Having problems with your Dishwashers ?

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or workshop ma


Answers :

Hi.

The switch on this machine's control module is electronic. I do not think you will find a relay.

In normal conditions the button is not supposed to stay latched If the button is defective you may get the same problem when the faulty button closes and opens the circuit repeatedly canceling the cycle. If you hold down the button, it stays latched and cycle may go on.
When the on off is down the reading on the appropriate pin will be 10 Ohms.

Electrolux (who built your Dishlex) does not provide schematics for the board in the control module, as this is not supposed to be serviced. It is the same with most appliances.

You can test the button finding appropriates pins in the wiring harness connector and reading impedance to find out if button is closing and opening. The test is done with power disconnected (disconnect power cord or trip circuit breaker).

I do not have manuals for Dishlex. I may have the service manual for the Electrolux equivalent. The problem is that is in a foreign language.

Regards.

Ginko.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or wor


Latching relay or door lock assembly need for you to check on that model number 560 silent range wont come out on dishlex's site should be a dx followed by some numbers try also to shut off the main power for 7 minutes to the unit to reset the contro ... Dishwashers

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or workshop ma


Hi.The switch on this machine's control module is electronic. I do not think you will find a relay. In normal conditions the button is not supposed to stay latched If the button is defective you may get the same problem when ... Dishwashers

I have a dishlex global 300 on which I removed the front cover a black wire came loose and I didn't know where it came from thanks to jyackle5 I have fixed that issue. The problem I have now is the eco light flashes and that's it (nothing else functions). I removed the front panel as the bottom door seal had blown and junk oosed behind the front panels I washed the junk out and cleaned the hole washer while I was at it the bottom of the washer (where the heating element is) over filled so I tipp


Easy fix, Use a bit of force and pull the dishwasher out.Get a few towels and tilt to the left. Water will drain out. Push back in. wait 10 mins and turn on.\015\012\015\012\015\012\015\012Regards ... Dishwashers

Candy csd-68-80 all four lights on front panel lit, started flashing within few seconds of switching dishwasher on, no previous problems,dishwasher not overfilled, checked manual which said too much inlet water unsure what this means or how to check it. do all usual cleaning,salt,arms etc. had dishwasher about 14 months and use it every day never had any problem before


... Candy Dishwashers

I have a Kenmore front load washer, model 970-C4909700, the problem is that, despite reducing the amount of the detergent (high efficiency), to the point that the laundry is not clean washed clothes smell with detergent, we happen to have a very sensitive sense of smell, probably other people would not detect anything. This means, however that there is still a lot of detergent left. For this reason, after each wash I have to do an extra rinse or even a wash without detergent. I have seen tha


HiThe smell usually comes when the washer is unable to drain water completely, you can run your washer at its hottest temperature setting with 1 cup of vinegar inside the unit. After this take off the bottom front panel and clean it compl ... Kenmore Dishwashers

Dishwasher is leaving soap on my dishes in top rack. Was using a gel soap heard that switching to a powder would solve this problem. Did not work. I also cleaned dishwasher with Tang kool-aid, but did not work either. Help


Do you have a water softener?\015\012\015\012I recommend powder, cut back to a spoonful of soap and use a rinse aid.\015\012\015\012Another good cleanout is water softener cleaner, as long as your tub is not metal. ... Dishwashers

We have the same problem. At first, we were getting a horrible detergent film on everything. We thought that was because the detergent cup wasn't opening or the water was too hard or not hot enough. We kicked up the rinse agent as high as possible, switched to a liquid detergent, and only placed shorter items towards the door. The cup still wouldn't open consistently and our dishes still needed to be re-cleaned. We stopped closing the cup. No change. Why would liquid detergent leave a powder fil


You dont need a new dishwasher. it is your water that is causing the film and residue. go to www.dishwasherfilter.com. they have an awesome product that is affordable and g ... Dishwashers

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

I have a bosch SGV43A03GB/42 dishwasher. The cups / plates were coming out dirty so I did all the drain cleaning and ran finish dishwaher cleaning fluid. What I noticed was the top arm wasn't rotating and the source of the problem. I took out the arms and cleaned the holes to ensure no blockages but still a problem. I bypassed the door switch and found that theer was no water being pumped out to the pipe that leads to the top rack. I opened the two torx screws and looked beneath pipe to find wha


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SGV43A03 Built-In Dishwasher

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

Dear Sir/Madam,I have owned a Beko DW450 slimline dishwasher for 13 months and used it only twice, i wanted to use it last night but when i switched it on the drain pump activated and would not switch off. I powered down the dishwasher to see if that would reset it but unfortunately when i started it again it did the same thing - drain pump activated but would not stop running, it is impossible at the moment to carry out a wash programme. Does anyone have any idea on this problem. Thanks, Patric


... Bosch SHU5315UC Dishwasher

Hi There I am having a problem with my Candynova CD122J Dishwasher, The problem is the water is not emptying out of it, I have checked and cleaned the filter and made sure there was not cutlery etc caught in it, Have you come across this problem before or would you have any help on this?? Any help would be well appriciated. Regards, John 00353852113372


