Having problems with your Dishwashers ?

Its a whirlpool dishwasher washed dishes last night dishes were clean but rinse water was still in the tub now no lights come on the touch controls its like its dead, i checked power and got it to the circut board but dont know how to check any thing else


Answers :

Hi.... you have a Bi-metal bad .. It has opened You can by-pass it by using one wire and I bet it lights up ... dont leave it by-pass..... The bi-metal is right on the main board
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Its a whirlpool dishwasher washed dishes last night dishes were clean but rinse water was still in the tub now no lights come on the touch controls its like its dead, i checked power and got it to the circut board but dont know how to check any thing else


Hi.... you have a Bi-metal bad .. It has opened You can by-pass it by using one wire and I bet it lights up ... dont leave it by-pass..... The bi-metal is right on the main board ... Dishwashers

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

No power unit went dead checked power to base of unit ok also shut off breaker for 10 minutes to see if it will reset, no luck. Also removed inner door panel to reveal circut board to look for a reset or small fuse, none evident.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

My dish drawer won's start. there seems to be no power. i checked the plug and it is fine, but the dw is dead. what are some things i can check? it is a dish drawer - single it is two years old never did this before wall plug has power there are no lights, no electrical activity at all


... Fisher and Paykel DD605I Dishwasher

Dead dishwasher? I have an Prima LXP600 dishwasher that doesn't work - no power light, no beeps, no anything. I've changed the fuse and used different power sockets. Is there anything that I can investigate, or alternatively is it likely to worth calling an engineer? The machine looks almost unused (was in a repossessed house that I bought, so no history), so I'd like to think that it's got some life left in it!


Please find some help from the link below;\012\012\012http://www.repairclinic.com/Dishwasher-Repair-Help ... Dishwashers

Hi, I have a Hotpoint Aquarius DWF31 Dishwasher. The dishwasher was put on last night and this morning although it looks liked it as cleaned is has not drained. But now there is no power at the machine. I have checked the fuse at the plug which is ok and also there is power at the socket. Is there a fuse inside the dish washer or any thing else i can check


... Hotpoint Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My du943 dishwasher will not power on....it looks like it lost power after the dishes were washed and before the water drained. The fuse is not blown, the power box underneath the unit appears ok, and I checked the thermal fuse after reading other posts with the same problem. What to do from here?


... Whirlpool 24 in. DU930PWP Built-in Dishwasher

Kenmore dishwasher... filled up with water and its lights went off.. no buttons work acts like no power. check the house fuse box - ok ... check the 2 door switch - ok .. checked the thermal fuse - ok ... so, i picked up a new board and changed it out. still wouldn't run.


Did you check power to the unit? Double check the common and grounds. When servicing I will disconect(unplug from wall) power to the unit. Is it pluged in? Use another outlet(the outlet under the sink may be wired thru a switch for a disposer)even ... Kenmore 24 in. 16032 Built-in Dishwasher

Maytag dishwasher, control panel is dead, has power to board,but there are no lights on the panel when you close the door, like it normally would. any ideas I replaced the board with no succes. thanks Bruce, B&L Appliance


I think you have diag your problem . your have power to the board . so the inter lock switches are ok . and no lights . if you look at the printed pc board i think yoy may be able to see that one or more ... Maytag MDB5100A Dishwasher

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

...dead Hello, I own a Bosch SHU3036UC / U12. It has never been a problem until yesterday. The unit simply wont power "On". I checked my circut breakers and GFIs, but not an issue. The dishwasher is simply "Dead". Do you have any suggestions?


CHECK DOOR SAFTEY SWITCH OR TIMER MOST LIKE SWITCH ASSOCIATED WHEN DOOR IS CLOSED ... Bosch 23 in. SHU303 Built-in Dishwasher

'Dead' DU1100XTP The dishwasher will not start - no lights at all - no indication that anything's working (although I confirmed the unit has power). I've seen numerous posts regarding the control board - is there a problem with these in general? My unit is just beyond the warranty (naturally!) so I'd like to know if there's been any concession made by the manufacturer due to the number of problems. I'd gladly replace the board if Whirlpool would send me one. Thanks.


This may sound simple but... make sure its plugged in all the way. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Our LG dishwasher is about 4 years old Mod #:LDS5811ST. It stopped dead in the middle of a load of dishes and shows no sign of receiving any power---no lights, etc. We checked the outlet and power is flowing to it. Thanks for your help.


... LG Dishwashers

I,ve got a prima LPR450 and it won't switch on, i've checked the obvious things like the fuse, circuit breaker and wires in the plug and they ere all fine. when i push the power button there is a faint clicking sound from inside the door.


... Dishwashers

My bosch dish washer will not come on.I checked to see if their is power and their is, no lights on door or any thing.


... Bosch 24 in. SHU43 Built-in Dishwasher

Kudl03fvsso dishwasher Was working fine, now dead no lights ,nothing. Has power, checked thermo fuse in door and door switch both ok seems like this is a common problem. any suggestions?


... KitchenAid Dishwashers

My dishwasher's lid is stuck down and won't retract. I have a Fisher and Paykel DD605 dishwasher, and I think I must have placed some dishes in there that were too big for it and the lid got stuck. It's now showing an F7 error and refuses to do anything other than beep at me. I've tried turning the power off and back on, but it persists with the error. Is there a way to get it to reset and retract the lid? I've read that in situations like this, when people get repair technicians to com


The error code f7 stating that "the communication time out error"this are all the reason for the error1.the motor control micro has crashed and is not responding to communication request.2.the hardware communication link from ... Dishwashers

Whirlpool dishwasher DUC600XTPQ acts like it is dead..nothing happens when I push the buttons, liek the power if off but I checked the breakers, now what? Help!


Sounds like control is bad. cut the power, open door remove six screws at top of door the control panel will be loose. suport this remove black cover over control board by releaseing tabs shown by arrows. there is a fuse at lower right corner of boa ... Whirlpool GU2400XTP Built-in Dishwasher

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

Having trouble with dishwasher- I feel like dishes are not getting clean- will replacing circuit board on dishwasher help dishing become cleaner?


You may need to clean out the filters that keep food from being pumped up to spray out of the sprayers. This will depend on your make and model as to how to do this. Clogged filters will reduce the amount of water being sprayed. Try opening the do ... Maytag Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1519 seconds