Having problems with your Dishwashers ?

Water not flowing into - Dishwashers


Answers :

You have a tap on the wall..then pipe to washer...............ware the pipe fits onto the washer there is another tap............which can refuse to open...........it is poseble to swap this top with 1 off an old washing machine..................\015\012
\015\012cheers
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.


This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Water does not come into the dishwasher. can hear the pump, the heater works, the indicator lites illuminate, but water does not come in. The water supply is hooked up and turned on, there is good flow to dishwasher connection, but no water inside the dishwasher during operation.


Hi,\015\012Usually the problem is the soleniod valve that lets the water into the dishwasher...\015\012\015\012here is a tip that I wrote that gives many more details about this problem...\015\012\015\012Dishwasher ... Dishwashers

Siemens dishwasher help i have a siemens dishwasher with no manuals and on my fresh water pipe there is a box which has a electric sign on it this also has another arrow on it is this a flow arrow? my copper pipe has my outlet on the top should my outlet be underneath to suit this arrow and the water is flowing down and not up the pipe thanks ****.


My siemense dishwasher (2 month old) stopped working\015\012No matter which program I choose, after 1 min the program stops and I get "tap" symbol on the led display. \015\012Instructions says it might be a problem with the water source b ... Siemens 24 in. SE25T250 Free-Standing Dishwasher

Model FDB4315LFC2 Serial TH80658596 It is only 20 months old but Does not load with water. I have checked water line into white valve and water is flowing, but it does not come into the dishwasher. If I manually put water in the bottom of the dishwasher it works fine through the cycle until it is time to pump in more water. There is a sound but no water comes through the valve.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. As you have already checked the water line for clogs/obstructions and the water is flowing but wont fill ... Frigidaire Dishwashers

No water will enter the dishwasher, There is no problem with the water supply or the supply line. The water flows from the supply line to the dishwasher connector but does not enter the dishwasher.


The water-inlet valve lets water enter the machine. Make sure it's not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if you get power to valve when unit is put into operation ... KitchenAid Dishwashers

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

Not getting enough water flow into the dishwasher, suspect that a filter is clogged due to recent work on the waterline in the kitchen sink. Need to know where the filter might be located (on the dishwasher or on the intake valve before the connection to the dishwasher hose)? Also would I need to disconnect the water supply to pull out the dishwasher for access to such a filter.


You didn't specify a brand but most dishwashers don't have a water "filter." They may have an inlet screen at the water valve, which is typically located under the dishwasher. Generally, the lower front panel will have to be removed and you should ... Dishwashers

Hello! My GE Dishwasher (Model # GSD2000G00WW) will not fill. The water supply is flowing properly after cleaning out some lime and mineral deposits, but no water is going into the machine. If the water flow valve needs to be replaced (?), is there a local distributor in the Cincinnati/Blue Ash area in Ohio (zip code is 45242)? Thanks! Steve Brodbeck


I need to know is the water not going in the machine at all in other words when you switch on the machine with the tap open can you hear the water flowing,if you can here the water flowing check the hight of you drain hose if it is too low down you w ... Dishwashers

Water not flowing into dishwasher. I've taken door off, detached 1 lead to the solinoid. It shows 987 ohms resistance, can feel AC hum when 110v put into the coil - but no water flows (water attached). Where do I go from here?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your post and the findings of the valve resistance of 987ohms, ( normal is 1Kohms ) it sounds well within acceptable range, however the valve can sti ... Bosch 24 in. SMU70 Built-in Dishwasher

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

The dishwasher won't let water in nut will pump out have checked water flow through hose which is ok but when attached to dishwasher it wont fill with water


The water-inlet valve lets water enter the machine. First Check to see if the valve is getting water. Make sure it’s not clogged. There is a screen on the inside of the valve, this sometimes gets clogged up with debris. Check to see if yo ... Dishwashers

I had a problem with my dishwasher popping the breaker. I opened the bottom and found burnt up wires. I fixed those and now the dishwasher stays on and begins its cycle (by draining) but the water is not flowing to the machine. It has supply, and I just now replaced the water inlet valve- no difference. The water was working before the breaker issue. I'm wondering if it is now something as simple as a clog somewhere since the washer sat unused for a month; or, if it is something more compli


I read your previous problem. This appears to be separate problems. The first was likely a loose wire. When a wire has a loose connection they build heat and can melt. The current issue would seem like the float switch is stuck. The float switch is ... Bosch SHU9925UC Built-in Dishwasher

Dishwasher problem dishwasher begins to wash, water flows in, then both first and second green indicator lights flash together and the cycle does not complete. I have cleaned the filters, removed water that's left in the bottom of the dishwasher.


My dishwasher Indesit DI67S will not run on the number 1 cycle. It will fill and then when that programme finishes it jumps straight to the drying cycle missing all the rinses out etc. If on the number 2 programme it goes all the way through but then ... Indesit 24 in. DI67 Free-standing Dishwasher

Bosch dishwasher inoperable, clean water flow, not running


Press drain and cancell button at the same time ... Bosch 24 in. SHU43 Built-in Dishwasher

I've had a Miele G892 SCU PLUS dishwasher for a long time. Today a problem started that results in a flooded floor. Water keeps flowing into the dishwasher - even when the unit is turned off. It seeps in very slowly, but within15 minutes there is enough to overflow & flood the floor. My guess is that there must be some kind of sensor that isn't working, or the coresponding mechanical switch that shuts off the water is worn or slightly stuck open a bit? Anything I can do / check, short of the re


... Miele Touchtronic G892 Built-in Dishwasher

Dishwasher filling I have a Diplomat dishwasher. When it fills with water, only a certain amount flows through into the machine and the water backs up and floods the kitchen


Check to see if you have anything plugged ... Dishwashers

Water will not flow into dishwasher . will complete cycle but no water in dishwasher.


Start with the water going into machine chek under the sink fill hose and check with a meter the water valve its normally one or the other.let me know with a 4 thumbs up post ... Dishwashers

Water leak have the Ge triton dishwasher (Model # GSD5320D02BB, bought it n 2001) and currently have very small amount of water leaking out of the door during a run cycle. I did check levels when running and that seems to be fine......meaning the dishwasher is level and not an over-flow problem. My next thought is maybe it is a faulty door gasket. So my question is, where is the door gasket located and how do I replace it? (and where do I order this part from?). Looked for diagrams to follow and


They are in the bottom left and right of the door opening. GE likes to use L-shaped, molded and ribbed seals on most of their models - hopefully also on yours. Typically these can be removed by hand and easily replaced without taking anything apart. ... GE Tritonr XL GSD6260JCC Dishwasher

No water flow to dishwasher disconect the plug at flowing switch 120V no power at water valve plug


Check to ensure you have proper volatage at the connection box behind the toe kick\015\012 the you will need to open the door to check the door switch for both voltage and continuity ... GE 24 in. Profile PDW7800 Built-in Dishwasher

No water flowing to dishwasher, I check the power to flow switch plug 120v no power to water valve


Check to make sure both sides of your door switch is closed as well\015\012 if your door switch is not closing properly it will not send voltage to the water vale ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Dishwasher over flowed this morning. I hit the cancel/drain button and the water drained but kept coming in from the inlet valve. Had to shut the water supply off to the dishwasher.


Sound like the possibilty of the inlet valve regardless once the door is opened shut down power to the unit unless you have mulitiple failures going on at the sametime. ... Whirlpool 24 in. GU980SCG Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1686 seconds