Having problems with your Dishwashers ?

We had a repairman come in because the dishwasher wasn't working. He said to replace part numbers WD21X10169 interlock switch and part # WD21X10215 module control. I have now replaced both parts and the dishwaher is making a high pitch sound and not working.


Answers :

It could be something stuck in the pump/sump area.. sorry.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We had a repairman come in because the dishwasher wasn't working. He said to replace part numbers WD21X10169 interlock switch and part # WD21X10215 module control. I have now replaced both parts and the dishwaher is making a high pitch sound and not working.


It could be something stuck in the pump/sump area.. sorry. ... Dishwashers

Spilling water I have a Kenmore 665.15762 model dishwaher from Sears and it is spilling water throu the low part of the door. The draining is working well, is like as if the gasket is not good. I checked the gasket, but the only one I see is lateral and up and in good condition. Could be the floater too high ? Should I replace tge gasket ? Thanks for a quick reply. Viorika Aresteanu, Pierrefonds


... Kenmore Dishwashers

Hotpoint hda 3420 dishwaher. when turning, on the motor hums and doesn't kick in like usual. manual says caused by non use. "must keep the seal moist" put water in the unit, thinking it might get the seal moist. bottom filled and unit has not worked for days. assuming it's this seal: where is it? how do i get at it? what is replacement difiiculty? how much is the part? thanx ron [email protected] or [email protected]


Hi,Before thinking about replacement... pour a couple of cups of water in the dishwasher and let them soak the seal for overnight...Then if it don't go give the motor a spin...just to make sure it will go...if that don't work ... Dishwashers

Sears dishwasher 665.15882000 part #8268296 fell off and I can't find the "screw" that holds it in place...probably went down the drain. Now dishes do not "dry" on air dry. The part that matches the number for replacement parts does not look at all like the one that fell off. The one I have is round and the replacement one showing looks like some funky ninja weapon. Will this work on my machine? How easy is it to replace this part?


... Dishwashers

I purchased a replacement lower dishwasher basket for a DU8500XB-0 Whirlpool. The replacement part is W10311986. The part fits washer as far as rolling in and out, but there are 4 extra parts that I don't know how they fit, no paper work with the part from FSP. Basket probably fits more than one machine. Would like to know how the extra parts fit the basket. Thanks


Did you get a response to your question? I have the same question. ... Whirlpool W10311986 DISHRACK

When I first contacted you, I couldn't get the soap door to close in my dishwasher. As suggested I got the part. I now have the door apart. When I work the soap latch I can't see what closes the door. The part I was going to replace seems to be working correctly. over


Well IF the piece, the latch, seems to be working OK, then the only other thing it can be, is the Electronic "Drive" from the controller board, or a disconnection between the Controller and the Latch, Sometimes it can be a "Sensor" not allowing the ... Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

I have a Whirlpool Model DU943PWKQ0 dishwasher. Several of the controls on the front panel no longer work, ie normal wash, cnacel and drain, etc. Others like heavy duty wash work perfectly. It appears the most used are what is not functioning. My question is should I replace the Microcomputer assembly part number 8530929 or the Console (with overlay) part number 8274732. Can you help as I cannot really afford both!


... Dishwashers

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Viking pro dishwasher wont start/pump h20. previously cleaned out chunks of rust from feeder hose at valve under sink then it worked. light works, pumps out h2o ok. hearing clicking sounds from cycl control knob. can this part be replaced?


It sounds like you still have junk coming into the supply line. Consider running a new hot water line to thie dishwasher starting near the hot water tank. And yes, of course, each of these parts can be replaced. Joe ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

The dispenser on a Maytag Dishwasher Model WU502 is not working properly. Is there a way to clean it or does it need to be replaced? Since it is an old model can the part be replaced and if so do I need a specialist to do it?


... Maytag Dishwashers

I have a GE Profile CDW9000 series that all cycles and setting appear to work on ok BUT several of the blue lights on the control panel don't work?are burned out. As a result its hard to know what the settings are..The selection lights for 1 of the 5 clean cycles is out, the 8 hr delay light is out , as is the heated dry light and the start / reset light.My question is can these be replaced ? individually? or is it a single unit ? if so any helo with what the parts are called/ numbers and hard c


... GE 24 in. Profile PDW9800J Built-in Dishwasher

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

Our Maytag MDBH985AWSO dishwasher is 2 years old, and the start button will not work. It just started up on its own and ran an empty cycle 48 hours after our last attempt to get it running. All other buttons appear to be working. Should we replace the control board its like 200$ for the part alone.


... Maytag MDBH985AWW 24 in. Built-in Dishwasher

Judging from the information on this forum and others, we think we need to replace the control module on our Bosch dishwasher (she45m05uc/50). The general consensus seems to be that the module has an underrated relay and will burn out again. Has the board been redesigned? Is there a newer board that would work in our model? Bosch says that only part number 676962 will work. Thanks for your help, Deb


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Need to replace detergent dispenser-how difficult is this? The rinse aid portion of the dispenser does not work but it is a one piece unit. How easy is it to swap this part out. It is for the Jenn Air but is Maytag part 99003320 Thanks


Hi Jeff. These parts are easy to swap out. Just be sure to kill the power at the breaker first. Also, consider this. IF you use the newer tabe, or plastic pillow style dishwasher detergent you can just toss it into the machine and close the door, ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

I am working on a d8 dishwasher and found the cycle timer (49 sec/ 11 sec) faulty. Ordered a replacement timer from russell food equipment. The new timer is different mounting and timer motor specs. Can you tell me if this timer is the proper replacement. New part number cpn14480


... Dishwashers

Model: 1578201D PSI 4000 3.5 GPM The machine is only 2-3 years old and has always worked fantastically (with very limited usage). The inlet fitting got broken and we replaced it with a new inlet filter (part number 35169) and now it has low pressure. Is there something else we should check or replace?


Hi there,A "chattering" pressure washer pump can be caused by many things. You could have a bent or damaged inlet line, or the water supply might be too low. Fixing these is simple, but checking on the water supply is critical. Never let ... Pressure Washers

The electronic module in both dishwashers have been infiltrated by German Cockroaches and subsequently dont work. I need service replacement modules (2 Off) and I can fit them myself. Part Number 528397NAP. Where can I source these. I live in Newcastle NSW.


... Dishwashers

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Have a lg model lds 5811st model dish washer for a little over 2 years and had the le error button .called technican replaced the motor now 4 weeks later the same error button.and the cancel button wont release the water standing in the bottom.also cant get repair man to garanty his work or parts.


Take off the door cover and you will find the wires melted into a black blown in insulation. Carefully free the wires and run a quick check to see if any of the wires are broken. If they are cut them and splice them back together. It takes a while ... LG LDF6810 Built-in Dishwasher

The middle seal plate is leaking. I have received a complete new part but cannot work out how to replace same


Hi,\015\012 \015\012Please chek the links hope it helps…\015\012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

My ge dishwasher, model # gsd600d-03 works..but the spray arm is not turning..dishes come out not clean!! do they make this part still? and how hard is it to replace?? assuming that is the problem


... GE Dishwashers

My GE trash compactor just quit working. A little over 1 year old. I opened it and found inside the motor frame a magnetic contact that is burned up. Nothing else is wrong. This part shouldn't cost more than $10 . I can't find it anywhere. Do I have to buy a new motor for $180 to replace a perfect motor with a burned up $10 contact?


Parts sadly, aren't as inexpensive as they used to be. Hopefully, you can get away with the $25 part.\015\012\015\012http://www.repair ... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1093 seconds