Having problems with your Dishwashers ?

I turn on the dishwasher you hear a cycle of water and then turn on the light F7 and the dishwasher stops.


Answers :

F7 means a water flow meter problem. Either your dishwasher is not getting proper water pressure, or the flow meter is bad. Check to make sure you have good water pressure to the dishwasher, and then check that your water is coming in at a good flow rate. If both of these are ok, then replace the flow meter. If your house water pressure to the dishwasher is good, but your water flow coming into the dishwasher is slow, then your dishwasher water valve is probably plugged. Some valves you can take apart and clean out, and some you will need to replace. Good Luck,
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

I turn on the dishwasher you hear a cycle of water and then turn on the light F7 and the dishwasher stops.


F7 means a water flow meter problem. Either your dishwasher is not getting proper water pressure, or the flow meter is bad. Check to make sure you have good water pressure to the dishwasher, and then check that your water is coming in at a goo ... Dishwashers

My Teka Dishwasher DW7 80 FI does the first water intake operation, it sounds like rinsing, and the you hear the pump evacuating the water and two beeps as when it finishes the complete cycle. About 6 minutes. Then Stops. The lights that stayed on says error E8 according to the manual. I have done the suggested fix as ending the cycle manually and turning off and on the DW. I tested "many" times in various modes and the same preemptive end.


Hi.E8 is alternate washing system malfunction.The alternate washing system consists of a valve located in the underside of the appliance and connected to the impeller motor. The valve opens and closes switching spray on and of ... Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

Delonghi trend dishwasher you select programme and it starts and you hear the pump start and expell water and then u hear water going into machine for 10 seconds or so then it stops then programme selected light starts flashing and the dishwasher starts to heat as though it is in the drying part of the cycle


Please provide the full model number of the dishwasher.\015\012\015\012have you tried to turn the power to dishwasher off and back on.\015\012\015\012What program do you start with? Have you tried the rinse only cycle? does it ... Dishwashers

My GSD3600 GE Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit


Hello Greg,\015\012\015\012Your diagnosis is pretty good, but the buzzing suggests it may be the capacitor for the pump motor that has failed rather than the pump motor itself. The capacitor phase-shifts the AC current for starting the mo ... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher

Dishwasher will not finish/start a cycle. The washer filled with water and during the cycle I heard a pop like someone knocked something over in the kitchen. I smelled an electrical burning smell. All the lights and the buttons work on the front panel, but when I try to start I hear an electrical buzz like it is trying to start, but nothing happens and after 3 seconds the electrical buzzing stops and the lights on the panel flash. I removed the dishwasher and found that when I hit the start butt


... GE 24 in. GSD3960LSS Stainless Steel Built-in Dishwasher

Just turned the dishwasher on at the wall and tap after it's been sat off for a day. It's done one cycle (eco) and now doesn't seem to be doing anything but flashing. The two lights flashing are the power and eco lights. I have tried turning it off on the console but it turns itself back on and continues flashing. It sounds like it's whirring but I can't hear water. It did have a small leak when we first plumbed it in if that makes any difference?


... Hotpoint 18 in. DC27 Slim-Line Built-in Dishwasher

Smeg Dwi409c dishwasher is stopping 3 minutes into cycle with no fault lights or anything, I hear it fill with water but then stops, but I do notice the water is not draining which I assume is why it is stopping, correct me if I am wrong. Have removed the filter but still not draining. Any ideas?


... Smeg Repair Pcb / Module Dwi409c

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

We have a Haier DW12-PFE2-U dishwasher thats 2 years old. The cycle stopped yesterday leaving an amount of water in the bottom and all of the program lights are illuminated with a recurring beeping sound happening. It says in the booklet that the drain hose is too high or bended. But its not. The display does show the time when a cycle is selcted but nothing happens. The dishwasher turns on and off normally. Can this problem be rectified? thanks!


Refer userr guide on page 21. It reads...\015\012\015\012When all the programme indicators " J" blink.\015\012Have you checked whether:\015\012the door is closed properly.\015\012\015\012 ... Dishwashers

Fridgidaire FDB1250REC dishwasher comes on, fills some water in bottom then cycle stops but can hear motor turning on and off, water will drain when I try to start cycle again.


This seems to be the "anti flood" device at the base of the washer is triggered due to water at the base of the washer. This safety device consists of a polystireene float and a micro switch that detects water leaks/spills and automatically puts the ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

We have a Kenmore Elite Dishwasher #665.1646 - 5yrs old. On Friday nite, there were no problems but last nite the lights would not go on when cycles were pressed ( or Start). Checked the circuit breaker and it was OK. There is nothig caught in the bottom and the overfill float is functioning. I pressed Hi-temp and Air dry alternately and all the lights lit. I pressed Smart Wash, then Start and it did not go on. I can hear it draining but no water seems to flow and then it stops. All light t


The thermal fuse on the control panel. There isa couple of wires that lead up to a white box with the fuse in it. Thatis the problem. If you are good with a volt meter or light and youplace it across the fuse, if it is bad the light will light ... Kenmore Dishwashers

Dishwasher sounds as if it starts cycle, then stops, bleeps, and Fat and prewash lights come on. Manual says to turn off machine, turn off tap, wait 30 seconds and turn it all back on, but it doesn't make any difference. Manual says 'If the above does not solve the problem, check that the water feed pipe is not blocked' however, it doesn't say where this is, or how to do it. Please help!


Hi.You need to check the water inlet hose, that is the hose connected to house water faucet at the back of the dishwasher.Checck for blockage in the hose and ensure that the inlet hose is not blocked or kinked.If t ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

Siemens auto 3 in 1 dishwasher stopped working. lights are on. Machine is humming for a while, but no water enters the machine. Water tap is turned on, filters are clean, no bends in the hose. timer is counting down as during normal washing cycle, but nothing happens


... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

I have a General Electric pdw7880J03ss dishwasher. Tonight, I went to start a load of dishes and the Heated Dry option wouldn't turn off without the lights going to RINSE ONLY. Then the 1hr setting started coming on. Then was able to get the load to start but then it stopped somewhere in the cycle. Now, no lights will come on the panel though I can hear the beeping. Dishes appear to have washed...


Hi\015\012\015\012Press and hold the heated dry button for 15 seconds to reset\015\012the control, if this wont work then it means that the control board is bad and\015\012should be replaced. Hope this helps...please post back for further ... Dishwashers

I have a Dishlex Global 300 dishwasher that stopped working mid-cycle. I had to sponge out all the water. Now none of the buttons do anything and none of the lights come on. When I turn it on at the power outlet it gives a single beep, but I cant get it to do anything else. I've opened it up and there is no water or dampness anywhere inside. Any ideas?


It is your control board inside your dishwasher. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2523 seconds