Having problems with your Dishwashers ?

Start/resume button flashes 3 times when engage button


Answers :

Hi .... you have a bad main board
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Start/resume button flashes 3 times when engage button


Hi .... you have a bad main board ... Dishwashers

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

My Whirlpool Gold Quiet Partner III was DOA when I went to use it today. I unplugged/plugged it back in, at which time the "China Crystal" LED flashed a sequence of 3 flashes, then 3 more flashes, pause, 3 + 3 more, pause, 3+3 more, pause, etc., etc. And it would not run on any other cycle, but it did seem to run thru that one OK. Upon completion of the cycle, it was DOA again. Did the "Normal/Air Dry/Normal" button sequence, and now the Rinse Only button is steadily flashing. Any suggestions? I


When the rinse light is flashing steadily then the reset procedure for your model is pressing the "Normal/Air Dry/Normal" buttons.\015\012\015\012If it did not reset your dishwasher the control board must have fa ... Whirlpool GU2400XTP Built-in Dishwasher

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Start button keeps flashing machine will not run on any program. I've tried holding down the start and time button which in the past has allowed me to restart the machine. This isn't working this time


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

I have a kenmore elite dishwasher model # 665.1392 I had set it for a wash with th 4 hour delay and that shut off and now the complete blue button is flashing 4 times with a pause and then flashes 4 times again. If I open or shut it, it beeps 15 times. I tried doing the normal wash - heated dry back and forth trick but no luck with that. Any suggestions?


... Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

Hi, I have a fisher and Paykel Nemo dishwasher. It takes water in with no problem. But it stops after fill up the water and the led near "start" button keeps flashing. (flash 6 times and stop for a second, then flash another 6 times, so on) By the way, Heat element has been confirmed works. Any comments? Many thanks.


... Fisher and Paykel Dishwashers

Whirlpool APD5550 Dishwasher, cycle does not start, green light on start button flashes 6 times, pauses, flashes 6 times etc. can you please give me some indication what the problem may be. Thanks


... Dishwashers

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

When I depress the start button, the timer is clicking to engage and begin the cycle, however, the dishwasher does not start. Other times, there is no noise whatsover when I press the start button and neither does the dishwasher start. If I don't use it for say 2-3 weeks and try again, it starts working for a period of a few months, but then the same thing happens again down the track. This has occurred about 4 times.


Hi.Resetting the breaker means turning power off and back on from the main switch in your house. Same as disconnecting power cord.I am sure that in this case "tripping the breaker" will not help. Repairing appliances is not th ... Dishwashers

I have a kenmore dishwasher mo. no.665.17039401 the clean green light flashes 7 times and it keeps doing that if i try to start the dishwasher on the start button a red light flashs three times what do how do i fix it .i made shure the door was locked


... Dishwashers

My Whirlpool ADP 5406 runs for about a minute and then the light flashes four times, repeatedly. What can I do to fix this? (I can still get the machine to run its cycle by holding down the start button, but the light will flash four times again on completion).


Hi and welcome to FixYa. I am Kelly. \012 Usually this symptom also shows an F7 error code. You will need to remove the lower wash arm (NOTE INSTALLED POSITION) Also you will need to remove the metal grate under the wash arm to ... Dishwashers

Dishwasher problem Hi there i have a whirlpool DWF 415, the power button flashes green nine times then stops then flashes nine times again and will not start! Please help! regards sharon


Hi Sharon , Im not finding your model number dwf415. See if you have high temp wash and heated dry buttons on your dishwasher. If you do, press high temp wash, heated dry, high temp wash, heated dry in that order. This will run the service mode ... Dishwashers

Our whirlpool ADP 6565 dishwasher stops very close to but short of the end of the cycle, with the on-button flashing. If we press that button for a few seconds, it starts again and completes the cycle. I have cleared the filter on the inlet hose because we use tank water which does have particles in it frm time to time, but this made no difference.


It appears that you have a timer malfunction. at the point that the timer stop, you need to listen closely to any sound from the timer. if no sounds emerges, repalce timer ... Whirlpool Dishwashers

Whirlpool Dishwasher ADP 2652 WH at the end of a clean cycle, the pre rinse button remanins on, the "end" light flashes constantly and the on/off button flashes 4 times in a repeating manner.


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1039 seconds