Having problems with your Dishwashers ?

I have a SMEG SA622x dishwasher. The soap door is no longer opening. Are there any tests I can carry out to isolate the problem? Thanks


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a SMEG SA622x dishwasher. The soap door is no longer opening. Are there any tests I can carry out to isolate the problem? Thanks


... Dishwashers

My Miele G1023 Dishwasher does not start when start/stop button is pressed. After 30 sec the drain/inlet valve blinks. Carried out test and found the 240 volt does not switch to the inlet valve nor th


... Miele G892SC SS Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

Asko 1475 Dishwasher, won't fill for rinse cycles, carries on dry


Yes this is valve problem.its near to faulty.replace it.dishwasher will not fill with water during rince cycles : This is often the  ... Asko D1876 Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

I have a Maytag dishwasher model MDBTT60AWW. None of its wash modes will work when pressing their respective buttons. The Fields Service Test functioned normally with the exception of the "heated dry" and "sanitize" LEDs not being lit. Tried to perform the Manual Function Test, but none of the components would operate upon pressing the respective keys for testing their operation.


Hi, \015\012Sounds like either the control board or the keypad.Try removing power from the unit to see if it will reset.\015\012Now try running the diagnostics…RIBBON CABLE CLEANING ... Maytag 24 in. MDBH955AW Built-in Dishwasher

My maytag MDBB7100AWQ stops in mid cycle at the same place all the time (for background see robert920 problems) I tested the heater continuity and found no continuity between the heater and the outer skin of the heater and the resistance of the heater was fine. Then I run the diagnostics (Automatic function tests) and its indicated Keypad 2 which is Motor -low current. I then went on to test the resistance for the motor and found out that they were all within specs (Blue to Gray 7 ohms, Bl


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Maytag MDB7100AWB Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

Zanussi DA6141. Dishwasher will not progress from turning on at wash code c1. Test 1: No kinked hoses Test 2: Put water in by hand and it empties it. Lift out the central sieve/filter and it all appears very clean. Test 3:Inlet water filter clean. No actions except low buzz (?solenoid?) after emptying. (Possible Hint: Previously this washer sometimes stalled with knob rotated 15 degrees clockwise from C1 position and would continue to wash dishes indefinitely, if unattended. This was


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the\015\012cycle doesn't complete, check these:\015\012\ ... Zanussi Dishwashers

Working on a Whirlpool dishwasher DU915PWSS0 - The soap dispenser won't open automatically. We have replace the wax motor and have installed a new control board. When you pull up on the draw bar manually the dispenser door opens perfectly. I don't have a schematic and I don't have the test sequence so I can't run the diagnostic test. It's a blind assy process so you can't really tell if you have the draw bar over the wax motor and coupled. I need the schematic and or test sequence for the E


Please confirm if this is the model you have.\015\012\015\012I might have some access to th ... Dishwashers

Detergent dispenser door Whirlpool DU7400 won't open. I tested 300109 ACTUATOR resistance and it is closed. I ran washer and saw the actuator receives a current several times during the complete wash cycle. How else can I test? I notice the lever on the Acutator is quite floppy. Should it be stiff? Also the dispenser door does pop open if pushed from behind so that seems OK? Does anyone have the actual testing procedure for this problem? Thanks for anyone's help!


... Whirlpool 300109 ACTUATOR

I'm not able to reset my dishwasher Whirlpool ADG795, i mean, my 4-year old son was playing with buttons and, i think, the dishwasher went, but not exactly properly, into test, all the lights are flashing, i was trying to start the test properly (by pushing power button for 30 sec, hen 3 sec release and press once more) but unfortunately nothing has happened, argh... any idea?


Sounds like you are in the testing/diagnostic mode. You can exit the program by holding the buttons, or simply unplug the unit for an hour, in meantime of being unplugged, press and hold the function or power button for 5 seconds, then wait 1/2 hour ... Ariston Technologies Dishwashers

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

LG LDF8812ST dishwasher not washing: reports LE error code. Fills and drains ok. Impeller is clear, removed inside housing - no obstructions. Synchronous motor works. Tested main motor - appears to be good. Motor is not locked, looks to be in excellent condition. No shorts to ground, continuity across three main pins - not sure what the other 4 are for. My guess would be the PCB, but not sure how to test this. How do I determine if the PCB is bad?


... LG LDF9810ST Built-in Dishwasher

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers

Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.


Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher

DISHWASHER-GE GL613716A will not drain. re/re drain and removed restriction,food ect. it will not drain still. performed self diagnosis on front control panel as per trouble shooting information supplied with dishwasher when i bought it, all tests passed except when commanded on, the pump did not drain water from the dishwasher, i do not know if the pump came on as all test functions are perfomed at the same time for some reason, which made a bit of noise making it hard to even hear the pump. th


Hi,\015\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain ... Dishwashers

I have an LG ldf7811st dishwasher. My bottom arm spins with water, my middle arm does not spin but does have water coming out, and my top arm doesn't spin or have water. I have just finished taking apart the arms, the supply to the upper arms, the filters and the impeller. I cleaned everything and nothing really seemed clogged. I have tested it since and it still has the same problem. I know that they aren't spinning because i placed them in a certain position before i ran the test run. They


I'm thinking like you're thinking, that it's something affecting the water pressure, but you've done everything in the upper section, so the problem must be from below, unless you have a leak somewhere you haven't noticed and are losing pressure beca ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Maytag MDB6600AWW Unit is approx 3 years old it was finishing a load and stopped part way through sticking on heated dry. I don't know if it was there in the cycle or if the diagnostics on the board sent the message there. The light now will not shut off or move from the heated dry. I have disconnected 120 volts, removed the panel to check wiring, removed board and reassembled nothing resets the heated dry light and nothing works. I have gone through manual function test, sales floor demo test,


Have you tried pushing heated wash, heated dry, heated wash then heated dry? Sometimes this will reset it. ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Westinghouse sb925 the dishwasher creates an earth leakage in the start of the wash cycle tested drain pump wasn/t able to reach wash pump but tested o.k.is the internal light in circuit in wash cycle as it blown and haven't been able to undue the cover


... Westinghouse 24 in. MDP531 RF Free-standing Dishwasher

We have a Bosch dishwasher SHX46A06 UC/21. It continually runs. We couldn't find a diagnostic test for our model, but we did for another model. We held down the power scrub and regular wash cycles then turned it on and pressed them again. The delicate/econo light started blinking. Looking at some of the blogs, most often it seems to be the heater or the control panel - does this diagnostic test help to pinpoint what could be wrong? Also, where can we find a good manual for our model - we're havi


Here is a link to the service manual http://cgi.ebay.com/Bosch-Dishwasher-Service-Repair-Manual-/250480379703. \015\012 ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Hobart 24 in. LXIC fails sanitizer tests. The sanitizer pump is pumping out about 4-5 ml per rinse when I remove the tube at the 90 degree tube fitting. According to specs it should be about 3 ml of 8.5% solution so it seems to be providing more than enough yet the test strips show nothing.


I thought it was designed for domestic bleach at 5.25%, and looking for a solution of 50 ppm of sanitizer and rinse water. Either the elbow is blocked, or the silicone tube in the pump has collapsed. Use rubber gloves and face protection when working ... Hobart 24 in. LXIC-5 Built-in Dishwasher

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Diplomat ADP8224 The thermostat on my dishwasher (Diplomat ADP8224) has tripped and requires resetting. This has been carried out by an engineer who seems to reset somewhere under the machine. I have tried to locate the reset but with no success. Any ideas where this is and how to carry out reset


... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0277 seconds