing the same thing right now. It started beeping again this morning after I wiped off the touch pad. I shut the power off to it at the box and when I turned it back on to try to make it work it just showed the Cr on the display. ... LG LDF9810ST Built-in Dishwasher

I have a Bosch Apexx. When I turned it on all I get a is flashing message "Not started". The LED display on the top edge is not working - only the display on the face of the machine. I have tried holding the start button and pressing all the other buttons and the same message keeps flashing...what to do?


Looks like micro-controller problem. Contact service center. ... Dishwashers

I have a Miele G 2470 scvi dishwasher. Machine displays F24 in display, lights flash, machine beeps and it won't run. Miele manuals seem to have no reference at all to error message displays. any thoughts?


... Miele Dishwashers

Dirty dishes The dishwasher does not wash the dishes properly seems to make all the normal noises but when finished its cycles the dishes are still dirty. Reading some of the other reviews sounds like I might have a inlet valve problem. Is there any way i can test if the inlet valve is functioning properly.


If water comes into machine then valve is ok.\015\012open machine when in cycle and look to see if spray arms are rotating\015\012if not, then take out and clean.\015\012spray arms only rotate with water jetting out of angled nozzle ... Dishwashers

Display reading 188min with snowflake symbol on display on top of door


... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Hi, I have a Miele G681 dish washer with an intake/drain light problem. I've read all posts about similar problems I could find both on this forum and others but I'm afraid I still can't figure my problem out. The intake/drain light starts blinking mid way into the dishwashing process. The dish washer fills up, rinses, drains, water is hot, everything seems to function just fine. Some time after the tablet drops from its door mounted container, and the time estimate reaches 46 minutes r


... Dishwashers

My dishwasher stops and displays a pf code when there is 38 mins left in the cycle. After it displays the pf code it restarts itself. So my dishes never get to go through a full cycle. What do I do?


Sounds like you need a new timer/control. They are preprogrammed to control the functions. Any change cannot be corrected. To replace try this link http:/ ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

My Hotpoint aquarius FDW75 dishwasher will not fill with water and when turned on the display reads H2O and then displays the code AO6


... Dishwashers

Dishes in the upper rack no longer get cleaned. I've been using this dishwasher since 2004 (purchased new), and have not changed the way I loaded the dishes or the detergent. I called the Kitchen Aid help line, and the rep simply read the owner's manual to me (e.g., stand a glass of vinegar in the dishwasher and run a cycle), which did not address the problem. Any idea what I need to do? Thank you!


It may be full of crud under screen. Remove lower spray arm, tower up to top, covers and you will see where the entrance to the impeller is full of stuff. ... KitchenAid Dishwashers

My Miele Dishwasher (Excella Series G 2630 SCi) fails to fill. I get the message "Water inlet - Open the stopcock". I checked the water inlet filter and looked for hose kinks to no avail. I even checked the non-return valve. When I start the dishwasher I can hear a low hum (Not the pump) for a few second before the error message displays.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

When the wash cycle takes longer than the time stated on the display, and when the dishes are done, there is about three inches of dirty water in the bottom of the drawer . The repair technician replaced the rotor this week, and says he needs to replace the display, but its still not working right


A couple of things to confirm first\015\0121. is the second drawer working oK - i am assuming you have a double drawer model?\015\012\015\0122. Are you not seeing the wash cycle time on the display? why does the technician want to r ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Have a 2+year old LG LDF6810ST dishwasher that shows no error codes but is not cleaning like it used to. Have city water, do not leave excess food on dishes when loading, am only using powder after reading other tips about the use of gels. There is excess moisture in the tub and on dishes after the cycle. Does not appear to be drying as it previously did. Any ideas?


Try these things in order:-Try to use a name brand powder, rather then a generic. Even a small box. I had similar problems with my LG dishwasher when I tried to save money by buying a generic powder. My dishes did not get clean and whi ... LG LDF6810ST Stainless Steel Built-in Dishwasher

My deceased parents have a GE dishwasher (don't know the model number - can't find it on the machine and can't find the paper work) that stops working shortly you start it and displays a message on the front panel that says "Blocked wash arm - check for wash arm obstruction - restart". We restart it and get the same message shorty thereafter. This happens when the washer is COMPLETELY EMPTY, even when we remove the bottom rack. It first started after several month of inactivity. We'll just t


Could be false sensor input, could be that the arm is not turning, I am not sure how old your machine is, but age could play a part if the arm is "in fact", not turning. If you are not mechanically inclined, I would suggest that a qualified repairma ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1055 seconds