Water pump could be out could be restriction in the hose that runs into the sink drain ... Dishwashers

Hi I went to put my Bosch dishwasher on this morning only to find that it would not come on . there was water in the bottom of the dishwasher so i cleaned all the water out and cleaned all the filters but my dishwasher would still not work it was only when i went t o disconnect the dishwasher from the water supply did it come on Can you please let me know what problem i have with my dishwasher and is it likely to happen again


Hello,\015\012\015\012This video will help you fix your ouch dishwasher.\015\012\015\012 ... Bosch Dishwashers

Hi i have a problem with a candy 122, the problem is the soap door will not open to allow the soap tablet out? have cleaned it all and made sure all the jets are clean and the soap door opens up when operated manually. any help would be great please


Please read your instruction manual. If you do not have download from this web:www.fitness.manualsonline.com or www. retrevo.comGod bless you ... Dishwashers

A GE triton dishwasher causes hammer noise when stops filling. The sink faucet works fine as do all the other faucets in the house. I cleaned all of the traps in the dishwasher. Because the sink works, I don't think it is a sink valve problem. I turned off the water to the house and drained the system, the air chambers should be good. Is there some component of the dishwasher that could be causing the noise? Would cleaning the pump help? If so, how would I do that?


The cause of the hammering noise, (slamming) is due to the water inlet valve on the Dishwasher (DW) shutting off abrutly once the DW reaches the proper amount of water.\015\012\015\012If this is an older DW, you might want to replace the ... GE Dishwashers

We have a Miele G863SCVI Plus. We have a problem with the Inlet/Drain light staying on. Originally, if we turned the dishwasher off and then on again it would work. Now it won't. I have cleaned the filter out but wonder if there is something else that needs cleaning. I have never had a manual and cannot download it from the websites that say they have it. I would really appreciate it if you can help me


Hi.Check that the drain hose is responding to specifications. This machine suffers from siphoning problems caused by incorrect drain settings. Siphoning means that the water flow back inside the machine from drain hose, causing drain ligh ... Miele 24 in. Incognito G863 SCVi Built-In Dishwasher

My kew alto force pressure washer would normally cut out and start again in about 30 minutes. now it will not start at all. i have dismantled the pump from the housing and everything looks ok even the pressure switch is very clean. Could it be the on-off switch that is faulty. any help would be appreciated. fg


... Pressure Washers

I have a Quiet Guard Standard model #587.151524 that is not cleaning the dishes. I took the bottom spray arm and screens out and cleaned them, (they had a heavy buildup of what I would say is calcium. The arm cleaned up fine but the screen still has some areas that will not allow the water to drain. I tried CLR and it helped but the screen is still probably 60% clogged. Do you think this is the problem getting the dishes clean and if so do you have any suggestions about how to clean the screen?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Kenmore 24 in. 15689 Built-in Dishwasher

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

Email [email protected] i have a cma c dishewasher It was going through a cycle and it just stopped. there is power to the switch (Cycle starter switch on front.)also the heater also is now not working What could be the problem the relay switch??


... Cma Dishmachines CMA-66L Dishwasher

Maytag MDB 4000 AWB. Not cleaning. not getting water now. pressure was low when i was getting water. . Soap dispenser would not open as well. I replaced the motor on the soap door. cleaned the float switch. Tested continuity and cleaned out water inlet valve. Still not getting any water


... Maytag Dishwashers

We have a model GU1200XLT1 dishwasher. For over a year, we have a problem with debris being left on the dishes/glasses. We got sandy like debris in the left front section, top rack, after it has cycled. Mostly on the outside of whatever is in that part of the top rack. How do we get rid of this debris problem? Is there some filter that needs to be cleaned? We also have problem with mold/mildew inside dishwasher. I have cycled it with bleach, ammonia, or vinegar, which temporarily sol


... Whirlpool Dishwashers

Zanussi Aquasave ZT.685 MODEL TOYPE 911N83-7F SERIAL NO. 04450004 PROBLEM: UNIT IS SWITCHED ON. UNABLE TO PRESS SWITCH TO SELECT WASH PROGRAMME. SWITCH DOES NOT APPEAR TO ENGAGE EVERYTIME. INTERMITTENTLY THIS DOES WORK AND WASHES ON ONLY THE "QUICK WASH" PROGRAMME. WOULD BE GRATEFUL FOR YOUR SOLUTION.


... Zanussi Dishwashers

Diswasher A couple of days ago my dishwasher would not start, there are lights on the front panel and it starts a washing programme but doesn't actually wash anything. I removed the filter from inside the dishwasher and it is full with water, it seems like there is a blokage somewhere. Would a blockage cause the diswasher not to start. Any help on this problem would be greatly appreciated.


Jhgf ... Whirlpool 24 in. ADP6940 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1055 seconds